COMPLIANCE INFO_1985-1998 - Laserfiche WebLink

Home Browse Search

SEP 22 '97 05:52PM MARLEYW INTI 9138310207 P-9-/10 r a IQUJACKC I INSTALLATION INSTRUCTIONS FXV LEAK DETECTORS FX1V Part No. 116-056-5,FX2V Part No. 116-057-5 FX1DV Part No. 116-058-5,MIN Part No. 116-059-5 T11-414A irV dcfawl ttow me w-d ch--nuc this et—to a;ee suanmm to u e w.•rh.=*Z.n k k ru.or w:".v am m.;m m�mwndne ac tiry or the odiauee unr�+eat of s harard whish will taws anvn ua>otud jjq W!,, a ,adicate,pry�na uC�h t=ud vhidt a i(i a avn ea�rcnvadT oaraaea7 doth ar stebae+nud>++�P7 daetace i[ignated. itywy,death yr suhat tatial tKooct b damage if it�tveed. :ndiato. atahaaatd-h"heo"=W..sitsonvem!imury. , indiatntvaetalattauctiom�amw3,tiea+ .�rcati.n orma�n{�ee death tet aututsntia!Ol.peftr dnmaco if ipw.td, nanar which era imp.tsaet fist Aot rtlated to Oerre"a1 itgjuq hatardo. M:C-SEM Before installing lank detector,rgviewthe application section in leak detectormanual rslgl forlimitations; Or restrictions on usaga. • This instruction sheet should be kept with the end user of the leak detector for reference. When using 117-182 Big-Flo Diaphragm Valve,refer to installation instructions 0041-996 included.with the valve• When using an FXV model leak detector with adapter housing #038-M-5, refer to installation instructions#041.415-1 included with the housing.FXV Leak Detectors are for use with all UL-Listed 4-inch Red Jacket models containing a"P"or"AG"prefix:FE Petro UL-Listed 4-inch"STP"models;Tokheim LTL_ Listed 4-inch models—585A-3d and 585A.150. EmTampering with the screws or seals on this leak detector may inhibit operation And will void warranty. This Red Jacket leak detector is to be installed into the two- 2. Remove the two-inch plug from the top of the Red inch threaded Lapping on top of the Red Jacket submersible Jacket pump. If the two-inch plug is found to be so pump_The FXDV modelo are specially designed for use with tight that it cannot be removed, the submersible diesel fuel and should be used in diesel applications to provide should be removed from the tank and placed in a vise. the appropriate operating characteristics.For proper installa- Remove the functional element assembly next to the tion,the following steps should be followed in sequence. pipe plug. The plug should then come outreadily if elarge pipe wrench is used. Replace functional ele- wire submersible pumps to run ment assembly securely and replace the pump in the continuously.Red Jacket line leak detec- tank.(See Step 3 before replacing pump). torswiilnot perform leak testsonpumping :3, Examine straight bore below two-inch thread for systems that run continuously. corrosion roughness. If found to be rough, smooth e ieq with fine emery paper. ALL AIR MUST BE OUT OF THE SYSTEM 4. Apply UL-classified non-toxic pipe thread sealant to FOR TRE I-EAR DETECTOR TO WORK the two-inch threads on the detector. Lubricate PROPERLY.Before installingleakdatec. O-ring on the leak detector_ for in the pump, fill the system with 5. Screw the leak detector into the pump. Tighten with Product by running the pump and deliv. a wrench(top hex is 1.1/4 in.). ering product from each dispenser S. Installation of vent tube and sna to connectors. (starting with the farthest from the pump For FXZV Models p p and working to the pump)until all air is removed from system. a. Remove 1/4-inch pipe plug from tank test port in the Packer(on 6-inch Big-Flo applica- Certuin regulatory bodies require that leak detectors retrain tions,remove the 1/4-inch pipe plug from the in the system after the lines have been installed.The lines may riser/flange assembly). be purged of air by back pressuring the lines with an inert gas b. Apply a UL-classified non-toxic pipe thread such as helium or nitrogen to a pressure of 26 psi(172 kPa). sealant to the threads of the 1/4-inch NPT This may be done at the impact valve under the dispenser. straight vent tube fitting and install in tank When this pts bore has been reached,the leak detector will be test port of the packer. On 6-iach Big-Flo in the open position. By turning on the pump and gradually applications,the 1/4-inch NPT straight vent bleeding the gas from the line through a valve at the impact tube fitting may be installed into the riser/ valve of the farthest dispenser,the line may be purged of air. flange assembly. C. Apply a UL-classified non-toxic pipe thread e Disconnect power to the submersible sealant to the threads of the 1/4-inch NFT pump and relieve pressure before install- 90-degree vent tube fitting and install in the ing or removing petroleum equipment. leak detector vent opening in the cap of the 1. Disconnect power to pump at the load center. Tag or leak detector. lock out the breaker to avoid the pump being turned d Install the vent tubing into both fittings and on accidentally. tighten. 042.106-1 Aev.A 6/96