INSTALL_2018 - Laserfiche WebLink

Home Browse Search

ITEM #38 Intelligent Submersible Turbine Pump Specifications Liquid Compatibility • . • . - • Max.liquid viscosity: 70 SSU at • 60•F (15•C). •IST models imply alcohol-gasoline Atypical turbine model designation compatibility for fuel mixtures containing has up to five components to define diesel fuel with up to 20%biodiesel,100% the pump heing supplied as follows: biodiesel,up to 85%ethanol with gasoline, IST XXXXX Y - A - B `� f I and 20%MTBE,20%ETBE or 17%TAME a with gasoline. IST= Basic Model Designation •IST models can also be used with diesel Note: All IST models include fuels,fuel oils,kerosene,Avgas and jet fuels alcohol-gasoline compatibility, in a non-gelled pourable state. variable speed and variable - t • All wetted elastomers are made of a high length as part of the base model. grade,fluorocarbon compound. XXXXX=Factory Installed Options Standard Features IST model designations may include r • All IST models include variable one or more of the following speed,variable length options and characters in alphabetical order: alcohol-gasoline compatibility. • Check valve:23/4"diameter fluorocarbon F = Floating suction adapter(1112" N PT seal constructed on cast aluminum body female adapter) and steel backing washer. K = Intake filter screen (IFS,factory `•, •Pressure relief valve:available in four installed to PMA) ti pressure relief settings,integral to check M = MagShell' (flow enhancing, valve.Standard model relieves at 40 psi and expanded PMA shell) For full diagram see Ordering Guide. P R' = Model R check valve (24 psi resets above 35 psi. P relief/22 psi reset for PLL D) Power Requirements •Syphon:venturi-type syphon primer W- = Model W check valve (16 psi supplied with every submersible. P IST models can only be powered by a Syphon check valve and secondary relief/13 psi reset for PPM4000) MagVFC" controller: syphon sold separately. Note:If not otherwise specified,all IST - •2 hp models can operate with single-or • Air eliminator:every submersible includes models are supplied with r three-phase incoming power supply to tank return path with one-way check valve standard model check valve (40 the MagVFC". to provide active air elimination. psi relief/35 psi reset for ML D, y, •4 hTS-LS300,and TS-LS500).p models require three-phase incoming • Electrical disconnect:electrical yoke ^` power supply to the MagVFC"for for positive contractor disconnect Y= Pump Motor Horsepower proper operation. during service. Rating- Incoming power supply to the MagVFC" VS4 =4 hp variable speed can be 200-250 VAC,50 or 60 Hz. Approvals "Note:If not otherwise specified,2 hp •MagVFC' outputs a three-phase,variable • Consult factory for applicable approvals. variable speed is implied. frequency signal,valid for FE Petro variable speed pumps only. A=Model Length Quality Certification •2 hp max. motor draw:7 Amps. 1 = 2 hp variable length, 59"-87" •4 hp max. motor draw: 15 Amps. •Franklin Fueling Systems is an ISO 9001 Certified Manufacturer. 2 = 2 hp variable length,90"-151" •MagVFC" max.line draw:20 Amps. 3 = 2 hp variable length,122"-213" VL1 = 4 hp variable length,64"-92" Pump Motor VL2= 4 hp variable length,95"-156" •2 hp or 4 hp,variable speed,two-stage C U� US LISTED VL3 = 4 hp variable length,127"-218" centrifugal type pump motor with integral, Note:IST-2 and ISTVS4-VL2 models fit automatic,thermal overload protection. 94%of all known installations. • Max.flow:2 hp = 110 gpm,4 hp= 140 gpm. B=Riser Pipe Length • Max.pressure:selectable operating Riser pipe length is expressed as two pressure on MagVFC" between 24 psi and 42 psi deadhead. numeric characters that indicate the total length of the riser in inches. Riser • Available with MagShell",which results in pipes are available from 7"to 69"in 45%increased flow area around motor. 1"increments(additional charge for risers 31" or longer). 16