COMPLIANCE INFO_2000-2009 - Laserfiche WebLink

Home Browse Search

SECTIA ♦ Secondary Containment Ing System Components d. If solvent is used to clean bonding surfaces, allow the cleaner to evaporate. Then apply adhesive to 40 all bonding surfaces, and insert the nipple into the line by lifting the line or moving it to one side. Pushing the pipe back into the line will push the nipple into the bell. Make certain that all tapers are tightly locked. Be careful not to cock the joint. 1.8.4 Leaking Joints Any adhesive -bonded joints that leak during pressure test- ing MUST BE REMOVED AND REPLACED. Follow the procedures shown for Fig. 1.8.6 using two sleeve couplings and pipe nipple. Upon completing any necessary repairs to the piping sys- tem, follow the proper testing sequence to verify the sys- tem's integrity. Before beginning any installation, it is important that all crew members read and be familiar with the instal- lation procedures described in this manual. The secondary containment piping system is designed for use with RED THREAD IIA product pipe. The secondary containment system consists of the next larger size pipe is and special two-piece fittings. Smith Fiberglass Products also offers a patented(1) telescoping containment pipe sys- tem that allows 100% inspection of primary piping (refer to Part Three). Many of the procedures used for installing product pipe and fittings are also used for installing secondary containment pipe and fittings. Refer to Part One for installation instructions for product pipe and fittings and to Bulletin No. F6600 for tapering tool operating instructions. Following are useful sections of Part One: Section 1 - Storage and Handling Section 2 - Layout and Preparation Section 3 - Tool and Equipment List Note: For installation of bolts, use one of the following: 1. X" variable impact wrench with W socket 2. X" variable speed drill motor with X" socket (1) U.S. Patent No. 4,805,444 (2) Band -It Banding Tool available from Band -It Idex, Inc., P.O. Box 16307, 4799 Dahlia St., Denver, CO 80216, 303-320-4555. 3. One W wrench For installing saddles, the following equipment is recom- mended: 1. Sanding equipment a. power sander with rough surface sanding disc (flex- ible pad with 40 grit or less disc), or b. hand file (coarse) 2. Fine-tooth circular hole saw with pilot drill 3. Hose clamps or Band-It(2) banding tool large enough to secure saddles to pipe. (If banding is used, the Band -It banding tool is preferred, because this tool does not leave slack in the band when the tool is removed. Two Band -It tools are recommended so that the saddle can be pulled down uniformly. Use %" (19 mm) banding. Section 5 - Cutting and Tapering (cutting) Section 6 - Installation (piping layout and trench design; adhesive mixing and curing) WENT PIPING SYSTEM im 'y containment piping Containment Pipe Size For Product Pipe Size 3" 75 mm 2" 0 4" 100 mm 3" 7S 611(3) 150 mm 4" ICI &M 2.1.2 Secondary Containment Fittings Available secondary containment fittings are tees, 90° el- bows, 45° elbows, couplings, nipples, termination fittings (with or without %" NPT threaded outlet), and saddles (belled or with NPT threaded outlets). 2.1.3 Adhesive for Secondary Containment Piping For petroleum products, alcohols, and alcohol/gasoline mixtures, use DS -8000 or DS -7000 series adhesive for in- stalling secondary containment piping systems. When joining secondary containment pipe -to -fittings and fit- tings -to -fittings, fiberglass filler must be added to the adhesive to ensure optimum performance of this type of bonded joint. Filler must be ordered from Smith Fiberglass Products. Due to the quantity of adhesive re - (3) Note: 6" (150 mm) secondary containment pipe is not UL Listed. RED THREAD IIA Pipe Sr Fittings ON 21