|
MHA VERIFICATION LABORATORY ANALYSIS
<br />W 846 are. specifically noted below. Refer to the "SWRCB LUFT Field Manual", Appendix D (B), Table 3-5 on page A20 for
<br />inimum detection limits for motor vehicle fuel (gasoline and diesel). Refer to "Tri -Regional Board Staff Recommendations for
<br />nitial Evaluation and Investigation of UST's" for the waste and motor oil minimum detection limits.
<br />Detection Limits that remain below the MCL, STLC or Allowable Limit of the contaminant in question will be accepted,
<br />however laboratory shall utilize the most conservative method.
<br />LABORATORY ANALYSES TERMINOLOGY:
<br />TPH-G Total Petroleum Hydrocarbon, Gasoline, GC/FID (5030) 8015 mod or GC/MS 8260
<br />TPH-D Total Petroleum Hydrocarbon, Diesel, GC/FID (3550), 8015 mod or GC/MS 8260
<br />BTX & E Benzene, Toluene, Xylene & Ethyl Benzene, GC/PID 8020 or GC/MS 8260
<br />CL HC Chlorinated Hydrocarbon, GC/HSD 8010, GC/MS 8240 or 8260
<br />TOTAL LEAD Total lead, AA 7420, AA 7421 or ICP -AES 6010
<br />OXYGENATES MTBE, ETBE, TAME, DIPS, & TBA GC/MS 8260 (For MTBE screen only you may use.8020)
<br />METALS ICAP or AA Inductively Coupled Plasma Atomic Emission Spectrometry 6010 or Atomic Absorption Spectrometry 7000.
<br />Metals: Cadmium, Chromium III and VI, Lead, Zinc and Nickel.
<br />PCB Polychlorinated Biphenyls, GC/MS 8270 or 8080
<br />GC -FID Gas Chromatography, Flame Ionization Detection
<br />Method 3050 Acid digestion
<br />Method 3540 Soxhlet sample preparation
<br />Method 3550 Sonication sample preparation, extraction method
<br />Method 5030 Purge and trap sample preparation
<br />QA/QC Quality Assurance/Quality Control
<br />Notes: To avoid false positive detection of benzene, benzene -free solvents are to be used. Fused capillary columns are preferred to packed
<br />columns; a packed column may be used as a "first cut" with "dirty" samples or once the hydrocarbons have been characterized and proper
<br />QA/QC is followed.
<br />For drinking water sources, EPA recommends that the 500 series for volatile organic should be used in preference to the 600 series because the
<br />detection limits are lower and the QA/QC is better. Samples exhibiting any level of heavy metal contamination may require further analysis.
<br />itS-EHD recommends holding those samples until disposal is indicated.
<br />23 046 (Revised 08/13/99) Page 8
<br />OXYGFNAM
<br />NK
<br />TANK
<br />TPH-G
<br />TPH-D
<br />BTX & E
<br />CL HC
<br />TOTAL
<br />MTBE
<br />(MTBE.
<br />METAts
<br />PCB
<br />CONTENTS
<br />8015
<br />8015
<br />8020
<br />8010
<br />LEAD
<br />8020
<br />TBA,DIPE,
<br />ICRP/
<br />8270
<br />8260
<br />8260
<br />8260
<br />8240
<br />7420
<br />8260
<br />ETBE,
<br />TAME)
<br />AES
<br />8080
<br />8260
<br />7421
<br />8260
<br />or
<br />AA
<br />LEADED GAS
<br />X
<br />X
<br />X
<br />X
<br />UNL GAS
<br />X
<br />X
<br />X
<br />DIESEL
<br />X
<br />X
<br />X
<br />KEROSENE
<br />X
<br />X
<br />X
<br />UNK FUEL
<br />X
<br />X
<br />X
<br />X
<br />X
<br />PROD. OIL
<br />X
<br />X
<br />X
<br />CHLOR.
<br />X
<br />SOLVENTS
<br />X
<br />X
<br />NONCHLOR
<br />X
<br />SOLVENTS
<br />X
<br />X
<br />WASTE\
<br />X
<br />USED OIL X
<br />X X
<br />X
<br />X X
<br />All analvsis methods are the designated EPA
<br />methods described in
<br />EPA SW 846_
<br />Third Edition. Those methods not
<br />found in
<br />W 846 are. specifically noted below. Refer to the "SWRCB LUFT Field Manual", Appendix D (B), Table 3-5 on page A20 for
<br />inimum detection limits for motor vehicle fuel (gasoline and diesel). Refer to "Tri -Regional Board Staff Recommendations for
<br />nitial Evaluation and Investigation of UST's" for the waste and motor oil minimum detection limits.
<br />Detection Limits that remain below the MCL, STLC or Allowable Limit of the contaminant in question will be accepted,
<br />however laboratory shall utilize the most conservative method.
<br />LABORATORY ANALYSES TERMINOLOGY:
<br />TPH-G Total Petroleum Hydrocarbon, Gasoline, GC/FID (5030) 8015 mod or GC/MS 8260
<br />TPH-D Total Petroleum Hydrocarbon, Diesel, GC/FID (3550), 8015 mod or GC/MS 8260
<br />BTX & E Benzene, Toluene, Xylene & Ethyl Benzene, GC/PID 8020 or GC/MS 8260
<br />CL HC Chlorinated Hydrocarbon, GC/HSD 8010, GC/MS 8240 or 8260
<br />TOTAL LEAD Total lead, AA 7420, AA 7421 or ICP -AES 6010
<br />OXYGENATES MTBE, ETBE, TAME, DIPS, & TBA GC/MS 8260 (For MTBE screen only you may use.8020)
<br />METALS ICAP or AA Inductively Coupled Plasma Atomic Emission Spectrometry 6010 or Atomic Absorption Spectrometry 7000.
<br />Metals: Cadmium, Chromium III and VI, Lead, Zinc and Nickel.
<br />PCB Polychlorinated Biphenyls, GC/MS 8270 or 8080
<br />GC -FID Gas Chromatography, Flame Ionization Detection
<br />Method 3050 Acid digestion
<br />Method 3540 Soxhlet sample preparation
<br />Method 3550 Sonication sample preparation, extraction method
<br />Method 5030 Purge and trap sample preparation
<br />QA/QC Quality Assurance/Quality Control
<br />Notes: To avoid false positive detection of benzene, benzene -free solvents are to be used. Fused capillary columns are preferred to packed
<br />columns; a packed column may be used as a "first cut" with "dirty" samples or once the hydrocarbons have been characterized and proper
<br />QA/QC is followed.
<br />For drinking water sources, EPA recommends that the 500 series for volatile organic should be used in preference to the 600 series because the
<br />detection limits are lower and the QA/QC is better. Samples exhibiting any level of heavy metal contamination may require further analysis.
<br />itS-EHD recommends holding those samples until disposal is indicated.
<br />23 046 (Revised 08/13/99) Page 8
<br />
|