Laserfiche WebLink
Multi-Sync lnstail,afie InstrLKliom <br /> ®PM Mk?MjThi <br /> For' Blueline Medium R tirx}ss kit provides the Multi-9yncFbpair for applications where the Pipe isoc)mingthruthr <br /> t slmp wall straight or at an angle. <br /> WAF N'Na Prepare all surfaoesto be bonded prior to completing installation steps below. <br /> MSS B�LM-xx <br /> Failure to follow each step will void warranty&may result in premature failure of penetration fitting. <br /> -� l� <br /> Page 1 This Kt aroiesfor repairinq 13ueline Medium Fittings <br /> C� l 5_ 0 _le. r c,, is"i " 1 <br /> General Instnictionsfor CIJmwa lbray all surfacesto be bonded with MCGearter and allow to air dry or wipe excesswith a dean dry <br /> doth. Ebrfaces must be dry before applying bonder. <br /> General Instructions for: BONDING TOPOLYSUMPSORI IBUGLASSSUMPS: Clean,sand and rough up sump surfaces. Clean fitting and <br /> apply aIRTFiEor DLII between Bonding Rng&sump wall. <br /> Srazl1: Fbmove Old Boot STEP 2: Clean all Fair Components SrEP3: Place&Dry Ft Q,ff F7Ing,Seeve&Insert <br /> • Remove damps Clean all repair componentswith DBC Wrack the split cuff ring over the old fitting <br /> Out away old boot prior to installation Mack the split insert over the pipe <br /> • Clean&sand fitting Vvlr d the split sleeve over the pipe&up to the <br /> flit Qealih bonding ring with the fill port up <br /> Cliff cave <br /> Rng <br /> h_ <br /> FmetltriCtnt Multi 91rnc <br /> Insert Inducer <br /> llt t <{ SrEP5: Install TheSeme,Cltff Fang&Inset STEP 6:Install&Bond EmerrtricInsert&Mufti 9/nc <br /> • Appty Zp-Tule to the outer surface of the p� �t�t� <br /> insert and fully seat inside of cuff Wrack Exentric Insert around the pipe <br /> • Apply Zp-Tate to the inner surfaoe of the cuff Wrack Mufti�yncFeducer around the pipe <br /> ' ; w ring and slide all th;way onto the cuff Apply Zp-Tite to split area on Eboentric Insert,press <br /> ` <br /> Pbsition the sleeve with t he fill port at the top ends together&clamp <br /> • Once you have the sleeve lined up correctly, Apply Zp-Tite to split areaon Multi-' m=Fbduoer, <br /> 1.Apply a bead of Zp-Tit e all around t he press ends together&damp <br /> SIPP4: Bond Seeve,CuffRing&Insertng <br /> outer surface of the cuff ri <br /> • Apply Op Tate to split cuff ring. Use 1 of 2.Side sleeve over Gaff ring&snap in place <br /> the damps to hold in place while curing. (fill port at top) <br /> • Apply Zip-Tite to the split insert and use 1 3.Set the Clamp the around the sleeve& <br /> of the dampsto hold in place while over the cuff ring and tighten rfaJ-6id- <br /> curirxj <br /> • Apply Zp Tite to t he split sleeve and use 2 <br /> damps to hold in place while curing. <br /> • Leave these damps in place for approx 30 <br /> minutesfor curing before prooeed ingto <br /> the next step <br /> r <br />