Laserfiche WebLink
Introduction 2 to 1 Sensor lnprt Box lets <br /> Introduction2 to 1 Sensor Input Box Kits <br /> The Veeder-Root 2 to 1 Sensor Input Box is designed for use in brine filled,double wall dispenser sumps and The 210 1 Sensor Input Box is available in two kits: <br /> connects to a sump or position sensitive sump sensor installed on the base of the sump and to a mini-hydrostatic Mini-Hydro and Dispenser Pan/Sump Sensor Kit(P/N 330020-536) <br /> sensor monitoring the interstice brine.A 2-wire shielded cable is then pulled from the Sensor Input box to the TLS Contains Hydrostatic Sensor Form No.794380-304 and Sump Sensor Form No.794380-208 <br /> console and connected to one input on an Interstitial/Liquid Sensor Interface module.The Sensor Input Box <br /> permits the TLS console to increase from 8 to 16,the number of sump/hydrostatic sensor pairs that can be Mini-Hydro and Position Sensitive Dispenser Pan/Sump Sensor Kit ON 330020-537) <br /> monitored by one module. <br /> Contains Hyrdrostatic Sensor,Form No.794380-304 and Positron Sensitive Sensor,Form No.794380-323 <br /> The compact(6'x3'x2')weatherproof Sensor Input Box attaches easily to a DIN rail,rigid piping or other structural <br /> member in the sump using the included universal mounting kit Safety Precautions <br /> System Requirements <br /> The following safety symbols may be used throughout this manual to alert you to important safety hazards and <br /> precautions. <br /> • TLS-350 series console with: <br /> -ISD software enhancement module(SEM) EXPLOSIVE ELECfRICRY <br /> Fuels and their vapors are extremely expb- High vohage exists in,and is supplied to,the <br /> -V26B or later software ® sive if ignited. ® device.A potential shock hazard exists. <br /> -Interstitial/Liquid Sensor Interface module <br /> TLS-4XX console with: TURN POWER OFF WARNING <br /> -ISD feature enabled <br /> ® Live power to a device creates a potential Hes[the adjacent rson l Injury,to aurid equip- <br /> -USM Modula shock hazard.Tum es power to the dads- Q men[damage or personal Injury. <br /> end associated accessories when servic- <br /> ing the unit. <br /> Contractor Certification Requirements WEAR EYE PROTECTION INJURY <br /> ---- Fuel spray from residual preeeure in the Careless or Improper handling of materials can <br /> lines can cause serious eye injuries. O result in bodily injury. <br /> Veeder-Root requires the following minimum training certifications for contractors who will install and setup theO Always wear eye protection. <br /> equipment discussed in this manual: <br /> GLOVES READ ALL RELATED MANUALS <br /> Level 1 Contractors holding valid Level 1 certification are approved to perform wiring and conduct routing, Wear gloves to protect hands from irrita- Knowledge of all related pr000durao bolero you <br /> equipment mounting,probe and sensor installation,tank and line preparation,and line leak detector installation. ® tion or injury. ® begin work is important.Read and undaeland <br /> all manuals thoroughly.H you do not undoratand <br /> Level 2/3 Contractors holding valid Level 2 or 3 certifications are approved to perform installation checkout, a procedure,ask someone who does. <br /> startup,programming and operations training,troubleshooting and servicing for all Vesder-Root tank monitoring <br /> systems,including line leak detection and associated accessories. <br /> Warranty Registrations may only be submitted by selected distributors. <br /> Related Manuals <br /> 677013.809 Position-Sensitive Pan/Sump Sensor Installation Guide <br /> 576013.301 Sump Sensor Installation Guide <br /> 577013-838 Single Point mini-hydrostatic Sensor for Double-Wall Sumps Installation Guide <br /> 576013.879 TLS-3XX Site Prep and Installation Manual <br /> 577013-879 TLS-4XX Site Prep and Installation Manual <br />