COMPLIANCE INFO_2011-2018 - Laserfiche WebLink

Home Browse Search

a around the Snap Tap threads. j. , Replace the caps over the. quick -connect couplings and tighten snugly. DO NOT overtighten. ® See technical bulletin #042-111-1 for use of Snap Tap Connector Assembly. 7. Connect power to pump at the load center. " 8. Clear remaining air from system as follows: a. Turn on dispenser that is farthest from the leak detector -b t do not open nozzle: Wair4 of 5 minutes ormore. Look for leaks on parts worked on. b. Shut off the pump and allow it to stand four or five minutes. Then startthe pump again nozzle farthest from the leak detector. c. Continue to dispense enough gasoline, ab gallons (76 to 114 liters), to pump ALL system. Y E + For FX2V modelsP a. Remove 1/4 -inch pipe plug from tank test port in the ®. If flow is restricted to about 3 gpm (ll 1pm) or fess Packer (on 6 -inch Big -Flo applications, remove the with the nozzle open, the leak detector has not 1/4 -inch pipe plug from the riser/flanje assembly). opened. Repeat step 8a with increased running b. Apply a UL -classified non-toxic pipe thread sealant to time of pump to insure the purging of all air. All air the 1/4 -inch NPT 45 -degree elbow and install in tank' must be purged from the system or the leak detector will restrict flow to about 3 gpm (11 Ipm). test port of the packer. On 6 -inch Big -Flo applications, the 1/4 -inch NPT 45 -degree elbow may be •installed `9. Affix the enclosed decals to the dispenser dial glass on grade into the riser/flange assembly. of gasoline upon which the leak detector is being installed. c ---- e thread sealant lpandlpinstall tomerst at decals are bassureltheervic a - 18001262- - the 1/4 mch1NPT�hex nippteassified — on 45 degree 539 usare elbow that. is in the tank test port (or on 6 inch Big -Flo ti ande 10. Inspect all .threaded ,loints toy gh not riser/flange assembly leaking. d. Apply a UL -classified non-toxic pipe thread sealant to, the 1/4 -inch NET tee and install on the hex nipple to est Of the Leak Detector accommodate both the vent tube and the snap tap: U.S. Environmental Protection ,Agency (EPA) regulations require e. Apply a UL -classified non-toxic pipe thread sealant to annual verification of _operation of leak detector. To assure the threads of the 1/4 -inch NPT 90 -degree elbow vent of the 1/4-inch maintenance of leak detection capability, Red Jacket requires that. tube fitting. operanonof�t-lie-mechaaziical leak -detector be verified by testm`g upon f. Apply a UL -classified non-toxic pipe thread sealant to start-up and that testing of the leak detector be performed routinely at the threads of the 1/4 -inch NPT straight vent tube least annually. fitting and install in the leak detector vent opening in the cap of the leak detector. F r ®' ?'t Test procedure options for mechanical leak g: Install the vent.tubing mto:bothfittings,and tighten per detectors are explained in Red Jacket Engineering instructions on package. Reports, RJ20 and Rd21. The Red Jacket:Snap Tap h. To install snap. dap connectors in FX2V/FX21)V Connectors allow the FX2V/FX2DV leak.,detector models, apply a UL -classified non-toxic, thread to be tested with the EXV Snap Tapdiester as An sealant to the snap tap connectors and install one in the option to the above test methods. See: Red Jacket body of the FXV leak.detector and. the other. in the tee literature .#042-111-1 for test instructions using attached to the hex nipple' attached to the 45 -degree Snap Tap Connectors. elbow installed in the tank test.port of the packer. On 6- 11. The top cover on the Red Jacket Leak detector is designed to inch Big -Flo applications, install the two snap tap accommodate .a sealing wire which can be used, to connectors - one in the body of the FXV leak detector discourage tampering or the unauthorized removal of leak and one in the riser/flange assembly. detector. (See Figure 2). i. Attach and crimp loop of the retaining tether a around the Snap Tap threads. j. , Replace the caps over the. quick -connect couplings and tighten snugly. DO NOT overtighten. ® See technical bulletin #042-111-1 for use of Snap Tap Connector Assembly. 7. Connect power to pump at the load center. " 8. Clear remaining air from system as follows: a. Turn on dispenser that is farthest from the leak detector -b t do not open nozzle: Wair4 of 5 minutes ormore. Look for leaks on parts worked on. b. Shut off the pump and allow it to stand four or five minutes. Then startthe pump again nozzle farthest from the leak detector. c. Continue to dispense enough gasoline, ab gallons (76 to 114 liters), to pump ALL system. Y It should be noted that if the dispensing system (the Nazi : EM solenoid valve and the nozzle) is opened previous to the completion of the line test,. the FXV Series will detect this opening as a,leak and restricted flow will result. Closing of the nozzle(s) for a period of time adequate to allow completion of the line test will allow the leak detector to open. Once opened, full pump floNy can be provided. r and open the FX2V / FX2DV out 20 to 30 air from thep SNAP TAP 'Figure 2 O SEALING WIRE t (provided by contractor) + o t Y ]Figure 2 TETHERED CAP 45° ELBOW tl l ,1 /4 -INCH T -FITTING F NT TUBE f tl, dq a}. E It should be noted that if the dispensing system (the Nazi : EM solenoid valve and the nozzle) is opened previous to the completion of the line test,. the FXV Series will detect this opening as a,leak and restricted flow will result. Closing of the nozzle(s) for a period of time adequate to allow completion of the line test will allow the leak detector to open. Once opened, full pump floNy can be provided. r and open the FX2V / FX2DV out 20 to 30 air from thep SNAP TAP 'Figure 2 O SEALING WIRE t (provided by contractor) + o t Y ]Figure 2 TETHERED CAP 45° ELBOW tl l ,1 /4 -INCH T -FITTING F NT TUBE f tl, dq a}.