Laserfiche WebLink
LJ <br />OPW EVR Thread -on or OPW/POMECO; <br />certified for installation on OPW Phase I EVR systems. All fill <br />feature enhanced 1DK-2100-EVR vapor tight drain valves thal <br />a maximum vapor leak rate of 0.17CFH at 2.0 inches H2O.' <br />feature, a permanent plug installed in the drain ports as per <br />uirements. <br />tion Valves are 'certified ;for <br />Ys,re designed to provide <br />S,`EPA requirements, <br />ilefloat pt and a <br />threaded lower tube erection And excee'the EVrq r�ierat for.tttax�mEtrri°vapor leak <br />rate of 0.17CFH at 2.0 des H2O. The 61 SMR si row f the OPW <br />EVR spill container witkAhe patent pending 61JSK Jack Scre-'� ►1tt ation allows <br />liquid in the spill conf�erto be drained directly into the drd`tube, thereby )Su ing the drain <br />valve from the tank ulle, eliminating a notorious leak point in previous systems. <br />Wftt The OPW/POMECO 6111-1400 Tank Bottom Protector is EVR certified` <br />Wrl'allation at the bottom of the overfill prevention valve drop tube to help prevent the <br />v rground storage tank from sustaining damage from erosion or tank gauging sticks. <br />The OPW 53VML Ball Float, 233ailed <br />61T Fill Drop Tube configuration can be installed as an alternative�150 , <br />Overfill application.; The installation of the Ball Float/Drop Tube*;tem is <br />identical to the 61 SO Overfill valve on Phase 1 Vapor Recovery Systems. <br />Q ,W R Rot�taW---Swivel<Ada tors 4r��cgrtifjd <br />for installation on the fill and vapor ports on �r"r Swwel Adaptors' <br />from loosening on the spill container risers � OM a'EVR"req't cement to <br />maintain a minimum 360 -degree rotation with artt3irque nQt ko.excee 108 inch <br />pounds (9 foot pounds). The enhanced po et OPW 61VSA-EVR vapor swivel <br />adaptor provides, a vapor fight seal when closed, per equirements. <br />'adaiptor Tool - An OPW 61 SA TOOL Adaptor installation tool is required to ensure proper <br />installation of QPW Rotatable Swivel Adaptors, spill containers and threaded riser adaptors, per <br />EVR requirements. The 61 SA -TOOL includes provisions for the use of a torque wrench to facilitate <br />accurate installation and testing. <br />per EVR requirements. <br />ation on <br />feature <br />)le-tigght <br />nodels. <br />e� Miser Adaptor (Face Seal Adaptor) - An OPW FSA -400 Threaded Riser Face Seal <br />Adaptor is required to provide a flat, true sealing surface on threaded pipes where a gasket seal <br />exists per EVR requirements. The FSA -400 is installed on the fill pipe riser below the spill <br />, - W -n container to provide a true sealing surface for the drop tube flange on the 61 SO-40OC-EVR <br />overfill prevention valves. The FSA -400 is also required on tank gauging risers, though is optional <br />on vapor risers and rotatable adaptors, <br />Pressure Vacuum Vent - The OPW 623V Pressure Vacuum Vent is certified for installation on the <br />OPW Phase 1 EVR System. The 623V`s are installed on top of the vent pipes for underground <br />fuel storage tanks. The vent cap and internal wire screen are designed to protect the tank vent <br />lines against intrusion and blockage from water, debris or insects. A normally closed poppet in <br />the valve opens at a predetermined pressur&or vacuum setting to allow the tank to vent. The <br />623V exceeds the EVR requirement of a maximum vapor leak rate of 0.17CFH of 2.0 inches H2O. <br />• <br />"'�rcrs�t <br />9393 Princeton -Glendale Road •Cincinnati, Ohio 45011 • Tel: (800) 422-2525 • Fax: (800)`421-3297 • www.opw-fc.com <br />2003, OPW Fueling Components P1 EVR-8/03-5M <br />