Laserfiche WebLink
i <br /> I <br /> MS ENV FEB3075 <br /> For Environ Miniature Series 3075A Conduit repairs <br /> I <br /> Page 2 - <br /> Step 8: install The Eccentric Insert&Multi-Sync Reducer <br /> STEP 7:Install&Bond Eccentric Insert&Multi- Dry fit the Eccentric Insert.Make sure it fits properly _ <br /> Sync Reducer Back Together over the pipe&inside the sleeve. - <br /> • Wrack Eccentric Insert around the pipe Dry fit the Multi-Sync Reducer <br /> • Wrack Multi-Sync Reducer around the pipe Adjust the positions so that they lineup properly with S <br /> • Apply DBB III to split area on Eccentric Insert, the Repair Sleeve&Pipe. <br /> press ends together&clamp Note:A proper fit will not cause extra pressure or force to <br /> f <br /> • Apply DBB III to split area on Multi-Sync the sleeve and will allow a longer lasting repair, <br /> Reducer,press ends together&clamp Once you have the part lined up correctly <br /> 1.Pull back the Multi-Sync Reducer&Eccentric Insert <br /> _ 2.Apply DBB III bonder all around the Eccentric Insert' <br /> - 3.Slide Eccentric into the Repair sleeve in the proper <br /> position <br /> 4.Apply DBB IiI bonder all around the Mufti-Sync ,+i <br /> Reducer <br /> - - 's proper lace _ <br /> - - 5 Slide the Multi-Sync Reducer Into itp per p <br /> 6.Set the Clamp the around the sleeve&over the <br /> Eccentric Insert and tighten"snugly". <br /> 7.Set clamp over reducer end on the pipe&tighten <br /> enough to create a seal around the pipe. <br /> Parts are wracked around the pipe <br /> : ;I�gT �r�gpBtr Cor�i�Qnen�{`k�PP P diclil�$+"N�h PcrBeitdlcu��p�ng entriesjn Dire�B,uriei Cottduihappil�tf4ns. <br /> se�F:StIX&-`fix iufct� �EIE Pipe OD <br /> Inches lRepair Kit Product Number Clam Sire LF 11 Fill oz. <br /> FEB-3075 for 3/4'GeoFfex Q Pie 1.18 Consult Facto 20 13 i <br /> FEB-3075 for 3 4° <br /> Rigid Conduit 1-05 MSZ ENV FE8 3157 16 14 <br /> FEB 3050 for .Rigid Conduit 0.84 MSZ ENV FEB 3050 16 14 <br /> Parts are bonded&clamped <br /> f <br /> step 10: Fill With DBF II,Insert Fill Plug TOOLS REQUIRED: <br /> • Assemble DAG&DBF Ii(see instructions on DPM website). Gloves and Static Mixer <br /> • Purge a maximum of 2 oz. 5/16"Nut driver (for Band Clamps) I <br /> • Fill fitting slowly. _ - DAG Caulk Gun (for DBF 11) <br /> • insert fill plug when filling is completed. _ DAGP Caulk Gun (Pneumatic version for DBF 11) <br /> • Clean any spilled DBF 11 with DBC and dispose = = DAG III Caulk Gun (for DBB V) <br /> of remaining products per local requirements. _=- <br /> - PRODUM NEEDED: <br /> Note:After 1 hour DBC Cleaner Each DBF 1I 11 DBB V come <br /> the repair job may be <br /> DBB Ill Bonder with a Static Mixer i <br /> hydro-static tested _ DBF II Polysulfide Liquid Fill <br /> DBB V Bonder(for Poly or Fiberglass sumps) <br /> - Flt L Volume• (Der repair boot) <br /> Volume of DBF 11 needed = 14 Oz <br /> Volume of DBB iII needed = 1/2 Oz <br /> Volume of DBB V needed = 9 ML <br /> Remote Fill Option: <br /> The following parts are available to order if you can not Parts in kit: <br /> properly position the assembled DBF ii applicator gun to Bonding Ring UiZ-M5-3.5x1.8-1.80 <br /> Sleeve u5z-3.5x3.5 <br /> "fill"the repair. The Remote Fill parts provide a flexible <br /> Eccentric Insert UIZ-3.5x2.6E <br /> extension for the filling process. Multi-sync Reducer URZ-2.6x1.1 <br /> RF Adapter 24"tube with male&female ends 5 clamps 3#60,1#40,1#16 <br /> RFA Tube-24 'h"Tubing in 24"lengths Fill Port Plug RFAxPlug <br /> RFA Tube A"Tubing in 200'length roll Install Instructions <br /> RFA TubexTube "Tube Coupling <br /> RFA xFemale "Tube-Female Fill Port end <br /> RFAxMale 'r4"Tube-Male Fill Port end <br /> RFA xPlug W Tube-Male Plug for fill port <br /> Diversified Products Manufacturing Inc.Environ Repair Manual Full Version Rev 3 Page 56 of 70 <br />