COMPLIANCE INFO_2003 - Laserfiche WebLink

Home Browse Search

UL/ULC Listed RED T EAD° IIA Piping GENERAL SPECIFICATIONS Primary Piping Secondary Containment Piping SCOPE SCOPE PiPE-Pipe shall be manufactured by Smith Fibercast by PIPE- Pipe shall be manufactured by Smith Fibercast by a filament winding process using a thermosetting epoxy a filament winding process using a thermosetting epoxy resin to impregnate strands of continuous glass filaments resin to impregnate strands of continuous glass filaments which are wound around a mandrel at a prescribed helix which are wound around a mandrel at a prescribed helix angle and under controlled tension. .all pipe will be I angle and under controlled tension. supplied with matching tapered T.A.B." (Threaded and Bonded) coupling and spigot ends or T.A.B. spigot x CONSTRUCTION spigot ends. 3"-4"PIPE - RED THREAD IIA pipe shall have continuous CONSTRUCTION glass fibers filament wound at a 35 helix angle in a matrix of epoxy resin. Pipe shall be in compliance with 2"-4"PIPE- RED THREAD IIA pipe shall have continuous ASTN4 D2310 and classified by its designation code. Pipe glass fibers filament wound at a 351/',' helix angle in a shall meet all performance requirements and mechanical matrix of epoxy resin. Pipe shall be in compliance with properties, and shall be classified with the following ASTM D2310 and classified by its designation code. Pipe designation codes: shall meet all dimensional and performance Size Designation Code at 73.4'F requirements. mechanical properties, and shall be ; RTRP-11AE classified with the following designation codes: 4•• RTRP-11AF Size Designation Code at 73.4° F 2"-3" RTRP-11 AE ITEMS q RTRP•11AF 3"-4"PIPE - Glass fiber reinforced filament wound pipe with Plain end by Plain end. Pipe to be factory ITEMS prooftested at the following pressures: 2"-4"PIPE -Glass fiber reinforced filament wound pipe 3" -300 psig(minimum) with matching tapered T.A.B. (Threaded and Bonded) 4". 265 psis(minimum) coupling and spigot ends. Pipe to be factory prooftested at the following pressures: I 3"-4"FITTINGS -Compression molded two-piece fittings 2 -375 psis shall be manufactured using a vinyl ester molding u compound. The molding compond shall be reinforced 3"-300 psig j with a minimum of 60%chopped glass fiber. #--265 psig ADHESIVES -Adhesive and curing agents shall be either 2"-4"FITTINGS-Compression molded fittings shall be manufactured using an epoxy molding compound. The UL Listed DS-8000 or DS-7000 series adhesive. Consult molding compound shall be reinforced with a minimum Smith Fibercast's installation manual No. 62160 for of 459%chopped glass fiber. In-line fittings are filament recommended heat curing techniques. wound. I JOINING TECHNIQUES ADHESIVES- Adhesive and curing agents shall be either I 3"-4"PIPE and FITTINGS- Pipe shall be joined with UL Listed DS-8000 or DS-7000 series adhesive. either DS-8000 or DS-7000 series adhesive. Fittings shall Consult Smith Fibercast's installation manual No. B2160 be joined with either DS-7000 or DS-8000 series for recommended heat curing techniques. adhesives and filler. Material to be installed in accordance with Smith Fibercast's installation manual JOINING TECHNIQUES No. B2160. 2"-4"PIPE and FITTINGS-Pipe and fittings shall be TESTING joined with DS-8000 or DS-7000 series adhesive using matching tapered bell/coupling and spigot. Material to 3"-4"SECONDARY CONTAINMENT PIPE SYSTEMS- be installed in accordance with Smith Fibercast's Secondary containment pipe systems should be tested installation manual No. 82160. prior to use to assure soundness of all joints and connections. Consult Smith Fibercast's installation TESTING manual No. 82160. 2"-4"PRIMARY PIPE SYSTEMS-Primary pipe systems should be tested prior to use to assure soundness of all joints and connections. Consult Smith Fibercast's installation manual No. B2160.