COMPLIANCE INFO_2003 - Laserfiche WebLink

Home Browse Search

Jun . 5 . 2003 9 :22AM Gla 6 Environmental No ,0651 P. 3 HOLODOWN STRAPS: , Xerxes FRP straps must be used when a tank is to be anchored. The location of holddown straps for each tank is marked on the WARNING,Do not use air pressure to test tanks that contain tank by the arrow(><)symbol.Complete data for holddown flammable or combustible liquids or vapors.The fuel/air mixture straps are given in Figure 7-2 and Table 7-2, may explode and muse death,severe personal Injury or property CAUTION:Place the sups only In the locations designated by the damage.Tanks that will be ballasted with a flammable product arrow symbol(><), should be air tested before ballasting. To evenly distribute buoyancy loads,tighten all holddown straps WARNING:If product Is used as ballast,exercise special care In uniformly until they are snug over the ribs but cause no deflection handling.Safeguard against sparks,fire or product spills.improper of the tank.Make an Intermediate measurement of the tank dWT& handling of product can cause a fire or explosion,and may result ter AFTER the stray have been Installed and tightened. In death,severe personal injury or properly damage. HARDWARE AND ANWRIN01 POINTS: INTERMEDIATE DEFLECTION MEASUREMENT Armoring hardware and anchor pointe must be shed according After backfill Is brought to the top of the tank,make an intermediate to Table 7,3.The installing contractor Is responsible for providing measurernemt of kcal deftection wording to the instnctions hardware and anchor points of sufficient strength,The particular In Section 13, configuration of hardware will be determined by the owner or the TEST owners representative. the anchor points as shown In After the tank has been measured and vmtcal detiedion Is deter- Table 7-2.Infer to dirnansion"E".Align all anchor points with the mind to be within the limits specified by Ymm.ft tank must be marked(><)loogm on the tanks,within atolerarce of t 1".For tasted to ensure that no damage occurred during installation.The specific Information on hardware,cable,able clamps and their procedure in Section 2 Pre-Installation Testing should be fold, use,consult the manufacturers of these iters. soaping all exposed areas of the tank and all fittings. Because most of the tank exterior is no longer visible,the tank TABLE 7.3 must be lested by acting the gauge at the test manifold for any TANK s,Mo& 4,01111• elm- drop In pyre,Carefully relieve tine pressure in the tank and rtlr Below elm GREATER remove the hosaftive assembly from dry Double Wall tanks. WIRE ROPE DIA 3r 1/23 1Z (6 x 19 IPS) TURNBUCKLE DIAWARNING: not use 91r pressure to test tanks that contain JMNYE HOOK12' 50 p 3/4° e or combustible liquids or ors. aIr mixture may explode and cause death,severe personal Injury,or property OR RATING ) 9, 21, 25, .Tanks that will be ballasted with a flammable product should be air Itested before biillastlng, WARNING:If product Is used as Mast,exerclas specW cars In handling.Safeguard against sparks,fire or product spills.Improper handling of product can cause a fire or explosion,and may rift In death,severe personal injury or property The tank may be ballasted after the backfill is even with the top of the tank and pW4nstallstlon testing has been successfully completed.Only under wehole conditions as described In Section 6,should ballast be added before the backfill Is evert with the top of the tank,When filling the tank,male sura the tank Is properly vented.The sent must be large enough to allow the displaced air to escape, o a, g ii4�q I• T111 9-4111111-9411111 ME#III IM11 11119 11OTE:Al at the holdit nr sups,turnbuckles and/or thr rod must be=W or Owtmd to prdvemt conft, M.When fastening Wre cable,km a*imam of three demes an each tont Use shadb4pe or ddmM dwa as appmrhde.