COMPLIANCE INFO_2019 - Laserfiche WebLink

Home Browse Search

IMPORTANT: The instructions below for the 7150 Upper Tube Length = g +1Lµ t ? .~. t1PL'ER TUBE t» CA + aNC + (A� Overfill Prevention Valve are written for the initial uNKNow ►.L stage shutoff at 95%, but can be adjusted to shutoff For testable models only, ending In wre at any desired tank capacity. Please contact the Au- Upper Tube Length = C + (A) — 1 - i /2" thority Having Jurisdiction (AHJ) and review local, state, and national codes to determine the regulato- YES Upper tube length Is 6= 1 /2" plus the riser pipe ry requirements governing shut-off capacity in your measurement (A), region, as well as take into account other considera- tions such as extreme tank tilt. In all cases, the up- Upper Tube Length = 6- 1 /20 + (A) per tube must protrude into the tank at least 61 /2" to ensure that the valve can shut ON flow into the For testable models only, ending In " T": tank completely before the top of the tank is wetted Upper Tube Length = 6-1 /2 " + (A) - 1 -1 /2" as per EPA requirements . NOTE : You must find the actual tank capacity num- HOW TO LOCATE THE POSITION OF THE 71 SO AT ber that correlates to the 6-112" + (A) depth for the 95% TANK CAPACITY station records. This number may also be used for (Shut-off paints can be adjusted to any capacity to the purposes of calibrating an electronic tank level comply with AHJ Requirements) system. The length of the upper tube and the placement of the Tape measure 71 SO valve body determine the shut-off point. Follow- ing the standard instructions for the OPW 7150 will pro- vide for initial shutoff at 95%. In all cases, the upper tube length must be a minimum of 6- 1 /2" plus the length of the riser pipe. All length measurements are in inches. r "Mp" uaszFzSb gtat we . �5`s^tn. sxr 11r4SD) INSTRUCTIONS Fqc* TLa S D Dz SSL:L- - %wg Riser Pipe with Face (A) 1 ) Find tank capacity (in gallons) from tank calibration Seal Adaptor To Tante Top (I . D.) (S ) chart provided by tank manufacturer. I €�, 0 � 3 To Tank � 2) Calculate 95% of capacity 41531 . 3 S Bo omw 3) Locate the 95% volume number on the tank calibra- tion chart. $ 5 " ; q, 4) Find the dipstick number (ewhich corresponds to the 95% tankvolume. And, find the dipstick num- Figure ber (Y) which corresponds to the 100% volume. 4N 5) Subtract the dipstick number (X) from the tank di- EXAMPLE ameter (Y) to find the upper tube reference number Wo Q S •• f3S sm 10 1 ) For an Owens-Corning Model G -g FibercPlass• Tank Calibration Chart: (17 - (X) = (Z} Tank Capacity _ 10,000 gal ., nominal 9,403 gal. 6) Subtract 2" from (Z) to find the upper tube depth NOTE: Use actual capacity only (C) . SES NbTg 2) 95% of actual tank ca X � „ :: C capacity = 0.95 x 9403 gal. (Z) / = C It 8933 gal. 7) Is C less than 6- 1 /2 "? !a 3 ) The closest number which is less than 8933 gal . Is 8910 gal. Choosing the closest number less than 95% of actual capacity ensures that the initial NO Upper tube length is C plus the distance from shutoff will occur when the tank is no more than the top of the Face Seal Adaptor installed on 95% full. the riser pipe to the inside, top lip of the storage 4) The calibration chart reading of 8910 gal . corre- tank (A). sponds to a dipstick measurement of 82 ". 4