Laserfiche WebLink
0 <br />RAPID0 6 <br />T CONTAINMENT PIPING <br />SECTION <br />TERMINATION <br />Termination at the storage tank <br />is accomplished using a termina- <br />tion fiIIit)), with a 14" fcmalc NIT <br />threaded outlet (see Fig. 6). <br />'Termination at the dispenser <br />may be accomplished using a ter- <br />mination fitting with or without <br />the %' NP'F threaded outlet (see Fig. <br />9). '1 o facilitate ease of terminat- <br />ing, special hell x reale adapters or <br />Special sleeve couplings (which <br />have been machined to fit the sec- <br />ondary containment fittings) are <br />available for Its(, with secondary <br />Fiberglass <br />Threaded Adapter <br />(Bell x Male) <br />i <br />Flexible ® e <br />Connector <br />Figure 9 <br />containment termination fittings. <br />Refer to 'fable :3 and Figs. 6 and <br />7 for additional information on <br />terminating the system. <br />SECTION <br />CONTAINMENT <br />CROSSOVER <br />Wheal installing a Smith <br />Fiberglass Products containment <br />system, some preparation is neces- <br />sary if the closest possible separa- <br />tion of lines is required. You need <br />to shorten otic leg of the 45° con- <br />tainment elhow and the side run <br />of the containment tee. <br />Refer to I'ablc 4 for the maxi - <br />nnunn length that you can remove <br />and for the minimum nipple <br />length of both product piping and <br />containment piping. <br />'Fo prevent interference of the <br />pipe lines, do not locale two con- <br />tainnncnt fittings closer than <br />shown in Fig. 10 on page 6. <br />Table 3 <br />Teri-nination Fittings Connections <br />Termination Small End fits: <br />Fitting Size (ill.) Large End Fits: (one piece secondary containment <br />fittings with scarfed O.U.) <br />3x2 <br />(4" to 2")(1) <br />4 x 3 <br />6 x 4 <br />3" Pipe <br />2" BxM Threaded <br />Remove from <br />Adapter or Coupling <br />4" Pipe <br />2" BxM Threaded <br />45° Crossover Ell <br />Adapter or Coupling <br />4" Pipe <br />3" BxM Threaded <br />(in.) <br />Adapter or Coupling <br />6" Pipe <br />4" BxM Threaded <br />(min. in.) <br />Adapter <br />Note: :111 olher acwndan containment fittings are manufachned to fit the 0.1), of <br />containment pilling <br />(' 1M en Icrminatin}; from V secondary containnenl pipe to _"' product pipc. refer to <br />I ig. 7. You rcilf need a !" x V termination fittingwith or without tap, a T' x 2" sec- <br />oll&m crmlainnrcnt reducer bmhing, and a 2° hell x male threaded adapter for sec- <br />ond;m rontainnent ora one-piece 2" coupling for sccondan' containment (scarfed <br />o.11.l. <br />mm <br />Containment <br />Remove from <br />Remove from <br />Product(z) <br />Containment <br />Pipe Size <br />45° Crossover Ell <br />Side Run Tee <br />Nipple Size <br />Nipple Size <br />(in.) <br />(max. in.) <br />(max. in.) <br />(min. in.) <br />(min. in.) <br />3 <br />1'/ <br />1% <br />2 x 8 <br />3 x 6 <br />4 <br />2 <br />1X <br />3 x 8 <br />4 x 6 <br />6 <br />1% <br />1 <br />4x 10 <br />6 x 8 <br />O)A01 al len};Ih of the product nipple will s:ue sfi,ghtfy hecause of different insertion lengths due to variations in tapers. <br />5 <br />