Laserfiche WebLink
Name of Supplier,Owner or Dealer Address No.and Streets) City State Date of Test <br /> 15. TANK TO TEST <br /> 15a. BRIEF DIAGRAM OF TANK FIELD 16. CAPACITY From <br /> �+`�• /�� Station Chart <br /> H `r W >.,,) 1 Nominal Capacity O 00 1:1 <br /> Tank Manufacturer's Chert <br /> Identity by positionh� (''� Gallons Company Engineering Data <br /> 2� u mom L.i By most accurate Charts supplied with <br /> Brand and Grade capacity chart available v D�'v ❑ Other <br /> Gallons <br /> Total Gallons <br /> 17. FILL-UP FOR TEST Gallons ea.Reading <br /> Stick Water Bottomin in. Inventory Doo <br /> before Fill-up <br /> to'h" Gallons Tank Diameter <br /> 18. SPECIAL CONDITIONS AND PROCEDURES TO TEST THIS TANK ❑Water in tank ❑ Line(s)being tested with LVLLT <br /> See manual sections applicable.Check below and record procedure in log(27). ❑High water table in tank excavation <br /> Transfer total to line 25e <br /> use maximum allowable test pressure for all tests. 19. TANK MEASUREMENTS FOR <br /> Four pound rule does not apply to doublewaued tanks. TSTT ASSEMBLY <br /> 21. VAPOR RECOVERY SYSTEM ❑stage I Ej stage II <br /> Complete section below: Bottom of tank to grade' in. <br /> ............................ <br /> Add 30"for'T'probe easy........................... 30 in. 24b. COEFFICIENT OF EXPANSION <br /> 1. Is four pound rule required? yes ❑ No ❑ Total tubing to assemble—approximate............. in. RECIPROCAL METHOD <br /> Type of Product ............... .�..•1+V-�.��_ <br /> 20. EXTENSION HOSE SETTING <br /> 2.Height to 12"mark from bottom o/tank in. Hydrometer Employed .................................. H <br /> Tank top to grade'.................................. in. <br /> Extend hose on suction tube 6"or more Temperature in Tank <br /> below tank top...................................... <br /> 3. Pressure at bottom of tank P.S.I. in After Circulation........................................ °F <br /> � �V <br /> Temperature of Sample................................. °F <br /> 4. Pressure at top of tank <br /> P S 1 'If Fill pipe extends above grade,use top of fill. ^ <br /> - �J <br /> 22. Thermal-Sensor reading atter circulation Difference(+/-)......................................... /— °F <br /> .y�+w°g�a W <br /> in. I °F Observed A.P.I.Gravity ................................. <br /> Depth o1 burial -- Between <br /> 23. Digits per°F in range of expected change Ail Reciprocal !"t� Page N <br /> digits <br /> Tank dia. in <br /> COEFFICIENT OF EXPANSION (Complete after circulation) 19010 ' <br /> 24a. Corrected A.P.I.Gravity Total quantity in Reciprocal Volume change in <br /> full tank(16 or 17) this tank per°F <br /> Water table in Transfer to Line 26a. <br /> Observed A.P.I.Gravity................................... <br /> NOTES: <br /> Fydrometer employed................................... H <br /> Observed Sample Temperature °F <br /> 24c. FOR TESTING WITH WATER see Table C d D <br /> Corrected A.P.I.Gravity Water Temperature after Circulation <br /> @ 60°F,From Table A.................................... Table C................................................ 'F <br /> Coefficient of Expansion Coefficient of Water <br /> for Involved Product Table D ............................. <br /> The above calculations are to be used for dry soil conditions to .................... <br /> From Table B................ . . ...... ........... .... <br /> establish a positive pressure advantage,or when using the four pound <br /> . . . . . <br /> rule to compensate for the presence of subsurface water in the tank Transfer COE to Line 25b. Added Surfactant? ❑yea E No Transfer COE to Line 25b. <br /> area_ // <br /> Refer to N.F.P.A. 30, Sections 2-3.2.4 and 2-7.2 and the tank 25. (a) x (b) = lc) gallons <br /> manufacturer regarding allowable system test pressures. Total quantity in Coefficient of expansion for Volume change.in this tank <br /> full tank(16 or 17) involved product per*F <br /> 26. a LAt 0% �I�—L N Q = t V� ?_moi' 1 This is <br /> Vol,,­rthnngn p-"F f25 or 24h1 Digifs per"F in Leet Volume change per dlgit test <br /> ^/ a <br />