COMPLIANCE INFO_1993-1998 - Laserfiche WebLink

Home Browse Search

Extractor � OPW The OPW 233-E Extractor fitting is for use with any 11/2" foot valve with a maximum outside diameter of 23/4". The 233-E has 4" male thread for con- nection to 4" tank flange and is gas- ket -sealed to prevent loss of prime, caused by air being sucked in through the top fitting. Materials Body: cadmium plated cast iron Cap and suction stub adaptor: bronze Gasket: chromed tanned leather SIZE: 11/2" WT.: 20.22 lbs. 233-E-4040 The OPW 233-P Extractor fitting has internal threads to accept a co sting nipple between the extr he tank flange, whic son to adjust the t 3-P in relatio a cage of the 2 placed because it is t I - it is simply lifted out like a Materials Body: cast iron Cage: bronze Seals: bung -N O-ring SIZE: 2" WT.: 18.00 lbs. 233-P-6050 The OPW 233-V Series Extractors are used to hold and position the OPW 53-V Series Float Vent Valves in the underground storage tank. It is furnished complete with an extractable cage. The entire Float Vent sub -assembly can be extracted from the tank by using either an OPW 52 or 89 Extractor Wrench for tank testing. The OPW 233-V extractor is a single outlet extractor used in non-manifolded vapor recovery systems, or systems such as shown on p. 7. Materials: Body: cast iron w/Duragard® coating Extractor: bronze SIZE: 4" x 2" WT.: 15.33 lbs. 233-V-4420 OP W 233- _ The OPW 233 -VM extractor is a multi -outlet extractor, available in 2 sizes; used in direct manifolded systems, vapor recovery, or where provision for Stage II Vapor Recovery is needed. SIZES: 4" x 2" x 3" WT. 18.73 lbs. 233 -VM -6045 4" x 2" x 2" WT. 16.62 lbs. 233 -VM -4422 - All OPW 233-V series extractors are specially coated with black Duragard coating, for improved corrosion resistance and easier cage removal. OPW 233 Series Extractor fittings allow foot valves and ball float vent valves to be removed from under- ground tanks without breaking up the concrete. See pg. 12 for OPW extractor wrench selection. OP 23 -E 11/2" Size Top threw 4" Outlet thread 11/2" Inletmalethread 4" Inlet female thread 11/2" Maximum clear I.D. 2" through valve 27/8" OP 233-P 2" Size Top thread 4" Outletthread 2" Inlet thread 4" Cagethread 2" Maximum clear I. D. 2" through valve 131/2" 233 -VP Test Plugs OPW Test Plugs are used to isolate the tank from the vent piping system during tank testing. The 233 -VP plug is used on: 233-V-4420 (4" x 2") 233 -VM -4422 (4" x 2" x 2") The 233-VMP plug is used on: 233-V-4420 (4" x 2") 233 -VM -4422 (4" x 2" x 2") 233 -VM -6045 (4"x 2" x 3") 233 -VM -5522 (4" x 2" x 2") 233 -VP -6046 WT.: .78 lbs. 233-VMP-6047 WT.:1.24lbs. 233V 233VM 233VM 233VM 4420 4422 6045 5522 (Tee) (Cross) (Cross) (Cross) Top Thread 4" 4" 4" 4" Outlet Thread 2" 2" 2" 2" — 2" 3" 2" Tank Connec- tion Thread Ext. Ext. 4" 4" I Ext. 4" Int. 4"