Laserfiche WebLink
40 1111111111111110 <br />A D ER cOMPANY <br />WRW11 <br />Instructions <br />Emergency10 Series* Shut -Off <br />IMPORTANT: Please read all warnings and follow <br />the installation instructions completely and <br />carefully. Failure to do so will void all warranties <br />and may cause product failure, or result in <br />environmental contamination due to liquid <br />leakage into the soil, creating hazardous spill <br />conditions. <br />WARNING - DANGER: Using electrically- operated <br />equipment near gasoline or gasoline vapors may <br />result in fire or explosion, causing personal injury <br />and property damage. Be sure that the working <br />area is free from such hazards, and always use <br />proper precautions. <br />WARNING: Proper operation is dependent on <br />,proper installation and regular maintenance. The <br />following instructions are provided to assist you <br />in properly installing and maintaining your 10 <br />Series Valve. Failure to follow these instructions <br />may cause failure of the valve to close in the <br />event of an emergency, resulting in a.hazard®us <br />condition. <br />The valve body must be! <br />e idly ar►ehored to a: <br />structural member with- the island to insure <br />breakage at the shear o in the event of <br />severe impact. Failure to provide a rigid <br />mounting may result in a failure of the valve to <br />close or break in a portion of the inlet pipe In the <br />event of severe impact, resulting in an excessive <br />loss of product and a hazardous condition. <br />The shear groove must be at the same level or a <br />maximum of 1/2" above or below the top of the <br />pedestal island. Failure to install the shear <br />groove at this levet may cause a failure to break- <br />off in the event of severe Imp t,;resulting in a <br />hazardous condition. <br />CAUTION: The hub sub -assembly must have <br />ample clearance to prevent striking against the <br />side of the pit as the valve closes. If the lever hits <br />the side of the pit, the valve will not close in the <br />event of an emergency resulting in a hazardous <br />condition. <br />IMPORTANT NOTICE: When mounting the OPW 10 <br />Series Emergency Shut -Off Valves, the anchoring <br />device employed must withstand a force greater <br />than 650 ft. pounds per valve. Stabilizer mounting <br />bolts are provided with each valve. U -Bolt <br />mounting hardware (10UBK-015) must be <br />IMPORTANT: <br />WHEN USING THE U -BOLT MOUNTING METHOD, <br />ONLY USE AN OFFICIAL OPW U -BOLT, ANY <br />OTHER U -BOLT USED VOIDS ANY AND ALL <br />PRODUCT WARRANTIES. <br />U -BOLT CONNECTION STABILIZER CONNECTION <br />Figure 1 <br />HOW TO ATTACH VALVE TO RISER STUB <br />FCoat riser stub with a UL classified gasoline - <br />resistant pipe -joint compound (non -hardening) before <br />attaching the valve to the riser stub. <br />DO NOT USE TEFLON TAPE <br />Thread valve tightly onto`riser 6tub by grasping <br />inlet end surface "A". (See Figure 2.) <br />If you don't have room in the pit to attach wrench' <br />on surface "A", use OPW Wrench 10 -RW. <br />A dirt protector is supplied in the outlet,en'd of the <br />valve and should remain in pla6,e`,tun6l<1 ° 1 Anal <br />connection is made between the valve and ped, I# <br />CAUTION: Tighten threads until tight seal is, <br />obtained. Additional tightening may cadseAe <br />body to crack and allow product leakage -at test or� <br />in service. (TORQUE SPECIFICATIONS 125-135 <br />FOOT POUNDS) <br />* Listed by Underwriters Laboratories <br />OPW 10 Series Emergency Shut -Off Valves Page 1 <br />OTE: MSPENBER 70 eE <br />Shear <br />TTAeNeD To O AND PER <br />1 <br />Groove <br />nlet <br />'r:at>` OPW <br />' Inlet <br />I Pipe <br />Stabilizer Pipe <br />Angle Iron rigidly supported <br />Bar <br />Angle is embedded In concrete. <br />whin the manhole and <br />the <br />Short angle bolted to valve to <br />valve mounted to It by means <br />make certain valve and Inlet <br />of a u -bolt <br />piping are rigid. <br />Figure 1 <br />HOW TO ATTACH VALVE TO RISER STUB <br />FCoat riser stub with a UL classified gasoline - <br />resistant pipe -joint compound (non -hardening) before <br />attaching the valve to the riser stub. <br />DO NOT USE TEFLON TAPE <br />Thread valve tightly onto`riser 6tub by grasping <br />inlet end surface "A". (See Figure 2.) <br />If you don't have room in the pit to attach wrench' <br />on surface "A", use OPW Wrench 10 -RW. <br />A dirt protector is supplied in the outlet,en'd of the <br />valve and should remain in pla6,e`,tun6l<1 ° 1 Anal <br />connection is made between the valve and ped, I# <br />CAUTION: Tighten threads until tight seal is, <br />obtained. Additional tightening may cadseAe <br />body to crack and allow product leakage -at test or� <br />in service. (TORQUE SPECIFICATIONS 125-135 <br />FOOT POUNDS) <br />* Listed by Underwriters Laboratories <br />OPW 10 Series Emergency Shut -Off Valves Page 1 <br />