Laserfiche WebLink
SECTION -6' i Installation <br />`ILE 1.6.2 Adhesive Kit Data <br />•7000 Series <br />• For Petroleum Products in all Piping Systems <br />• For Petroleum Products, Alcohols, and Alcohol -Gasoline Mixtures in Secondary Containment Systems <br />Approximate No. of Bonds per Kit <br />Working <br />2" 3" 4" <br />Life(1) <br />Kit(2) <br />Quantity Mixed Adhesive <br />(50 mm) (75 mm) (100 mm) <br />(Min.) <br />DS -7014 <br />6.8 oz. (193 g) <br />25 18 10 <br />25 <br />DS -7024 (twin pack) <br />2.5 oz. ea. (71 g ea.) <br />18 10 6 <br />25 <br />DS -7069(3) <br />9.95 oz. (282 g) <br />— — — <br />25 <br />DS -8000 Series <br />• For Use with RED THREAD IIA Pipe and Fittings or RED THREAD IIA Secondary Containment Fittings <br />for Petroleum Products, Alcohols, and Alcohol -Gasoline Mixtures <br />Approximate No. of Bonds per Kit <br />Working <br />2" 3" 4" <br />Life(1) <br />Kit(2) <br />Quantity Mixed Adhesive <br />(50 mm) (75 mm) (1.00 mm) <br />(Min.) <br />DS -8014 <br />6.4 oz. (181 g) <br />21 is 8 <br />15 <br />DS -8024 (twin pack) <br />2.7 oz. ea. (77 g ea.) <br />18 12 7 <br />15 <br />DS -8055 (bag kit) <br />1.6 oz. (45 g) <br />6 4 2 <br />15 <br />DS -8069(3) <br />9.3 oz. (264 g) <br />— — — <br />15 <br />51) <br />(1) Working life is the time it takes a properly (2) Solvent does not come with the adhesive kits; (3) Not recommended for 2", 3', and 4" (50 mm. <br />' can of adhesive to "set up" at 757. it must be ordered separately. 7S mm, and 100 mm) installations because of the <br />ger of bonds is based on the volume in the large quantity of adhesive per kit. " <br />Idt and must be completed within the working + <br />Iife of the kit. <br />• Cut off contaminated surface and replace with a new <br />taper or sleeve coupling. <br />• Wire bushes may be used for cleaning T.A.B. surfaces; <br />however, they must be clean and free of oily contami- <br />-ltion. <br />• Dirt contamination can be removed by water washing. <br />Be sure the surfaces are dry before bonding. <br />10 <br />Note: Using solvent as a cleaning method is optional. <br />If preferred by the customer; use solvent. 1,1,1 <br />trichloroethane solvent is available from Smith <br />Fiberglass Products. Some alternate cleaning solvents <br />available through local hardware or industrial supply <br />houses are acetone, alcohol, methylene chloride, and <br />methyl ethyl ketone. After cleaning, be sure any resid- <br />ual solvent has evaporated before applying adhesive. <br />DO NOT USE SOLVENTS THAT LEAVE AN OILY <br />FILM ON THE BONDING SURFACES. <br />WARNING: <br />Some de- <br />greasers and <br />solvents are <br />extremely <br />flammable. <br />Be sure to read <br />warning labels <br />on containers. <br />Never use <br />gasoline, tur- <br />pentine, or <br />diesel fuel to <br />clean joints. <br />FIGURE 1.6.5 <br />Installation Instructions <br />