Laserfiche WebLink
O <br />The 60VS Series is similar to the <br />60V Series of Vapor Line Shear Valves. <br />They are designed to break <br />at the shear groove in the event the <br />dispenser is dislodged, helping to pre- <br />vent damage to underground piping. <br />However the 60VS Series has addition- <br />al features not found in the 60V Series. <br />The 60VS Series has a F connection <br />at the inlet for dispenser piping and an <br />1 I/2" at the outlet end to accommodate <br />11/2" underground vapor lines. An air <br />test port is also included to give access <br />to the vapor lines without breaking <br />pipe joints. At the dispenser inlet end, <br />two connections are available (offering <br />a convenience of choice for installa- <br />tions). A connection through the top of <br />the valve or the side may be made. A <br />plug is shipped with the valve in order <br />to plug off the opening not used. <br />The mounting connection, below the <br />shear groove, has three drilled and <br />tapped holes for mounting to a stabiliz- <br />bar. All 60V and 60VS models have <br />all important mounting connection <br />above the shear groove as well. <br />Mounting above the shear groove is <br />important on vapor lines because of the <br />use of flexible pipe above this point. <br />The shear section must be isolated so <br />that it is the weak point in the line. <br />OPW 60VS-1000 <br />"Line Saver" <br />Same features as the 60V-1000 plus; <br />♦ 11/2" connection to underground <br />piping <br />♦ Air test port to enable vapor line <br />testing without breaking pipe <br />connections <br />♦ Choice of top or side inlet <br />connection <br />♦ Stabilizer mounting connection <br />OPW 60VSP-1001 <br />"Vapor Saver" <br />Same features as the 60VS-1000 plus; <br />Double-poppeted design helps <br />prevent vapor loss in the event the <br />dispenser is toppled <br />Vr 40.0 <br />OPW 60VSPC-1001 <br />"Vapor Saver with <br />Containment Threads" <br />Same features as the 60VSP-1000 <br />plus; <br />♦ Externally threaded on outlet <br />end for secondary containment <br />connection of underground piping <br />Materials <br />Body: cast iron <br />Discs: M-19 <br />Inlet thread size: l" NPT internal threads <br />Outlet thread size: l 1/2 internal threads <br />Ordering Specifications <br />Product No. length <br />in. mm. <br />60VS-1000 631/32" 177 <br />60VSP-1001 631/32° 177 <br />60VSPC-1001 631/32 177 <br />in. mm. <br />A 111/32' 34 <br />B 631/32° 171 <br />C 211/16' 68 <br />D 11/2 38 <br />E 227/32" 73 <br />F 111/16" 43 <br />G 215/16' 75 <br />IMPORTANT. OPW products should be used in <br />compliance with applicable federal, state and local laws <br />and regulations. Product selection should be based on <br />physical specifications and limitations and compatibility <br />with the environment and materials to be handled. <br />OPW MAKES NO WARRANTY OF FITNESS <br />FOR A PARTICULAR USE. All illustrations and <br />specifications in this literature are based on the latest <br />product information available at the time of publication. <br />OPW reserves the right to make changes at any time in <br />prices, materials, specifications and models and to <br />discontinue models without notice or obligation. <br />A, <br />11 <br />