Laserfiche WebLink
l <br /> MSZ BLS-1 .1 2 0l <br /> Page 2 <br /> Step 7: Install The Eccentric Insert&Multi-Sync Reducer <br /> • Dry fit the Eccentric Insert.Make sure It fits properly over the pipe&inside the <br /> sleeve. <br /> • Dry fit the Multi-Sync Reducer <br /> • Adjust the positions so that they lineup properly with the Repair Sleeve&Pipe. <br /> Note: A proper fit will not cause extra pressure or force to the sleeve and will <br /> allow a longer lasting repair. !ti <br /> • Once you have the part lined up correctly z'` <br /> 1. Pull back the Multi-Sync Reducer&Eccentric Insert <br /> 2.Apply Zip Tite bonder all around the Eccentric Insert, <br /> 3. Slide Eccentric into the Repair sleeve In the proper position <br /> 4.Apply Zip Tite bonder all around the Multi-Sync Reducer e�l� <br /> 5.Slide the Multi-Sync Reducer Into It's proper place <br /> 6. Set the Clamp the around the sleeve&over the Eccentric Insert and tighten <br /> "snugly". <br /> 7.Set clamp over reducer end on the pipe&tighten enough to create a seal <br /> around the pipe. <br /> Pipe SI a air Kit Cuff Insert Eccentric Insert I n CI m <br /> /4"Rigid Conduit MSZ BLS-1.1 UIZ BLS 3.1x1.1 UIZ 3.Sx2.6E URZ MS 2.6x1.1 16 <br /> Rigid Conduit MSZ BLS-1.4 S 3.1x1.4 UI .5x2.6E Z MS 2.6-&L4-- 2C <br /> 1"Flex Pipe MSZ BLS-1.6 UIZ BLS 3.1x1.6 UIZ 3.5x1.6 N/A 24 <br /> � yL <br /> Step 9: FIII With DBF II,Insert Fill Plug TOOLS REQUIRED: <br /> Assemble DAG&DBF II(see instructions on DPM website). Gloves and Static Mixer <br /> • Purge 1-2 oz. 5/16"Nut driver (for Band Clamps) <br /> i FIII fitting slowly. DAG Caulk Gun (for DBF II) <br /> Note: Use Remote Fill option if access is limited DAGP Caulk Gun (Pneumaticversion for DBF II) <br /> i Insert fill plug when filling is completed. DAG III Caulk Gun (for DBB V) <br /> • Clean any spilled DBF II with DBC and dispose <br /> of remaining products per local requirements. PRODUCTSNEEDED• <br /> I <br /> DBC Cleaner Each DBF II&DBB V come <br /> Note: After 1 hour DBB III Bonder with a Static Mixer <br /> the repair job maybe DBF 11 Polysulfide Liquid Fill <br /> hydro-static tested DBB V Bonder(for Poly or Fiberglass sumps) <br /> FILL Volume: (per repair boot) <br /> Volume of DBF II needed = 9.5 oz <br /> _._ Volume of DBB III needed = <br /> Remote Fill Option: Volume of DBB V needed = <br /> The following parts are available to order if you can not <br /> properly position the assembled DBF II applicator gun to Parts in kit: <br /> "fill"the repair. The Remote Fill parts provide a flexible Cuff Insert UIZ BLS 3.7.xsee7able <br /> 3.5 <br /> extension for the filling process. Sleeve UIZ x <br /> Eccentric Insert UIZ 3.5.5x5eeee Table <br /> RF Adapter 24"tube with male&female ends Multi-Sync Reducer URZ MS 2.6xSeeTable <br /> RFA Tube-24 '/"Tubing in 24" lengths 5 clamps 2#44,1#40,2#See Table <br /> RFA Tube A"Tubing in 200' length roll Fill Port Plug RFA xPlug <br /> RFATubexTube %2"Tube Coupling Install Instructions <br /> RFA xFemale %:"Tube-Female Fill Portend <br /> RFA xMale %"Tube-Male Fill Portend <br /> RFA xPlug W Tube-Male Plug for fill port <br />