Laserfiche WebLink
27 . Sensor Calibration / S 30 , HYDROSTATIC 31 . <br /> PRESSURE VOLUME MEASUREMENTS IV) 3Q . TEMPERATURE COMPENSATION ' 3A . NET VOLUME 391, <br /> CONTROL RECORD TO .001 GAL . USE FACTOR lal CHANGING ACCUMULATED <br /> LOG OF TEST PROCEDURES EACH READING CHANGE <br /> ZB . 29 . Slandpipe Level Product in 33 . 35 . 36 . 37 . <br /> Record details of selling up 32 . Product . Temperature <br /> UAIE and running test . ) Use lull Reading in Inches Graduate Replaced I- ) Adjustment <br /> length of line it nee ed . No . <br /> Changs Computation <br /> 8 1 Beginning Level to Thermal Higher • (c) . ( y) . Volume Minus <br /> Sensor • 1AI Low Level computc <br /> TIME E of which Beton After Product Reading Lower <br /> Contraction Expansion on - ContracExpansion tion (- ) Change per Hour <br /> 124 hr . ) PRODUCT Reading Flestored Reading Reading Recovered INFPA criterial <br /> MJJIV) — NJ7IT ) <br /> ARRIVED AT : SITE , REMOVED EROPUBEIVVAPOFRECOVERY LIN11SBLE11D REMO E . P PS , ETC <br /> SET - UP EQUIPMENT <br /> START CIRCULATION ACTOR <br /> 1ST THERMO READING 420 <br /> START 42 ' HIGH LEVEL TES <br /> 1ST HIGH LEVEL READING 1 42 <br /> 100:S CONT ' D HIGH LEVEL READING 2 42 <br /> 0 0. If If 3 42 <br /> 11 . 1 4 <br /> 42 <br /> 11 <br /> 5 42 <br /> I 1 ° 11 <br /> 6 42 <br /> 11 ° ' 7 42V lss. 8 42 <br /> ) <br /> if <br /> If <br /> DROP TO LOW LEVEL , WAIT 1 HOUR <br /> ?�� mf*� i /�o <br /> START LOW LEVEL TEST <br /> lam 1ST LOW -.11LEVEL ' READING 1 12 121 <br /> 11vPe <br /> � a� CONT ° D LOW LEVEL READING 2 12 i ` <br /> ' ° 3 <br /> 1 � lz <br /> a4� 4 12 a <br /> 1J <br /> lz <br /> rr <br /> 5 <br /> 1 /x `1 II oa <br /> 6 12 ' <br /> 7 12 <br /> if <br /> Ir 8 12 t <br /> 1ID <br /> or 10 12 <br /> - <br /> 12 <br /> 1 11 1 ° 12 1. 2 e• , It'`,-, tom <br /> 1 % ° ' <br /> -� 13 lz <br /> , r - <br /> �� ` 14 12 <br /> 1512 <br /> � r v� r1 _ <br /> `+ 16 1 <br /> r l 11 <br /> _ 17 12 <br /> 18 12 <br /> 19 12 _ <br /> 20 12 <br /> Q 0 — <br /> 11 21 12 , <br /> 22 12 <br /> . 1 <br /> 23 12 <br /> if 11 <br /> 24 12 _ <br /> STOP TEST <br /> • — 2 = ( ) GPH <br /> P - 2 . Stat <br /> T Tank Test Data Chart ement: It Is the responsibility of the owner and/or operator of this <br /> Additional Info <br /> El Tank and product handling system has been tested light system to Immediately advise slate and local authorities of any <br /> according to the Precision Test Criteria as established by Implied hazard and the possibility of any reportable pollution to <br /> regulatory agency . This Is not Intended to Indicate permission the environment as a result of the indicated failure of this <br /> / • ) G of a leak . system . The manufacturer of this test method does not assume <br /> any responsibility or liability for any loss of product to the <br /> 1 . Net Volume Change at Conclusion of Precision Test _ gph OR environment . <br /> ❑ Tank and product handling system has failed the tank lightness <br /> Signature of Tesler : test according to the Precision Test Criteria as established by <br /> regulatory agency. Tank Owner/Operator <br /> Date : <br /> OR <br /> ❑ Test Invalid due to environmental or mechanical factors beyond Date <br /> control of the testing equipment . <br />