Laserfiche WebLink
125 U THIRD-PARTY CERTIFIED UST LININGenviroline, <br /> ON- <br /> Enviroline"125U is a 100%solids reinforced epoxy novolac lining designed for underground storage tanks <br /> (UST) that must meet API 1631. Enviroline 1250 exceeds industry specifications for UST's to meet <br /> mandated federal and state corrosion protection standards. <br /> IYPICAUbE Internal tank lining for steel, fiberglass and concrete underground storage tanks, above ground <br /> petroleum storage tanks,secondary containment areas,and other aggressive containment vessels. <br /> BENIM -Gasoline and gasohol resistance -1001%methanol and ethanol resistance <br /> -Excellent adhesion -Thick-film,single coat application(100-125+mils) <br /> -10 or 20 year warranty offered -Fast curing(Immersion service in 10-12 hours) <br /> -Third-party tested and certified -Meets API 1631 requirements for lining UST's <br /> UMRASMOFUSE See Enviroline Chemical Immersion Resistance Guide for exposure requirements or consult your Enviroline <br /> representative. <br /> DATA Weight(lbs/gal):11.4 Pot Life(@100°F):12 minutes <br /> Volume Solids:100% VOC(mixed lbs/gal):0.18 <br /> Color(s):Green,White VOC(mixed g/1):21 <br /> Hardness(Shore D min.):75 Flash Point:>200°F <br /> Recommended Thickness:40-80 mils DFT(100-125+mils DFT to meet API 1631 UST requirements) <br /> Temperature Resistance- <br /> Non-Immersion,Dry Heat:300°F(149°C) <br /> Continuous immersion temperature resistance is dependent on particular reagent exposure. See <br /> Enviroline Chemical Immersion Resistance Guide or consult Enviroline representative. <br /> COVERAGE Theoretical Coverage*:1604 sq.ft per gallon @ 1 mil dry <br /> @ 40 mils:40 sq.ft.per gallon <br /> @ 80 mils:20 sq.ft.per gallon <br /> @ 100 mils:16 sq.ff.per gallon <br /> @ 125 mils:13 sq.ff.per gallon <br /> 'When ordering product, make allowances for any loss due to overspray, surface irregularities, etc. <br /> (approx. 15-20%). <br /> DRY&CURESCHEDULE ing schedule at temperatures indicated and 50%relative humidity: <br /> 55.F 77-F e <br /> Touch Dry 7 hours 2 hours 1 hour <br /> Dry Hard 12 hours 3 hours 2 hours <br /> Minimum Recoat 11 hours 3 hours 2 hours <br /> Maximum Recoot 18 hours 5 hours 3 hours <br /> Cure 30 hours 12 hours 7 hours <br /> Post Curing: Enviroline 1250 may be post cured to expedite curing or increase chemical resistance <br /> for extremely aggressive environments.Post cure for a minimum of 2 hours at 250OF or 6-8 hours at 150°F <br /> for maximum resistance. Consult Enviroline Technical Services Department for specific application <br /> information. <br /> SURFACEPRE'ARARON All surfaces must be clean,dry and free of dust, dirt,oil or other foreign matter.Steel surfaces shall be <br /> abrasive blasted to SSPC SP-5/Noce No. 1 White Metal finish with a minimum 3-5 mil angular profile for <br /> best results. Concrete shall be abrasive blasted or etched with 10%muriatic acid. Enviroline 54 or 58 <br /> Primer recommended for concrete surfaces. <br /> Plural component equipment is highly recommended for application.Utilize a pump with a 2:1 mix ratio <br /> and GRACO 45:1 or greater power ratio. Also needed are two 91A" long x 3/8" inside diameter x 12 <br /> element static mixers which are available from Graco.Heated tanks and heated lines up to 150°F may <br /> be necessary. The resin fluid line should be 1/2" ID minimum, the hardener fluid line should be 3/8" ID <br /> minimum,and the high pressure solvent fluid line should be 1/4"ID minimum.A reversible tip(.031 -.043) <br /> is suggested.Keep in mind that plural component application requires volumetric check of the mix ratio <br /> (utilizing a ratio monitoring system)before and during the application process. Any variation in product <br /> color during application will indicate the plural pump is off ratio. <br /> INDUSTRIAL ENVIRONMENTAL COATINGS CORPORATION dba ENVIROLINE GROUP <br /> 1831 BLOUNT ROAD, POMPANO BEACH, FL 33069 • (800) 449-6525 • FAX (954) 978-3913 e WWW.ENVIROLINEGROUP.COM <br />