Laserfiche WebLink
Iii <br />_ ® <br />0(209) 836-2310 FAX: (209) 836-2336 <br />23535 S. Bird Road, Tracy, CA 95376 <br />&€P.O. Box 1183, Tracy, CA 95378-1183 <br />€)i (A <br />PREVENTATIVE�j���"' RACE <br />SCHEDULE <br />95 JAN 1 <br />t �t <br />Hospital k—elt.1 ` Contact <br />Address ` Title <br />Date 1,2-16-q4- P.O.# <br />1. Run and check operation of unit: ............. <br />A. All controls function properly ........... <br />B. Manually operate all safety interlocks.. <br />C. Adjust all limit switches ................... <br />D. Compactor cycle works properly........ <br />E. Sterilizer cycle works properly .......... <br />1) Sterilization time: ........ <br />2. Inspect all electrical fuses, <br />connections and indicators ..................... <br />3. Service hydraulic oil filter and strainer...... <br />4. Check oil level with cylinder retracted, <br />fill to level ......................................... <br />5. Inspect all hydraulic components for leaks/ <br />tighten or replace as required: <br />A. Hoses ......................................... <br />B. Fittings ....................................... <br />C. Pump ......................................... <br />D. Valves ......................................... <br />E. Cylinder ...................................... <br />6. Clean any refuse from around power unit .. <br />7. Check hydraulic pressures: <br />A. Full light pressure (1800!1) ............... <br />B. Override relief by-pass (2000#) ......... <br />C. Sterilizer discharge door Crimp (9001) <br />D. Door crimp actuator pressure (1650!) <br />8. Inspect both scraper and wiper blades, <br />adjust/replace..................................... <br />9. Inspect access panels and locks ............... <br />10. Lubricate all wear points: <br />A. Sterilizer locking hub and bars .......... <br />B. Sterilizer load door and hinge............ <br />OK I Service I ATTN <br />3A <br />MA <br />M <br />TEST CYCLE: Parts: <br />Preheat temp (200'F 21V <br />Vacuum: ! It rr <br />Time to temp: <br />Chamber press: _Z <br />Temperature: 2= 60 Remarks: (A vC y o cl a5u-t <br />Vent time: 141% <br />Discharge: 1'i4 <br />Jacket press: A- L io <br />One # <br />Unit #17-04- o5 l 1156 <br />C. Sterilizer ball screw ........................ <br />D. Sliding door rollers and latch ............ <br />E. Compactor lower rollers and tracks..... <br />F. Limit switch rollers ........................ <br />G. Optional equipment ........................ <br />H. Sterilizer safety load door lock .......... <br />11. Blow-out steam and water strainers .......... <br />12. Service and clean bucket traps ................ <br />13. Inspect & clean sterilizer load door seal:.... <br />A. Replace seal as required .................. <br />14. Inspect & clean sterilizer discharge door seal: <br />A. Replace seal as required .................. <br />15. Clean sterilizer chamber ........................ <br />16. Inspect jacket steam hoses ..................... <br />17. Run sterilizer cycle (Test Cycle) .............. <br />18. Inspect liner screw hose & packing .......... <br />19. Check temperature recorder/printer.......... <br />20. Operate discharge override .................... <br />21. Inspect roll -off container: <br />A. Ratchet jacks and hooks ................... <br />B. Door gasket ................................. <br />22. Inspect all anchor bolts and fasteners ........ <br />23. Clean & check liner screw <br />(Mark VII & X only) ............................ <br />24. Check all safety decals .......................... <br />25. Clean exterior of equipment ................... <br />26. Clean underneath equipment .................. <br />27. Notify customer of any suggested repairs <br />that are not covered by PM Agreement <br />Purchase Order required ....................... <br />28. Question any usage problems ................. <br />Factory Engineer , Customer <br />White: Factory Yellow: Customer Revised 3/93 <br />