Laserfiche WebLink
UL/ULC Listed Red Thread II A Piping System 40 <br /> REQ THREAD IIA PIPING <br /> z� <br /> RED THREAD 1IA Primary Piping RED THREAD IIA Secondary Containment Piping <br /> Nom.Pipe Pipe Nom.Pipe Pipe <br /> Size Part Length Size Part Length <br /> (InJrrm) Number (ft.) (In.1rr m) Number (ft.) <br /> z 2 50 011020-069-1 15 3 80 011030-0694 15 <br /> . y � <br /> 2 50 011020-069-2 22-25 3 80 011030-069-5 22-25 <br /> 2 50 011020-069-3 26-30 3 80 011030-069-6 26-30 <br /> 3 80 011030-069-1 15 4 100 011040-077-5 15 <br /> 3 83 011030-069-2 22-25 4 100 011040-069-5 22-25 <br /> 3 80 011030-069-3 26-30 4 100 011040-077-6 26-30 <br /> 4 100 011040-071-1 15 6 150 011060-120-5 15 <br /> 4 100 011040-069-2 22-25 6 15€0 011060-120-4 22-25 <br /> 4 1001 011040-071-3 26-30 6 150 011060-120-6 26-30 <br /> DIMENSIONAL DATA <br /> Nominal Nominal Mill <br /> Pipe Nominal Nominal Wall Nominal Pressure/ Test External Pressure <br /> Size I.D. O.D. Thickness Weight Temperature Pressure Max.Rating(prig/MPa) <br /> (tnJm t) (inJmm) (in./mm) (mJmm) (I g-m) Max.Rating (psiglmpa) 75°F124'C 150°17165°'C <br /> 2 2.235 2.375 .070 0.5 250 psig @ 150"F 375 85 80 <br /> 50 57 61 1.78 0.74 1:72 MPa 50'C 2.50 .57 _55 <br /> 3 3.360 3.500 .070 0.7 175 psig Q 150"F 300 36 34 <br /> 80 85 90 2.54 1.04 1.21 MPa @5 66'C 2.07 .25 .23 <br /> 4 4.360 4.560 _085 1.2 125 prig @ 150"F 265 34 30 <br /> 1030 111 '116 2.16 1.70 0.86 PSP a @ 66'C 1.83 .23 .21 <br /> 6 6.408 6.678 .135 2.4 NA 265 22 20 <br /> 150 163 170 3.43 151 NA 1.83 .15 .14 <br /> TYPICAL PHYSICAL PROPERTIES() <br /> PROPERTY RED THREAD'11A Pis Bending Radius,Minimum <br /> psi @ 76°F MPa 24''C psi @i 150°F MPa 56"C Nominal <br /> Pips Size 2" 3" 4" 6" <br /> Axial I ens inches <br /> Ultimate Stress 10,300 71.0 8,200 58.5 <br /> Design Stress 2,575 17,8 2,050 14.1 Ft. 75 110 140 204 <br /> Modulus of Elasticity 1.82 x 105 12548 1.42 x 105 9791 <br /> Axial Compression(ASTM D695) 33,300 230.8 25,600 177.0 m 21.3 335 42.7 82.2 <br /> Ultimate Stress 8,300 57.2 6,400 44.1 <br /> Design Stress 1.26 x 105 8687 _89 x 105 6186 <br /> Modulus of Elasticity <br /> tri SFPTM (1) A8 values except pr�rre <br /> Beam Bending( ) rating are nominal values.Tolerances or <br /> Ultimate Stress 23,000 158 0 19,200 132.0 rrommVmnimurn limits can be marred from Smith <br /> Design Stress'-'= 2,900 Ko 2,400 16"r >=ibercast. <br /> Modulus of Elasticity 2.18 x 105 15031 1.70 x 101 11721 (2) AB sizes can accept ha v pressures at <br /> (Long Term per ASTM D2925) iiwdrnum temperature ratings. <br /> (3) Ultimate arta allowable design stresses are <br /> Hydrostatic Burst(ASTM D1599) based on rrtiranum reinforced wad hdiness.Pipe is <br /> Ultimate Hoop 34 2'34 39,200 271 manufactured in compliance with ASTM 02996. <br /> Tensile Stress (4) Design bending stress is 118 of ultimate to <br /> acom"for combined Hydrostatic Design(ASTM D2992) 2"-3" 2' "s° 2"&3" 2`&' stress(i.e. and <br /> pressurq <br /> Procedure A 9,410-) 64.9`,.; 7,40 51$'' (5) Design stress is based on long term cyclic tatigue <br /> Cyclic 150 x 105 4"-6' 41-61 4"-6' 4'-6' data using ASTM D2992 test mem.Hiwevff,all <br /> Cycles 13,0405= 39.V 101450 721 testing is not compW at tirce of printing. <br /> #*Ndrostafic <br /> Coefficient of Linear 0.88 x IV inJiinJ"F cyclic t6I For THREAD)iiA s e <br /> Thermal Expansion SFPTM 1.513 X 1 blrnm"'C - stress was Prot ducened at Bas and <br /> � ( ) 2fl©°F,per ASTM 02992 A.eased on ttft <br /> data,ft extrapolated value at 75°F is 13,030 psi. <br /> Specific Gravity 1.8 (7) For RED THREAD UA pipe#Ere cyclic <br /> Floe!Factor design stress was determined at 75°and 2txi"F,per <br /> Hazen-Williams Coefficient 150 ASTM D2932 Procedure A Based on this data,the <br /> value at 15U'F is 7,4138 psi. <br /> 4 <br />