Laserfiche WebLink
"--'UL/ULC LISTED SECONDARY CONTAINMENT FITTINGS <br />SIZES AVAILABLE <br />BOW 8169 outlet <br />Threaded skis oxlet <br />NPT Internal Threada(2) <br />3" x 2" <br />3" x 1" <br />4"x2" <br />3"x11/4" <br />4" x 3" <br />3" x 1'/z" <br />Modulus of Elasticity in Tension at 750 F 1.92x 106 psi <br />at 1500 F 1.7Q,x 106 psi <br />4"X1" <br />ASTM D-2105 <br />4" x 1'A" <br />4"X1%" <br />*NOTE: 6" secondary containment fittings are not UL/ULC Usted. <br />PRESSURE RATINGS <br />SADDLES <br />t ,t <br />Bending Properties of RED THREAD II Pipe <br />Tensile Strength — Axial at 750 F 11;900 psi <br />i f <br />t <br />' <br />at 1500 F 9;300 psi <br />64.12 MPa <br />Compressive Strength — Axial at 750 F 22,700 psi <br />156.51 MPa <br />ASTM D-695 <br />Modulus of Elasticity in Tension at 750 F 1.92x 106 psi <br />at 1500 F 1.7Q,x 106 psi <br />1.32 x 104 MPa <br />1.17 x 104 MPa <br />ASTM D-2105 <br />Ultimate Hoop Tensile Strength at Burst <br />Average at 750 F 44;000 psi <br />303.37 MPa <br />ASTM D-1599 <br />Long Term Hoop Strength at 750 F 9,140 psi <br />Cyclic Pressure (150 x 106 cycles) <br />63.02 MPa <br />ASTM D-2992 <br />*NOTE: 6" secondary containment fittings are not UL/ULC Usted. <br />PRESSURE RATINGS <br />SADDLES <br />t ,t <br />Bending Properties of RED THREAD II Pipe <br />Tensile Strength — Axial at 750 F 11;900 psi <br />82.05 MPa <br />ASTM D-2105 <br />at 1500 F 9;300 psi <br />64.12 MPa <br />Compressive Strength — Axial at 750 F 22,700 psi <br />156.51 MPa <br />ASTM D-695 <br />Modulus of Elasticity in Tension at 750 F 1.92x 106 psi <br />at 1500 F 1.7Q,x 106 psi <br />1.32 x 104 MPa <br />1.17 x 104 MPa <br />ASTM D-2105 <br />Ultimate Hoop Tensile Strength at Burst <br />Average at 750 F 44;000 psi <br />303.37 MPa <br />ASTM D-1599 <br />Long Term Hoop Strength at 750 F 9,140 psi <br />Cyclic Pressure (150 x 106 cycles) <br />63.02 MPa <br />ASTM D-2992 <br />at 1500 F 8,020 psi <br />55.30 MPa <br />Procedure A <br />Thermal Expansion Axial <br />2" 3" 4" pipe 1.09 x 10-5 in./in./OF <br />1.96 x 10-1 mm/mm/0C <br />AOSI-TM16-3 <br />Thermal Conductivity <br />2" 3" 4" pipe 2.9 BTU/(ft2)(hr.)(OF/in.) <br />0.42 W/(m)(0K) <br />AOSI-TM16-15 <br />Specific Gravity 11.85 <br />1.85 <br />ASTM D-792 <br />Flow Factor <br />Hazen -Williams Coefficient 1150 1 150 1 AOSI <br />(1) A 3"x 2" reducer bushing which is (2) Threaded connections (3) Sharper bends should be eliminated (4) Data not available at time of (6) Pipe is manufactured in compliance <br />not UL/ULC Listed is available for must be made with a to avoid stress conelentration which printing. with ASTM D-2996. Refer to general <br />use with the 4"x 3" termination flexible connector. would result in premature pipe failure specification sheet in catalog for the <br />concentric reducer. under pressure conditions. (6) Tests run on pipe samples. D-2996 designation code. <br />