Laserfiche WebLink
01/15/2009 14:58 FAX 925 422 2748 WGMG 16002/019 <br />Michelle Henry" <br />"Willy Ng, 1/15/2009 1:5204 .0800, EVR Up <br />To: Michelle Henry" 4;mhenry@ajcehd.ccuP, "Willy Ng" <wng@sjcehd. coup <br />From: Bill Schwartz <wws@llnl.gcm:;. <br />Subject: M Upgrade -Bravo �r B-2000 Conversion OVder rorm <br />Cc-. Dawn Chase <cbase9@llnl.gov>, 'Jose M. Pinada" <pineda2@llnl.qov:)-, -Blake, Rick" <br /><blake2@llnl.gov>, "Sav Mancierill 4Mancieril@1lnl.gov> <br />Bcc: <br />Attachments: JnSWRCB-Approval-UDSCCS-2008-Bravo CONV-132000.pdf <br />AIM <br />JETok 510-3 - Wyn-Rel 267-3.pdf <br />WERS <br />Uginstall Inst ii-BravoConversionFrame-08B.pdf <br />InBravo Conversion Frame Order Form -Filled in.pdf <br />TO: Michelle Henry, Senior Registered Environmental Health Specialist <br />San Joaquin County Environmental Health Department <br />W 209.953.7699 C 209.601.2717 FAX 209.469.3433 <br />Per your request this information is being faxed to you at (209) 458-3433 in addition to being sent to <br />you by email. <br />Attached is the Bravo conversion Frame order Form, five (5) associated drawings which contain the <br />relevant dimensions, the Bravo Conversion Frame installation Instructions, and the state water <br />Resources control Board approval letter. The drawings were provided to me by the Inside Sales / office <br />Manager for S. Bravo Systems, Inc.; 2929 Vail Avenue, commarce, CA 90040 P 323-888-4133. 1 asked Bravo <br />if they would provide the letter, that you requested, that states that our now dispenser would fit on <br />the existing Bravo B2000 Under Dispenser Containment with the use of the State Water Resources Control <br />Board approved Bravo Dispenser conversion rrams, model C0NV-B2000 (CONV-82000) and I was told that <br />they do not provide such letters. <br />The 1st drawing (2510-3) is the existing Bravo Shallow pan Model #2510-3 on which the existing <br />Tokheim dispenser is installed. <br />The 2nd drawing (Dimensions & Base Layout for Dresser Wayne Reliance Series Single Remote Dispenser) <br />shove the dimensions and footprint for the now Wayne - Reliance series dispensers that will be <br />installed. <br />The 3rd drawing (8267-2_-ZUL-_a) is the 80000 single wall drawing for the Wayne dispenser showing the <br />frame and box. <br />The Ath drawing (WIAW FRAME FOR WAYNE DISPENSER BRAVO X210) is the Frame only drawing (210) for the <br />Wayne - Reliance dispenser. <br />The 5th drawing (= 9-2000) is the actual conversion Frame drawing for the 510-3 frame to the 267-3 <br />frame with offset, water splash, and bolt pattern information. <br />This information, along with the State Water Resources Control Board approval letter (attached) for <br />the Bravo Dispenser Conversion Frame, Model CQNV-82000 (MML-.D2O0) that was enclosed in the permit <br />application, shows that the proposed new dispenser will fit on the existing Bravo Under Dispenser <br />containment and is approved by the State water Resources Control Board. <br />If you have any questions, please call me at (925) 423-6626 or contact me by email. <br />Regards, <br />Bill Schwartz 1/15/2009 <br />William W. (Bill) Schwartz <br />Permits and Regulatory Affairs Division <br />Environmental Protection Department <br />Lawrence Livermore National Laboratory <br />0 <br />