Laserfiche WebLink
UL/ULC LISTED SECONDARY CONTAINMENT FITTINGS <br />•a�r•T.:� :�� rM:�t,: <br />TERMINATION CONCENTRIC REDUCERO) <br />WITH 3/4" NPT <br />3/4" NPT <br />+ TAP <br />Sizes available for Termination Concentric Reducers, <br />with and without tap: 3"x 2", 4"x 3", *6"x 4". <br />SIZES <br />45° ELBOW SLEEVE COUPLING <br />-i C <br />A <br />SADDLES _ <br />SIZES AVAILABLE <br />Belled Side Outlet <br />Threaded Side Outlet <br />NPT Internal Threads(2) <br />3„x2„ <br />3"x1„ <br />4" x 2" <br />3" x 11/'„ <br />4" x 3" <br />3" x 11/2" <br />7 <br />4"x1' <br />3 <br />4" x 11/1' <br />21/2 <br />4„ x 1'A" <br />- –J <br />SizeA <br />Ye" <br />B <br />±1/811 <br />C <br />± 1/e" <br />D <br />± Ye" <br />E <br />± 1/61, <br />F <br />± 1/e11 <br />3" <br />6 <br />7 <br />14 <br />3 <br />21/2 <br />21/2 <br />4" <br />71/2 <br />8 <br />14 <br />3 <br />3 <br />21/2 <br />6"* <br />8 <br />9 <br />16 <br />4 <br />4 <br />3 <br />*NOTE: 6" secondary containment fittings are not UL/ULC Listed. <br />PRESSURE RATINGS <br />TERMINATION <br />CONCENTRIC REDUCER <br />F <br />� <br />7� <br />1 <br />_L E <br />Bending Properties of RED THREAD II Pipe <br />Nominal <br />psig at <br />Size <br />1500 F <br />3" <br />90 <br />4" <br />80 <br />6"* <br />(4) <br />TERMINATION <br />CONCENTRIC REDUCER <br />F <br />� <br />7� <br />1 <br />_L E <br />Bending Properties of RED THREAD II Pipe <br />Nominal <br />�F/24* <br />Pipe Size <br />Test Method <br />50 ft. <br />2„ <br />15.2 m <br />ASTM D-2105 <br />80 ft. <br />3„ <br />24.4 m <br />4„ <br />100 ft. <br />22,700 psi <br />30.5 m <br />TYPICAL PHYSICAL PROPERTIES(')(') <br />Property <br />Value <br />Value <br />Test Method <br />Tensile Strength — Axial at 75o F <br />11,900 psi <br />82.05 MPa <br />ASTM D-2105 <br />at 150 F <br />9,300 psi <br />64.12 MPa <br />Compressive Strength — Axial at 75' F <br />22,700 psi <br />156.51 MPa <br />ASTM D-695 <br />Modulus of Elasticity In Tension at 75° F <br />1.92 x 106 psi <br />1.32 x 104 MPa <br />ASTM D-2105 <br />at 150° F <br />1.70 x 106 psi <br />1.17 x 104 MPa <br />Ultimate Hoop Tensile Strength at Burst <br />Average at 75° F <br />44,000 psi <br />303.37 MPa <br />ASTM D-1599 <br />Long Term Hoop Strength at 75° F <br />Cyclic Pressure (150 x 106 cycles) <br />9,140 psi <br />63.02 MPa <br />ASTM D-2992 <br />at 150° F <br />8,020 psi <br />55.30 MPa <br />Procedure A <br />Thermal Expansion Axial <br />2" 3" 4" pipe <br />1.09 x 10-5 in./in./1F <br />1.96 x 10-5 mm/mm/°C <br />AOSI-TM16-3 <br />Thermal Conductivity <br />2" 3" 4" pipe <br />2.9 BTU /(ft.2)(hr.)(dF/in.) <br />0.42 W/(m)(°K) <br />AOSI-TM16-15 <br />Specific Gravity <br />1.85 <br />1.85 <br />ASTM D-792 <br />Flow Factor <br />Hazen -Williams Coefficient <br />150 <br />150 <br />AOSI <br />(1) A 3" x 2" reducer bushing which is (2) Threaded connections (3) Sharper bends should be eliminated (4) Data not available at time of (6) Pipe is manufactured in compliance <br />not UL/ULC Listed is available for must be made with a to avoid stress concentration which printing. with ASTM D-2996. Refer to general <br />use with the 4"x 3" termination flexible connector. would result in premature pipefailure specification sheet in catalog for the <br />concentric reducer. under pressure conditions. (5) Tests run on pipe samples. D-2996 designation code. <br />