INSTALL TANK TOP UPGRADE 1994 - Laserfiche WebLink

Home Browse Search

FVEEDER-ROOT DISPENSER PAN SENSOL INSTALLATION INSTRUCTIONS IMPORTANT! THIS MANUAL REQUIRES ALL PRELIMINARY SITE PREPARATION IS COMPLETED, AND THAT FIELD WIRING FROM THE MONITOR TO THE SENSOR JUNCTION BOX IS IN INCE. IT CONTAINS INSTALLATION AND WIRING PROCEDURES FOR THE INSTALLATION OR REPLACEMENT OF A DISPENSER PAN SENSOR ONLY! FOR NEW INSTALLATIONS, REFER TO THE TLS-350 'SITE PREPARATION AND INSTALLATION INSTRUCTIONS,' MANUAL NO. 576013-622, PROVIDED WITH THE SYSTEM. SECTION 1. INTRODUCTION hardware: A. GENERAL 1 - Cable, including connector,Part No. 576006-750 1. This manual contains installation procedures for the 1 - Wiring Kit, Part No. 312020-969 installation or replacement of a Veeder-Root Dispenser Pan 1 -Installation Instructions, Manual No. 576013-841 Sensor, Part No. 794380-320, in a TLS-350 UST Monitoring Mounting brackets must be ordered from the dispenser pan System designed and manufactured by Veeder-Root Company. manufacturer. This manual assumes all preliminary site preparation is com- pleted, and that field wiring from the monitor to the sensor A. GENERAL Before you install the dispenser pan sensor, junction box is in place. consider the following important requirements: If site preparation is necessary, refer to the TLS-350 'Site 1. The sensor should rest in the cup or lowest point of the Preparation and Installation Instructions; Manual No. 576013- dispenser pan. 622;or contact your Veeder-Root representative for assistance. l. 2. It is recommended that the sensor be moui{ted in a.true 2. When a vertical bar I appears adjacent to text or illustra- vertical position to ensure proper operation of the sensor. tions,information has been added or changed at the last revision 3. Ensure that there will be enough room to pull the sensor date. straight out of the pan. B. DAMAGE CLAIMS B. INSTALLATION. The wires between the monitor and each 1. Thoroughly examine all components and units as soon as dispenser pan sensor location must be of a type designed for use received. If damaged,write a complete and detailed description in the presence of gasoline and oil,and must be between AWG of the damage on the face of the freight bill. Have the carrier's 14 and AWG 18. The conduit must be properly sealed in agent sign the description. accordance with the National Electrical Code (NFPA 70) and NOTE: Insist that the carrier's agent verify the the Automotive and Marine Service Station Code (NFPA 30A) �,,1 since they pass from a Class I,Division I or Division II area into inspection and sign the description. a nonhazardous area. 2. Immediately notify the delivering carrier of damage or loss. alii WARNING:TO AVOID ELECTRICAL SHOCK-�WHICHCOULD KILL YOU, BE SURE AC POWER TO THE This notification may be given either in person or by telephone. MONITOR IS OFF DURING INSTALLATION. Written confirmation must be mailed within 48 hours. Railroads and motor carriers are understandably reluctant to make 1. Turn OFF AC power to the TLS-350 system. adjustments for damaged merchandise unless inspected and reported promptly. CAUTION: DO NOT INSTALL THE DISPENSER 10 PAN SENSOR IF THERE IS ANY LIQUID IN THE 3. Risk of loss, or damage to merchandise remains with the DISPENSER PAN. FAILURE TO COMPLY CAN buyer. It is the buyer's responsibility to file a claim with the RESULT IN EQUIPMENT DAMAGE OR carrier involved. UNDETECTED POTENTIAL ENVIRONMENTAL 4. Immediately advise your Veeder-Root representative, AND HEALTH HAZARDS. distributor, or the factory so that we may assist you_ 2. Make sure no liquid exists in the dispenser pan. C. RETURN SHIPPING. All shipments of Vecder-Root NOTE: If this is an existing installation where mounting products must be prepaid. If the sensor is damaged,return it in hardware is already in place and only the dispenser pan the original shipping container with shock absorbing material sensor is being replaced, simply remove the old sensor provided. Veeder-Root will accept no liability for damage and proceed to Section B.5. caused by improper packing. Address the shipment to Veeder- Root Co.,6th Avenue at Burns Crossing,Altoona,Pennsylvania IMPORTANT: BEFORE REMOVING AN EXISTING 16603. DISPENSER PAN SENSOR BE SURE TO MARK FIELD WIRES IN THE JUNCTION BOX TO MAINTAIN SECTION 2. DISPENSER PAN SENSOR CORRECT SENSOR WIRING POLARITY DURING THE INSTALLATION REPLACEMENT PROCEDURE. The dispenser pan sensor conics with the following installation 3. Choose a location in the dispenser pan where the sensor can bo pul;cd straight out for future service or replacement,and 2