COMPLIANCE INFO_2004-2005 - Laserfiche WebLink

Home Browse Search

ULtULC Listed Red Thmadvft Piping System MOW GENERAL SPECIFICATIONS Pri ry Piping Secondary Containment Piping SCOPE SCOPE PIPE—Pipe shall be manufactured by Smith Flbercast by 8 PIPE—Pipe shall be manufactured by Smith Flbercast by a filament winding process using a thermosetting epoxy resin filament winding process using a thermosetting epoxy resin to Impregnate strands of continuous glass filaments which to Impregnate strands of continuous glass filaments w Nch are wound around a mandrel at a prescribed helix angle and are wound around a mandrel at a prescribed helix angle and under controlled tension. All pipe will be supplied with under controlled tension. matching tapered TA.B.Tm(Threaded and Banded)coupling and spigot ends or T.A.B.spigot spigot ends. CONSTRUCTION 3".6"PIPE—RED THREAD IIA pipe shall have continuous CONSTRUCT70N glass fibers filament wound at a 54°wind angle in a matrix 204"PIPE—RED THREAD IIA pipe shall have continuous of epoxy resin. Pipe shall be In compliance with ASTM glass fibers filament wound at a 540 wind angle In a matrix D2310 and classified by its designation code. Pipe shall of epoxy resin. Pipe shall be in compliance with ASTM meet all performance requirements and mechanical D2310 and classified by its designation code. Pipe shall properties,and shall be classified with the following meet all dimensional and performance requirements, designation codes: mechanical properties,and shall be classified with the Size Designation Code at 73.41 F following designation codes: 3" RTRP-11AF size Designation Code atT3A"F 41.6" RTRP-11AH 2"-3" RTRP-11AF 4" RTRP-11AH ITEMS 3"-6"PIPE—Glass fiber reinforced filament wound pipe with ITEMS Plain end by Plain end or TA.B.spigot by spigot ends. Pipe 204"PIPE—Glass fiber reinforced filament wound pipe with to be factory prooftested at the following pressures: matching tapered TA.B.(Threaded and Bonded)coupling 3'-300 psig(minimum) and spigot ends or TA.B.spigot by spigot ends. Pipe to be 4'-265 psig(minimum) factory proottested at the fbilowing pressures: 6'-265 psig(minimum) 2"-375 psig 3"-6"FrMNGS—Compression molded two-piece fittings 3"-300 psig shall be manufactured using a vinyl ester molding 4 -265 psig compound. The molding compound shall be reinforced with 2W FIMNGS—Compression molded fittings shall be a minimum of 60%chopped glass fiber. manufactured using an epoxy molding compound. The ADHESINS—Adhesh+e and curing agents shall be either compound shall be reinforced with a minimum of UL Listed 8000 or 7000 series adhesive. Consul Smith chopped glass fiber. Inline fittings are filament wound. Fibercast's Installation manual No.82160 for recommended ADHESINS—Adhesive and curing agents shall be either heat curing techniques. UL Listed 8000 or 7000 sales adhesive. Consult Smith Fibercast's Installation manual No.B2160 forJOINING TECHNIQUES recommended heat curing techniques. 3"-6"PIPE and FnMNGS—Pipe shall be joined with either 8000 or 7000 series adhesive. Fittings shell be joined with JOINING TECHNIQUES either 7000 or 8000 series adhesives and filler. Material to 2"4"PIPE and FITTINGS—Pipe and fittings shall be joined be Installed In accordance with Smith Fibercast's installation with 8000 or 7000 series adhesive using matching tapered manual W.B2160. bell/coupling and spigot. Material to be Installed In TES77NG accordance with Smith Fibercast's installation manual No. B2160. 3".6"SECONDARY CONTAINMENT PIPE SYSTEMS— Secondary containment pipe systems should be tested prior TES77NG to use to assure soundness of all joints and connections. 204"PRIMARY PIPE SYSTEMS—Primary pipe systems Consult Smith Fibercasfs Installation manual No.82100. should be tested prior to use to assure soundness of all joints and connections. Consult Smith Fibercast's Installation manual No.82160. Nom:6"occoridary containmcntpipc and flGings are riot UUULC uotod. 10