Laserfiche WebLink
40 <br />Approximate No. of Bonds per Kit <br />Working <br />L1 <br />21' 3" 411 <br />3" <br />(50 mm) (75 mm) (100 mm) <br />(Min.) <br />25 18 10 <br />25 <br />18 10 6 <br />25 <br />_ <br />25 <br />2 Solvent does not come with the adhesive kits; (3) Not recommended for 2", 3", and 4" (50 mm, <br />(1) Working life is the time it takes a properly O 75 mm, and 100 mm) installations because of the <br />mixed can of adhesive to "set up" at 75T. it must be ordered separately. • <br />large quantity of adhesive per kit. <br />Number of bonds is based on the volume in the <br />kit and must be completed within the working <br />life of the kit. <br />• Wire bushes may be used for cleaning T.A.B. surfaces; <br />however, they must be clean and free of oily contami- <br />nation. <br />• Dirt contamination can be removed by water washing. <br />Be sure the surfaces are dry before bonding. <br />Note: Using solvent as a cleaning method is <br />optional. <br />If preferred by the customer, use solvent. <br />Trichloroethylene solvent is available from Smith <br />Fiberglass Products. Some alternate cleaning solvents <br />available through local hardware or industrial supply <br />houses are acetone, alcohol, methylene chloride, and <br />methyl ethyl ketone. After cleaning, be sure any resid- <br />ual solvent has evaporated before applying adhesive. <br />DO NOT USE SOLVENTS THAT LEAVE AN OILY <br />FILM ON THE BONDING SURFACES. <br />WARNING: <br />Some <br />degreasers and <br />solvents are <br />extremely <br />flammable. Be <br />sure to read <br />warning labels <br />on containers. <br />Never use <br />gasoline, <br />turpentine, or <br />diesel fuel to <br />clean joints. <br />FIGURE 1.6.5 <br />Installation Instructions <br />10 <br />Approximate No. of Bonds per Kit <br />Working <br />2„ <br />311 <br />411 <br />Life(1) <br />Kit(z) <br />Quantity Mixed Adhesive <br />(50 mm) <br />(75 mm ) <br />(100 mm) <br />(Min.) <br />DS -8014 <br />6.4 oz. (181 g) <br />21 <br />15 <br />8 <br />7 <br />15 <br />15 <br />DS -8024 (twin pack) <br />2.7 oz. ea. (77 g ea.) <br />18 <br />12 <br />2 <br />15 <br />DS -8055 (bag kit) <br />1.6 oz. (45 g) <br />6 <br />4 <br />_ <br />15 <br />DS -8069(3) <br />9.3 oz. (264 g) <br />- <br />2 Solvent does not come with the adhesive kits; (3) Not recommended for 2", 3", and 4" (50 mm, <br />(1) Working life is the time it takes a properly O 75 mm, and 100 mm) installations because of the <br />mixed can of adhesive to "set up" at 75T. it must be ordered separately. • <br />large quantity of adhesive per kit. <br />Number of bonds is based on the volume in the <br />kit and must be completed within the working <br />life of the kit. <br />• Wire bushes may be used for cleaning T.A.B. surfaces; <br />however, they must be clean and free of oily contami- <br />nation. <br />• Dirt contamination can be removed by water washing. <br />Be sure the surfaces are dry before bonding. <br />Note: Using solvent as a cleaning method is <br />optional. <br />If preferred by the customer, use solvent. <br />Trichloroethylene solvent is available from Smith <br />Fiberglass Products. Some alternate cleaning solvents <br />available through local hardware or industrial supply <br />houses are acetone, alcohol, methylene chloride, and <br />methyl ethyl ketone. After cleaning, be sure any resid- <br />ual solvent has evaporated before applying adhesive. <br />DO NOT USE SOLVENTS THAT LEAVE AN OILY <br />FILM ON THE BONDING SURFACES. <br />WARNING: <br />Some <br />degreasers and <br />solvents are <br />extremely <br />flammable. Be <br />sure to read <br />warning labels <br />on containers. <br />Never use <br />gasoline, <br />turpentine, or <br />diesel fuel to <br />clean joints. <br />FIGURE 1.6.5 <br />Installation Instructions <br />10 <br />