COMPLIANCE INFO_2020 - Laserfiche WebLink

Home Browse Search

UL/ULC Listed Red Thread@ 11 A Piping System ED THREAD IIA PIPING RED THREAD IIA Primary Piping RED THREAD IIA Secondary Containment Piping Nom. Pipe Pipe Nom, Pipe Pipe Size Part Length Size Part Length (In./mm) Number (ft.) (In./mm) Number M4 Ile 2 50 011020-069-41 15 fl%4 3 80 011030-069-4 15 2 50 011020-069-2 22-25 3 80 011030-069-5 22-25 2 50 011020-069-3 26-30 3 80 011030-069-6 26-30 3 80 011030-069- 1 15 4 100 011040-077-5 15 3 80 011030-069-2 22-25 4 '100 011040-069-5 22-25 3 80 011030-069-3 26-30 4 100 011040-077-6 26-30 4 100 011040-071 -1 15 6 150 011060120-5 15 4 100 011040-069-2 22-25 6 150 0110604204 22-25 4 100 011040-071-3 26-30 6 150 011060120-6 26 30 DIMENSIONAL DATA Nominal Nominal Mill Pipe Nominal Nominal Wall Nominal Pressure) Test External Pressure Size I.D. O. D. Thickness Weight Temperature Pressure Max. Rating (psig/MPa) (in./min) (inJmm) (in.lmm) (in./mm ) QbsJftJltg m) Max. Rating (pslg/MPa) 75°F/240C 150"F166°C 2 2.235 2.375 .070 0.5 250 psig c@ 150'F 375 85 80 50 57 61 1 . 78 0. 74 1 .72 MPa @ 66`C 2-59 .57 .55 3 3.360 3.500 .070 0.7 175 psig @ 150"F 300 36 34 80 85 90 2. 54 1 .04 1 .21 MPa @ 660C 2.07 .25 .23 4 4.360 4 .560 .085 1 .2 125 psig @ 150°F 265 34 30 100 111 '116 2. 16 1 .79 0.86 Mi-la @ 66"C 1 .83 .23 .21 6 6.408 6.678 .135 2.4 NA 265 22 20 150 163 4 170 3. 43 3.51 NA 1 .83 . 15 . 14 TYPICAL PHYSICAL PROPERTIES(3) PROPERTY RED THREAD° IIA Pie Nominal Bending Radius, Minimum psi @ 76°F MPa @ 24 "C psl @ 150°F MPa @ 66°C Pipe Size2" 3" 4" 6" Axial ensl a inches Ultimate Stress 10,300 71 .0 8,200 96.5 Design Stress 2 575 i7.8 2,050 14. 1 Ft. 75 110 140 204 Modulus of Elasticity 1 .82 x 106 12548 lA2 x 106 9791 Axial Compression (ASTM D695) 33300 230.0 25,600 177.0 m 21 .3 33 .5 42.7 622 Ultimate Stress 57,2441 Design Stress 8 300 Modulus of Elasticity 126x 106 868fi86 400 7 .89 x 106 613136 Bending (SFPTM) (1) All values except pressure-temperature Beam Ultimate Stress 23,000 1�i9.0 19,200 132A m;Wmum rating are nominal values. Tolerances or Design Stress(4) 2 900 20 .0 2,400 16. 5 nFibeircas vmirdmum OrtxTs can be obtained from Smith Modulus of Elastici(y 2. 16X 106 15031 1 .70 x 106 11721 (2) Ali sizes can accept full vacuum pressures at (Long Term per ASTM D2925) maximum temperature ratings. (3) ultimate and allowable design stresses are Hydrostatic Burst (ASTM D1599) based on minimum reinforced wait thickness. Pipe is Ultimate Hoop 34,000 234 39,200 271 manufactured in compliance with ASTM D2996. Tensile Stress (4) Design bending stress is 118 of ultimateto account Hydrostatic Design (ASTM D2992) 2" - 3" 2% 3" 2"& 3" 2% 3" pressu e1°r combined stress (i.e. bending and Procedure 91410161 ti1. 9 '' 71400m 5)Jol (5) Design stress is based on long term cyclic fatigue Cyclic 150 x 10, 4" - 6" 4"M . V 4U . 6" 4" - 6" data using ASTM D2992 test method. However, all Cycles 13,040r6j 89. 9 ' 10,450 72. 1 testing Is not complete at time of printing. 0.88 x 1 Da in.Cnl°F (6) For RED THREAD IIA pipe the hydrostatic Coefficient of Linear cyclic design stress was determined at 150° and Thermal Expansion (SFPTM) 1 .58 x I ON'mm/mm/'C 2002F, perASTM D2992 Procedure A Based on this data, the extrapolated value at 75°F is 13,030 pst. Spode Gravity 1 .8 (7) For RED THREAD IIA pipe the hydrostatic cyclic Flow Factor design stress was determined at 750 and 2D0°F, per HazenVilliamsCoeffcient 150 ASTM D2992Procedure A Based on this data, the extrapolated value at 150°F is 7,400 psi. 4 i I i