WORK PLANS - Laserfiche WebLink

Home Browse Search

CONCRETE REPAIR NOTES TILE NOTES 1. PREPARED SURFACE SHALL BE SMOOTH AND FREE CLEAN SUBSTRATE SURFACES FREE OF GREASE, DIRT, INTERIOR FLOOR APPLICATION: OF RIDGES AND IRREGULARITIES INCLUDING THOSE DUST, ORGANIC IMPURITIES AND OTHER MATERIALS THINSET OVER CONCRETE SUBSTRATE AND CONCRETE OCCURRING IN CONCRETE AND FROM MASTICS. WHICH WOULD IMPAIR BOND. SUBSTRATES WITH WATERPROOF OR CRACK ISOLATION 2. INITIAL CONCRETE SLAB PREPARATION: MEMBRANE. lop • REMOVE DIRT, OIL, SOAP, GREASE, MASTIC AND BACKING BOARD: TCNA SYSTEM: F113 OR F122 AT WATERPROOF C 2111 PTAPBUCKS COFFEE COMPANY OTHER BOND-BREAKING CONTAMINANTS. "DUROCK BRAND CEMENT BOARD" BY USG (OR EQUAL) MEMBRANES STARBUCKS COFFEE • SURFACE SHALL BE SMOOTH AND FREE OF 1. USE CEMENTITIOUS BACKING BOARD, EXCEPT INSTALLATION STANDARD: ANSI A108.5 COMPANY UNWANTED RIDGES FROM WITH MASTICS OR WHERE GYPSUM BACKING BOARD IS INDICATED. SETTING MATERIALS:THINSET MORTAR; 3/32 INCH 2401 UTAH AVENUE SOUTH CONCRETE. 2. SCREW ATTACH UNITS WITH 1 INCH LONG MINIMUM THICKNESS SEATTLE,WASHINGTON 98134 3. SURFACE REPAIR: DRYWALL SCREWS SPACED 6 INCHES ON USE CEMENTITIOUS SANDED GROUT UNLESS (206)318-1575 • FILL HOLES, SPALLS, CRACKS, VOIDS AND JOINTS CENTER ALONG FRAMING. INSTALL FIBERGLASS INDICATED OTHERWISE. THESE CONFIDDRAWIENTIAL AND SHALL REMAND IN CONFIDENTIAL AND SHALL REMAIN THE SOLE PROPERAS RECOMMENDED BY THE SYSTEM REINFORCING TAPE AT JOINTS BETWEEN • USE EPDXY GROUT AT SERVICE AREAS BEHIND WHICH IS HE OW NRR OF THCORPORATION, °COPYRIGHTIN OT MANUFACTURER WITH MINIMAL RESIDUE ON PANELS. COMPLETELY EMBED IN A THIN SET COUNTER. REPRODUCED WHOLE OR INN`P RT)BSHARED WITH THIRD PATIESIN ANY SURROUNDING SURFACE AND AS REQUIRED TO MORTAR BED. TROWEL MORTAR SMOOTH WITH ON OTHER PROJECTS ORUXTENSO SnANNER TO THIS PROVIDE A SMOOTH, LEVEL AND EVEN ADJACENT SURFACES. INTERIOR FLOOR APPLICATION: CONSENTO STAR UCKSCORPORATION. N SUBSTRATE. THICKSET OVER CONCRETE SUBSTRATE INTENDDRAWINGS ESSSSDESIGIN1INATENTFORA 4. FINAL PREPARATION: SLAB LEVELING: TCNA SYSTEM: F112 Ps°e°CTTO CHANGE AT AN STORE ND DO • SURFACES TO BE TREATED SHALL BE CLEAN, DRY 1. PRIOR TO INSTALLATION OF THINSET FLOOR TILE, INSTALLATION STANDARD: ANSI A108.1 NEITHER PAR°�ACTUAL A�EA°OOB�GATION R LIABILITY TO THE OTHER(EXCEPT STATED AND ABSORBENT. SUBSTRATE SHALL BE BROUGHT TO PLANE BOND COAT: THINSET MORTAR OVER THICKSET ABOVE)UNONTILAWRITTEN AGREEMENT IS s FULLY EXECUTED BY BOTH PARTIES 5. APPLICATION OF REPAIR AND RESURFACING SURFACE WITH VARIATIONS NOT TO EXCEED 1/8 MORTAR BED; 3/32 INCH MINIMUM THICKNESS MATERIALS: INCH IN 4 FEET (CUMULATIVE) AND 1/4 INCH IN SLOPE MORTAR BED EVENLY TO FLOOR DRAINS. STARBUCKSTEMPLATE VERSION i2017.05.18 • INSTALL TROWELABLE UNDERLAYMENT AT 10 FEET (NON CUMULATIVE). SMOOTH ABRUPT USE CEMENTITIOUS SANDED GROUT UNLESS N LOCATIONS WHERE SLOPES ARE INDICATED AND CHANGES IN PLANE. SPECIFIED OTHERWISE. mm AT OTHER LOCATIONS AS APPROPRIATE TO 2. USE THINSET MORTAR OR OTHER CEMENTITIOUS USE EPDXY GROUT AT SERVICE AREAS BEHIND INSTALLATION CONDITIONS. FILLER FOR SLAB LEVELING. COUNTER. 5858 Wilshire Blvd#200 T:323.954.8996 • INSTALL SELF-LEVELING UNDERLAYMENT AT Los Angeles,CA 90036 F:323.954.8965 N OTHER LOCATIONS AS NECESSARY TO CORRECT CRACK ISOLATION: WALL APPLICATION: www.Valerioinc.Dom*infoCvalerioinc.com U ARCHITECT SLAB SLAB FLATNESS AND LEVELNESS. "DAL-SEAL CIS" BY DAL-TILE CORP. (OR EQUAL) GYPSUM BOARD SUBSTRATE OFRECORD ti�ARC 6. APPLICATION OF SEALER: TCNA SYSTEM: SIMILAR TO W243 "°"^Lf� N DO NOT APPLY SEALER TO SLABS OR PORTIONS WATER PROOF MEMBRANE: INSTALLATION STANDARD: ANSI A 108.5 z LIC228 O. C 20 OF SLABS INDICATED TO RECEIVE POLISHING "DAL-SEAL TS" BY DA-TILE CORP. (OR EQUAL) SETTING MATERIALS:THINSET MORTAR ?� E 3,R,S¢�ti SYSTEM OR A FINISHED FLOORING MATERIAL. 1. INSTALL WATERPROOF MEMBRANES IN USE CONTENTIOUS SANDED GROUT UNLESS BEHIND ^"F° • DO NOT APPLY SEALER TO SLABS OR PORTIONS ACCORDANCE WITH MANUFACTURER'S BAR OR RESTROOM. o OF SLABS INDICATED TO RECEIVE POLISHING INSTALLATION INSTRUCTIONS AND IN ACCORDANCE SYSTEM OR A FINISHED FLOORING MATERIAL. WITH ANSI A108.13. WALL APPLICATION: U • REMOVE ALL DIRT, DEBRIS, OR CURING 2. INSTALL WATERPROOF MEMBRANES AT ALL TILE BACKING BOARD o COMPOUNDS USING SURFACE PREPARATION LOCATIONS WITH OCCUPIED SPACE BELOW OR TCNA SYSTEM: SIMILAR TO W244 CLEANERS AS RECOMMENDED BY MANUFACTURER WHEN REQUIRED BY LANDLORD IN A LEASED INSTALLATION STANDARD: ANSI A108.5 N FOR CONDITIONS. PROPERTY. SETTING MATERIALS:THINSET MORTAR s APPLY SINGLE COAT OF SEALER USING A LOW 3. AT SLAB ON GRADE LOCATIONS, INSTALL USE CEMENTITIOUS SANDED GROUT UNLESS BEHIND ELI PRESSURE SPRAYER. APPLY IN SINGLE WATERPROOF MEMBRANES ONLY ALONG THE BAR OR RESTROOM. a> SATURATING APPLICATION. EVEN OUT PUDDLES PERIMETER OF TILE AREAS. EXTEND THE LI WITH MICROFIBER APPLICATOR BEFORE MATERIAL MEMBRANE UP THE WALL AND A MINIMUM OF GROUTING: LID J LO 2 HAS A CHANCE TO FULLY DRY. ALLOW TREATED 12 INCHES OUT ONTO THE FLOOR SURFACE. CEMENTITIOUS SANDED GROUT: "ULTRA/COLOR" BY L � rn �I SURFACES TO DRY AND REMOVE ANY DRIED 4. AT ABOVE GRADE LOCATIONS, INSTALL MAPEI (OR EQUAL) � °� o m U POWDER RESIDUE. WATERPROOF MEMBRANE COMPLETELY OVER CEMENTITIOUS UNSANDED GROUT: "KERACOLOR S" BY Z 2 I x APPLY SINGLE COAT OF SEALER USING A LOW FLOOR SURFACES INDICATED AND UP THE WALL. MAPEI (OR EQUAL) < 3: N PRESSURE SPRAYER. APPLY IN SINGLE EPDXY GROUT: "KERAPDXY" BY MAPEI (OR EQUAL) w Q w SATURATING APPLICATION. EVEN OUT PUDDLES 1. COMPLY WITH PROVISIONS OF ANSI A108.10 mN WITH MICROFIBER APPLICATOR BEFORE MATERIAL 2. APPLY GROUT RELEASE TO TILES PRIOR TO N HAS A CHANCE TO FULLY DRY. ALLOW TREATED GROUTING. "ULTRA CARE GROUT RELEASE" BY STORE#: 8979 N SURFACES TO DRY AND REMOVE ANY DRIED MAPEI (OR EQUAL). CASEWPROJECT#: 20927-065 d POWDER RESIDUE. ISSUE DARE CONCEPT: 01/30/20 m DESIGN MANAGER: Tina Marinic o LEED@ AP: N/A N N PROGRAM MANAGER: Tina Marinic v CHECKED BY: m O or Revision Schedule Q Rev Date By Description U t6 SHEET TITLE: a GENERAL NOTES N W SCALE:AS SHOWN N o SHEET NUMBER: N M 16