COMPLIANCE INFO_2013-2018 - Laserfiche WebLink

Home Browse Search

O O 00 d z U vi .. U a 10 1/2" PRESSURE VACUUM VENT 1" FIRE RATED, 0 CAPS STAINLESS STEEL q Q' U FLEXIBLE CONNECTOR UNISTRUT 2" GALVANIZED UNION & NIPPLES 1" GALVANIZED VENT PIPING MIN, SLOPE VENTS SUPPORT b O ti U PER FOOT, 100FT, MAX LENGTH. MAX. DISTANCE BRACKET CFC 2010 §2206.7.9.2.2 LOCATION WITH a> WITHOUT PIPE SUPPORT NOT TO EXCEED 10', VAPOR-PROCESSING EQUIPMENT SHALL BE LOCATED AT OR 2" GALVANIZED SAME ELEV. AS U W U ABOVE GRADE. SOURCES OF IGNITION SHALL BE LOCATED NOT TEE TOP OF P V VALVE LESS THAN 50 FEET (15240mm) FROM FUEL-TRANSFER AREAS AND NOT LESS THAN 18 INCHES (457.2mm) ABOVE I FLOAT CHECK VALVE AIR BREATHER ASSEMBLY P/N 9948 TANK FILL OPENINGS AND TOPS OF DISPENSER ISLANDS, P/N 9468G 12' MINIMUM ABOVE GRADE VAPOR-PROCESSING UNITS SHALL BE LOCATED NOT LESS OVERFILL PROTECTION THAN 10 FEET (3048mm) FROM THE NEAREST BUILDING OR 2"X1" REDUCER BUSHING PROPERTY LINE OF A PROPERTY WHICH CAN BE BUILT UPON. 1" BLADDER VAPOR INLET ASSN. EXCEPTION: WHERE THE REQUIRED DISTANCES TO SIPHON BUILDINGS, PROPERTY LINES OR FUEL-TRANSFER AREAS 2" GALVANIZED ELBOW y CANNOT BE OBTAINED, MEANS SHALL BE PROVIDED TO — --- — TEE W/ PLUG PROTECT EQUIPMENT AGAINST FIRE EXPOSURE. ACCEPTABLE MEANS INCLUDE: 1. APPROVED PROTECTIVE ENCLOSURES, WHICH EXTEND AT SIPHON TUBE ADAPTER STAMP LEASE 18 INCHES (457.2mm) ABOVE THE EQUIPMENT, CONSTRUCTED OF FIRE-RESISTANT OR NON-COMBUSTIBLE MATERIALS OR - 2. FIRE PROTECTION USING AN APPROVED WATER-SPRAY SYSTEM. HEALY CLEAN AIR SEPARATOR CONTRACTOR SHALL CONFIRM AND LABEL VAPOR-PROCESSING EQUIPMENT SHALL BE LOCATED A ALL VENT STACKS WITH CORRECT AIR MINIMUM OF 20 FEET (6096mm) FROM DISPENSING DEVICES. PRODUCT VENT TIE IN BALL VALVE TO AVOID PROCESSING EQUIPMENT SHALL BE PROTECTED AGAINST PRODUCT CONTAMINATION AND rr r l SIPHON TUBE LOCKED OPEN PHYSICAL DAMAGE BY GUARDRAILS, CURBS, PROTECTIVE IMPROPER PROCESSOR TIE-IN. i ENCLOSURES OR FENCING. WHEN APPROVED PROTECTIVE PROVIDE CONFIRMATION ON PIPE AND OR I , ENCLOSURES ARE USED, APPROVED MEANS SHALL BE TANK CHECKLIST (LABEL MAKER OK). IN NORMAL I !! �� 400 GALLON BLADDER, PROVIDED TO VENTILATE THE VOLUME WITHIN THE ENCLOSURE OPERATION TO PREVENT POCKETING OF FLAMMABLE VAPORS. ' ��1 ' VAPOR HEALY CLEAN AIR SEPARATOR IF A DOWNSLOPE EXISTS TOWARD THE LOCATION OF THE o i .j (36" O.D. X 93" E.G.) VAPOR-PROCESSING UNIT FROM A FUEL-TRANSFER AREA, ae. THE CHIEF IS AUTHORIZED TO REQUIRE ADDITIONAL r m BALL VALVE tl) SEPARATION BY DISTANCE AND HEIGHT. o LOCKED CLOSED I �i— CFC 2007 §2206.7.9.2.3 INSTALLATION a OR 3 704 PLACARD Q._ VAPOR-PROCESSING UNITS SHALL BE SECURELY MOUNTED ON CONCRETE, MASONRY OR STRUCTURAL STEEL SUPPORTS ON oIN NORMAL CONCRETE OR OTHER NON-COMBUSTIBLE FOUNDATIONS. o �� OPERATION 5 y ¢ _ 5 >C v a a Y/) uCT v iw 2" SCH. 40 GALV. STEEL a. O1 VENT RISER PAINT TO BALL VALVE "NO SMOKINVFWAABLE VAPORS" Q A z MATCH SITE CONDITIONS LOCKED CLOSED SIGN WITH 3 HIGH LETTERING ON i/ r/ m E o OR CONTRASTING BACKGROUND FRONT VIEWOOF BOLLARD V o w O FASTEN VENT RISER TO FRAME W/ NOT SHOWN IN THIS VIEW _ 2" BRONZE U-BOLT, 3/8"0 HOLE IN NORMAL SIPHON TUBE FOR CLARITY. b W/ LOCK WASHER HEX NUT. TEST OPERATION 9 _ LV IJ EACH RISER FOR ELECTRICAL 400 GALLON BLADDER, o ¢ 2" SCH, 40 GALVANIZED STEEL RISER. CONTINUITY TO VENT RACK (TYP.) IZ STRAIGHT PIPE BOLLARDS, PAINT PER SPECS (TYP.) 2" TEE WITH 1/4" TEST LOCATION BASED ON SITE H - PORT FITTING AND 1/4' " CONDITIONS r 2" TEE WITH 1/4" TEST PORT PLUG (TYP.) c9i FITTING AND 1/4" PLUG (TYP.) BOLTED GROUND CONNECTION TO I i v1 O VENT RACK. JUMPER Y4 AWG BARE G STRANDED CU FROM,STAND ALONE Ba;"-1 SENSOR i i , ! ; BOLTED GROUND CONNECTION MOUNTING RACK TO HEALY TANK BASE. ¢ EXPLOSION PROOF J-BOX EXPLOSION PROOF J-BOX / / 8" 2,500 PSI I MOUNTED TO POST MOUNTED TO POST FAIR I I � I( VAPOR � CONCRETE TANK BOLTED GROUND CONNECTION TO SEAL OFFS SLAB. 2-IN-1 SENSOR VENT RACK. JUMPER q4 AWG BARE Tn "`� BOX STRANDED CU FROM STAND ALONE \\� p4 AWG BARE STRANDED CU MOUNTING RACK INSTALL (1) 1" CONDUIT PLUG \` GROUND WIRE. ROUTE TO MANOMETER SEAL OFF FUTURE LTANKEDI GNOSTIC (FOR ( SEE TANK FIELD GROUNDING HOUSING REQUIREMENTS ROUTE TO BELOW) SYSTEM. C HYDROSTATIC MONITOR SENSOR -- k4 AWG BARE STRANDED CU ° __ -- 6®® , ° MONITORING PANEL IN — 15"0, 2,500 PSI 2 FOR DOUBLE WALL VENT III GROUND WIRE TO TANK FIELD BUILDING TRANSITION CONTAINMENT SUMP GROUNDING SYSTEM 23" CLEAR CONCRETE --- GRADE _ - ___-_ --- GRADE a FOUNDATION TYP. 2" BELL.MALE ADAPTER /\� I I'\//�//�//\//\//\% a4 CWiG BARE I GROUND WIRETOr \ II B ✓ // // // // // /� P d ° ° DRAI�bENSATE° O /� W _-- II ( /��/��/��/\�/��% TANK FIELD GROUNDING 3" FRP BONDED FITTING \ r� - - III -- / / / / / SYSTEM d Q ° d PE.R.f GEOTECHN°ICALL REPaOdRT d W/ TEST PORT (TYP.) SUBBASE OPTIONAL 6" THICK CONCRETE SLAB 2" INSIDE 3" DOUBLE OPTIONAL 6" THICK INTRINSICALLY SAFE d <... WALL FRP VENT LINE. ILII ° CONCRETE SLAB HYDROSTATIC MONITOR SENSOR U 4 -� WIREWAY IN BUILDING 'i+' - a .`°''+ °'G SLOPE TO TANK AT 1/4" ° i- 12"0.2500 PSI FOR DOUBLE WAIL VENT I . d I - d ;•� ° ° r PER FOOT MINIMUM. CONCRETE RACK TRANSITION CONTAINMENT SUMP /�11B RA E �E G�OTECMNICAL \PORT / / / (VACUUM MONITORED) FOUNDATION LIQUID SENSOR �� /\\\` \ \ \ \ L-- 2" FLEX CONNECTOR n1 ' ' 16® m-== _-__®® ==J NON-DISCRIMINATING \/\ \/\ J �,/�./ - -- 2" FLEX CONNECTOR (TYP.) / / / / '.a 4"z3" CONCENTRIC ;��i��i /�i��;��; ` ( .) ` `° r FRONT ELEVATION ;�` ` BRINE FILLED DOUBLE 2" INSIDE 3' DOUBLE WALL /\� ° REDUCER (TYP.) \/�\/ /,\��\/�\/ LIQUID SENSOR WALL VENT LINE FRP VENT LINE. SLOPE TO / NON-DISCRIMINATING TRANSITION SUMP TANK AT 1/4" PER FOOT \\ ��/ LTJ MINIMUM. (VACUUM MONITORED) ° / ° W W BRINE FILLED DOUBLE WALL VENT LINE 42" ' I � TRANSITION SUMP ° ��VE SOILF 15 �r (f) C) COMPACTED OR NATIVE SOIL \ COMPACTED OR NA(TYPICAL) %\/ ° ° - //\ w H Ln (TYPICAL) FRONT ELEVATION //N//\��/��! U Of SIDE ELEVATION w W > a � � = rn O ON (V N MW VENT RISER DETAIL W/ EXISTING HEALY TANK DRAWN 6Y: REVIEWED BY: DY DATE: 7.26.18 _ SCALE: N.T.S. SHEET F -3