COMPLIANCE INFO_1995-1999 - Laserfiche WebLink

Home Browse Search

® VEEDER-ROOT PRESSURIZED LINE LEAK DETECTION SITE PREPARATION AND ® INSTALLATION INSTRUCTIONS C. LINE LEAK SENSOR FIELD WIRING D. PUMP CONTROL W1RING CONNECTIONS. See Figure 8, "Pressurized Line Leak Detection System 1. Turn OFF all AC power to the TLS system and sub- and Pump Control Diagram for Red Jacket Relay Control mersible pump. Box" and Figure 9, "Pressurized Line Leak Detection System and Pump Control Diagram for Non-Red Jacket 2. Using wire nuts, connect the wires from the Line Relay Control Box" Leak Sensor to field wires in the junction box. Be sure to maintain correct circuit orientation The TLS monitor must be able to detect when dispensers between the color-coded or marked field wires are ON or OFF so it only initiates line leak tests when the and PLLD sensor wires during wiring. dispenser is OFF. The monitor must also be able to start 3. Seal wire nut connections using the epoxy sealant the submersible pump to perform a line leak test, and furnished with each PLLD. Use one packet for no shut the pump off if a leak is detected. more than two wire nut connections (see Figure 7, This is accomplished by interrupting AC Line between "Epoxy Sealant Connections"). the "Dispenser ON Switch" and the pump contactor. Typically, you can break the AC Line from the "Dis- .211 penser ON Switch" in the submersible pump relay con- WARNING: EPDXY SEALANT MAY BE IRRI- trol box. TATING TO EYES AND SKIN AND MAY CAUSE SKIN SENSITIZATION IN SUSCEPTI- The "Dispenser ON" signal may come from a Point-of- BLE INDIVIDUALS. EPDXY SEALANT MAY BE Sale terminal, self-serve console or switch inside the dis- ABSORBED THROUGH THE SKIN. EPDXY penser, from which the AC Line will enter the pump SEALANT CONTAINS EPDXY RESIN AND VI- relaycontrol box. NYL CYCLOHEXENE DIOXIDE WHICH HAS BEEN SHOWN TO CAUSE CANCER IN LABO- CAUTION: LINE LEAK DETECTOR WIRING RATORY ANIMAL TESTS. FOR RED JACKET SUBMERSIBLE PUMPS IS PRECAUTIONS: AVOID EYE AND CONTACT DIFFERENT THAN WIRING FOR OTHER WITH SKIN. WEAR IMPERVIOUS GLOVES PUMPS. SEE Figure 8, "Pressurized Line Leak AND SAFETY GLASSES AND USE ONLY IN Detection System and Pump Control Diagram for WELL VENTILATED AREAS. Red Jacket Relay Control Box", AND Figure 9, "Pressurized Line Leak Detection System and Pump Control Diagram for Non-Red Jacket Re- TO SENSOR TO MONITOR lay Control Box" FOR THE APPROPRIATE WIR- ING DIAGRAM. 1. Turn off all AC power to the TLS monitor, dispens- ers and submersible pumps. TIE WRAP 2. Connect the AC Line from the "Dispenser ON Switch'to the wire leading to the PI (PUMP IN)ter- / minal on the Line Leak Interface Module. '~-"-PACKET 3. Connect the wire from the PO (PUMP OUT)termi- EPDXY SEALANT nal on the module to the AC Line side of the pump 1 contactor. WIRE NUTS 4. Connect the PR (PUMP RETURN) wire from the Figure 7. Epoxy Sealant Connections module to AC Neutral as shown in Figure 8, "Pres- surized Line Leak Detection System and Pump Con- CAUTION: IF MORE THAN TWO WIRE NUT trol Diagram for Red Jacket Relay Control Box" or CONNECTIONS SHARE AN EPDXY SEALANT Figure 9, "Pressurized Line Leak Detection System BAG, THE CONNECTIONS WILL NOT BE and Pump Control Diagram for Non-Red Jacket PROPERLY SEALED. IMPROPER SEALING Relay Control Box". OF THE CONNECTIONS WILL RESULT IN IN- ACCURATE SYSTEM READINGS AND POSSI- 5. Connect the AC Line from the main power panel to BLY FALSE ALARMS. the L1 terminal on the module. 12