WP0039455 - Laserfiche WebLink

Home Browse Search

i I I MOUNTING BRACKET UNISTRUT FOR MOUNTING R£CTiEER(TYP) AIR-C OLED, REC77RER UNIT (SEE NOTE I &3.) I"GHS CONDUIT W/(I)- AWG ANODE AC DISCONNECT SW N HEADFR CABLE(BLACK), (1)-J4 AWG j STRUCTURE CABLE(WHITE) TO AC POWER SUPPLY i Q ANODE JUNCTION BOX 3' 1/2'IRS CONDUIT W/AC (SEE NOTE 1� APPROX. RECTIFIER CABINET POWER TO FX BREAKER PANEL SEE DETAIL 4 a-119 PUMP STA77ON NAME #4 REBAR 70 INCHES APART, EX PUMP STATION EACH WAY& CENTERED IN SLAB 2-GRS CONDUIT W/(2 OR 4 OR 6) — 2. #8 AWG/HALAR NMWPE ANODE CABLES 6 INCH THICK (BLACK) CONCRETE PAD o i� CRYOPL /tOCKTON- PS (rrP} 1'GRS CONDUIT w/(r-#4 AWG srRucruRE � Rrcri�IER u zD IN 00 � a CABLE(WHITE), AND P)-J'8 AWG TEST j,�� CABLE(WHITE) 30' BOLLARD MIN. SEE DLTAIL( i f CP—`20 "E74 1 4 FT-8 IN (TYP) r TO ANODES TO PIPELINE NOTES., 1. BOLLARDS ARE SHOWN IN THE CP SrAT10N SITE PLANS,ARE INDICATED AS NEEDED AT EACH SITE. 2. BOLLARDS SHALL BE INSTALLED WILH SUFFICIENT SPACE FROM THE CABINETS TO ALLOW FULL NOTES. OPERATION DF THE CABINET DOORS. f. THE ENGRAVED MTCARPLATES SHALL BE-X6 INCH THICK AND 3. CONCRETE MIX SHALL BE TYPE If CONCRETE' WITH A WATER-TO-CEMENT RATIG BY WEIGHT NOT TO NOTES., LETTERING SHALL 8ETA TA%INCH HIGH, L L BE ON HACK. i E7 CLED .55 AND SHALL HAVE A MINIMUM 28-DAY COMPRESSIVE STRENGTH OF 3,000 PSI, 1. INSTALL RECTIFIER AND JUNCT7ON BOX ON THE INTERIOR WALL OF THE PUMP STATION BUILDING. 2 THE PLATES SHALL BE BOLTED TO THE RECTIFIER CABINET WITH i 4. CONCRETE REINFORCING STEEL SHALL CONFORM TO ASTM A615, GRADE 0, DEFORMED. 2- FOR CABLE TRENCH, SEE DETAIL 2/CP-20, 1/4 INCH DIAMETER BRASS BOLTS. 5- CONCRETE PAD FINISH SHALL NAVE FINE HAIR LIGHT BROOM FINISH. J. INSTALL AN AC DISCONNECT SWITCH W/LATCH LOCK ON THE UNISTRUT ABOVE THE JUNCTION BOX. rf1 NEW CONCRETE PAD rf1 WALL-MOUNTED INTERIOR RECTIFIER RECTIFIER I.D. PLATE CP-19 NOT TO SCALE CP-19 NOT TO SCALL CP--19 NOT TO SCALE I NICKEL PLATED ENGRAVED MICARTA BRASS HARDWARE .+ 1 x s 4 5 5 e F-----+--a !ABEL (TYP) COPPER SHORTING ® ®o ° J4 AWG/THHN ANODE STRAP(5x1 xi/4"THICK) @ @ ® ® ®' a HEADER CABLE 0 0 0 0 0 0 TO NEW RECTIFIER POSITIVE 0.001 OHM 25 AMP 0 ® ® po ® aCABLE PERMANENT NYLON SHUNT(SEE NOTE 1.) o MARKING TAG a o 0 0 18 AWG THHN TEST CABLE MATAG COPPER LUG(TYP) •ror o RESISTANCE WIRE (SEE NOTE 2.) o ❑ ❑ ❑ o FIBERGLASS JUNCTION BOX AN- I 18 AWG HALAR HMWPE CABLES FROM ANODES FABRIC REINFORCED (SEE NOTE 1.) PHENOLIC PANEL i (114"THICK) ABBREVIATIONS NUMBER i COVER AN - ANODE ANODE NUMBER E CABLE IDENTIFICATION(TYP) OR - DRAIN CABLE SEE DETAIL Q5 1"GRS CONDUIT DPL - DISCHARGE PIPELINE (cr-rgTT - TEST 2"GRS CONDUIT NOTES., p^^j 1. SEE TABLE 1 ON SHEET CP-1 FOR NUMBER OF ANODES REQUIRED FOR EACH SITE 1 2- RESISTANCE WIRE TO BE INSTALLED BY THE ENGINEER. J. IDENTIFY CABLES PER DETAIL 5/CP-19• �1 ANODE JUNCTION BOX n CABLE IDENTIFICATION DEPARTMENT❑F TC)N oP"`❑�"IT'E° C[TY°F ST°CKTON, IPAL ANIA CP-19 NOT TO SCALE CP-19 NOT TO SCALE t� a' Wca,wL•HN°rD ENGINEERING NO. REVISIONS 8Y APP DATE DESIGNED UNDER THE DIRED71°N°e SI-rEET CATHODIC PROTECTION REPAIRS SWPS&FORCEMAINS DIL]N7C1P•1LUTiLITILS � jdhcorrosion �-20-2018 tii4�. DEPAR"IlILi,7T consultants, I n c. C/A 11 N O��I C F R O'[1�16 II Q BUJ W1 D)�Il(,�I�S it ll� A coa eM�io cAI i Das aeoisrRe7r❑N FxalaEs e-ao-r e onTe w pa tq 7Cs6 �� k.',a A 95ZIJ 00 cord, Pass Court, *Ew S,ockmn,C.1 75206 DESIGN;T°N DATE 5-3-7 7 rl�o,��:(2o;937.e7On Concord, CA 94520 DRAwN.rDR-....-� DATE sa-.�- cAt'E 7e1. {925}927-6630 SYpCI.fUIU,CA98FO1SNI4 fviUNIC12RLU7PEITESAEPAC[7MtEN7 cH-cl(=_D, na DATE 5-3-17 19 OF 20sHEL s