COMPLIANCE INFO_2019 - Laserfiche WebLink

Home Browse Search

waste. If the leak cannot be corrected the spill contain- Height Adjustment Bolt er or bellows should be replaced. As an alternate to a hydrostatic test a vacuum test can be performed on the spill container. Using OPW DW-VAC- TEST and SC-TEST, perform a vacuum test on the spill con- tainer. An initial vacuum of 15 " of water should be attained and the spill container must retain a vacuum of at least 12 " �-- Shims of water after 5 minutes. (See DW-VAC-TEST Instructions.) Cap --i� Step 9: (See Figures 2 & 5) Before pouring concrete, place plastic over the cover and Mounting Ring protecting them from concrete splash . Adaptor Double check that the unit is level and at proper grade height. Pour concrete per Figure 5 . Ramp or dome the Figure concrete away from the mounting ring . There should be a minimum of 1 " slope to finish grade . Slope 1 " Down From Top of Mounting Ring NOTE: Do nor stand on spill container before concrete sets UPS Finish Grade Remove plastic from cover after concrete has dried . Remove adjustment system . Re-test the spill containers for leaks as :' e �. 4 , • .. described in Step 8, after the concrete has set up. - ' "'' ' 14 1 Operation and IwalntenaDce: v • • . a ,. v • . : a : : . . .- a ,, ♦ 1 . . '' .��d a ♦ . 4q'+� a i idly q I • 4o+a After each fuel delivery, the operator must remove any stand- • IF, Ing fuel from the container. Fuel can be removed by actuat- • Z ' " ' rIF k ` ing the drain valve or with a gasoline absorbing disposable :' •�• ; :°' ° ' ` 4i ' ' ; 4 4 ' \•�' g 9 P tee . . � q . � towel . If access to drop tube or overfill valve is required re- , %\ r e • a o ; ® " move Nipple Adaptor from primary bucket. \ a d v D 10 P Weekly: Perform a visual inspection of the interior of the con- tainment bucket for water or other contaminants. If water or other contaminants are found they must be disposed of with Figure s disposable towels. Dispose of towels safely and per all appli- cable local, state and federal codes. Check that cover is in good condition and properly identified. Replace cover and , r seal as necessary. Inspect the bucket walls for cracks, bulges i1; _ i IF or holes. If any exist, have that spill container barricaded and r Min Clearance ! contact maintenance personnel immediately for repairs. NOTE: The bellows and base on the spill container can be ; replaced if damaged. ° ` - JIi _ a, - i , Semiannually: Follow all state and local required hydrostatic ' _ B or vacuum testing on the buckets. Inspect and clean the inte- t rior of the spill container and drain valve screen . Remove ac- r ' ,q cumulated dirt and grit. Where applicable, test the drain it valve using CARB procedure TP-201 . 1 C or TP-201 . 1 D. If the 171 " drain valve passes testing no further maintenances required . If r Ref the drain valve fails testing, remove the valve, soak in water . and use high-pressure air, if needed, to clean. Reinstall the drain valve to its proper position and where applicable, test F - the valve with CARB procedure TP-201 . 1 C or TP-201 . 1 D. If - - _,,_____„� problems persist, replace the drain valve with P/N 1 DK-2100- EVR (specified torque 11 .5 ft-lbs min to 13 ,5 ft-lbs max, 5/ 16- 18 UN thread) . The sealable cover ( 1 SC) adjustment nut is set at the factory, but due to environmental conditions it may be necessary to adjust it to either improve sealing or ease cover LLength of Nipple = Dimension A - Dimension B - Dimension C • 2" twin removal . Figure 6 IMPORTANT: Leave these instructions with the Station Operator.