COMPLIANCE INFO_1997-1998 - Laserfiche WebLink

Home Browse Search

Mill Test External Pressure Random 7Nomilinal Nominal Nominal Nominal Wall Nominal Max.Rating(prig/MPa) Len the e") I.D. O.D. Thickness Weigght Pressure-Temp. Pressure(in./mm) (in./mm) (in./mm) (lbs:ft/kg-m) Max.Rating (psig) 75°F/24°C 150°F/66°C 2 2.235 2.375 0.070 0.4 250 psig @ 150°F 375 88 79 1 SF7.16 230 56.77 60.33 1.78 0.60 1.72 MMPa @ 66.5°C 2.59 .61 .54 4.69.1 3 3.360 3.500 0.070 0.6 175 psig @ 150°F 300 29 24 15 1 25 1 30 85.34 88.90 1.78 0.89 1.21 MPa @ 66.5°C 2.07 .20 1 .17 4.6 7.6 9.1 4 4.360 4.500 0.070 0.8 125 psig @ 150°F 265 34 30 15 25 30 0.86 MPa 110.74 114.30 1.78 1.19 @ 66.5°C 1.83 .23 .21 4.6 7.6 9.1 ® e Bending Radius,Minimum a7 � Nominal PROPERTY 2,3,4"RED THREAD•IIA Pipe Pipe Size 2" 3" 4" psi @ 75°F MPa @ 24°C psi @ 75°F MPa @ 66.5°C inches Axial Tensile(ASTM D2105) ft. 75 105 140 Ultimate Stress 15,200 104.8 13,300 91.7 Design Stress 3,800 26.2 3,325 22.9 Modulus of Elasticity 1.80 x 106 12411 1.4 x 106 9653 m 22.9 32.0 42.7 Axial Compression(ASTM D695) 33,300 230.0 25,600 177.0 Ultimate Stress 8,300 57.2 6,400 44.1 Design Stress 1.26 x 106 8687 .89 x 106 6136 (1)All values except pressure-temperature Modulus of Elasticity maximum rating are nominal values. Tolerances or maximum/minimum limits Beam Bending(SFPTM) can be obtained from Smith Fiberglass Ultimate Stress 23,000 159.0 NA NA Products Inc. Design Stress"' 2,900 20.0 1,800 12.4 (2)All sizes can accept full vacuum pressures at Modulus of Elasticity 2.18 x 106 15031 1.79 x 106 12342 maximum temperature ratings. (Long Term per ASPM D2925) (3)UL Listed 5"secondary containment piping and Non-UL Listed 6"secondary Hydrostatic Burst(ASTM D1599) containment piping are also available from Ultimate Hoop 35,000 241.0 41,000 283.0 Smith Fiberglass Products Inc. Tensile Stress (4)Ultimate and allowable design stresses are based on minimum reinforced wall Hydrostatic Design(ASTM D2992) thickness.Pipe is manufactured in Procedure A ,6, 61 10,450 72.1 compliance with ASTM D2996. Cyclic 150 x 106 (S)Design bending stress is 1/8 of ultimate to Cycles account for combined stress(i.e.bending and pressure). Coefficient of Linear 0.88 x 10.6 in./in./°F (6)For RED THREAD*ILA pipe the hydrostatic Thermal Expansion(SFPTM) 1.58 x 10 smm/mm/°C %dic design stress was determined at 150° 1 8 and 2001,Per ASTM D2992 Procedure A. Specific Gravity _ Based on this data,the extrapolated value at Flow Factor 150 75°F is 13,040 psi. Hazen-Williams Coefficient It is the policy of Smith Fiberglass Products to improve its products continually. In accordance with that policy, the right is reserved to make changes in specifications, descriptions and illustrative material contained in this manual as conditions warrant. The information contained herein is general in nature and is not intended to express any warranty of any type whatsoever nor shall any be implied. MEMeE■ Algillk A1777 L ISO 9001 aPEljSMrM 5 PRODUCTS M FTH sRA Koff VUL 14 1,11111111h, A Subsidiary of A.O. Smith Corporation - 49 2700 West 65th Street• Little Rock,Arkansas 72209-8592•Telephone(501)5684010• FAX(501)568-4465 11 jill ®Copyright 1992 Smith Fiberglass Products Inc. - - ®and Tm Trademarks of Smith Fiberglass Products Inc. - PRINTED IN U.S-A_1 SM 1194