WORK PLANS - Laserfiche WebLink

Home Browse Search

OUTDOORLIGHT SENSOR+-+-PWR INAC/DCOUTPUTOTS/OLS WIRING DETAILSCALE: NoneCABLING: 18/2 (Electrical Install)FROM: EM-3 Terminal StripINSTALLATION: When installing make sure enclosure is:·Weather-proofed·Mounted with the white PVC sensor pointeddownward·Not mounted on any removable access door orHVAC Unit.·Positioned to allow the Outdoor Light Sensorexposure to full ambient daylight but is notshadowed or exposed to any artificial illumination.MOUNTING LOCATION: On the north/northeast side ofthe building.FROM: EM-3 Terminal StripINSTALLATION: N/AINDOOR CARBON DIOXIDESENSOR DETAILSCALE: NoneMOUNTING LOCATION: To be determined by customer8910111262BACK VIEWCABLING: 18/4 (Electrical Install)GND R -24 +24 G D W2O/B W1 Y2 Y1POWERDI-2DI-1COM--+COM--+DIG INPUTSAUX SNSRNETWORKONRTU WIRINGTERMINALSRGW2W1Y2Y124C(YELLOW)(BLUE)(WHITE)(ORANGE)(GREEN)(BLACK)(RED)--+REMOTESENSOR--+REMOTESENSORBACK VIEW OF SIMPLESTAT 1INDOORTEMPERATURESENSOROptionalManual temperature adjustment disabled.Temperature adjusted through FacilityPage only.SUBNET #1 SIMPLESTAT COMMUNICATION+-SUBNET #1 SHIELD+-SHIELDSHIELDDUCT SENSORSCALE: NoneNEXTTYP.SSCSUBNET #1 SIMPLESTAT COMMUNICATIONSIMPLESTAT WIRING DETAILSCALE: NoneCABLING: 18/2 (Mechanical Install) - 18/8 (ELECTRICAL INSTALL)FROM: EM-3 Terminal StripINSTALLATION:·Install cable between SimpleStat Thermostat module and RTU·Terminate R, G, Y1, Y2, W1, and W2 for control of fan, cooling, and heating. Secure the communications cables to the SimpleStat asshown.·If using a remote space temperature sensor, it must be connected prior to applying power to the SimpleStat.·Provide 24VAC power to the SimpleStat Thermostat Module from the RTU transformer. Power to the controller must be off whileterminations are made.MOUNTING LOCATION: To be determined by customer161718coolheatfancoolerwarmerreadyFRONT VIEW OF SIMPLESTAT 1465PFR1123465PFR2123ABCF2 - 3AA1B1C1F3 - 3AF4 - 3AABCAɸBɸCɸAɸBɸCɸPHASE LOSS PANEL 01-442465PFR X123AɸBɸCɸ1st CIRCUIT2nd CIRCUITXTH CIRCUITCABLING: 18/2 (ELECTRICAL INSTALL)FROM: ESC I/O Terminals 28, 29INSTALLATION:·Line voltage per NEC·PFR shown in an alarm condition.MOUNTING LOCATION: Adjacent to monitored panels.PHASE LOSS MONITOR(S)WIRING DETAILSCALE: NoneOUTDOORTEMPERATURE SENSORILS (MK7-B) WIRING DETAILSCALE: NoneCABLING: 18/2 (Electrical Install)FROM: Auxiliary I/O Panel & EM-3 Terminal StripINSTALLATION:·Typical for 3 Indoor Light sensors·Connect to same earth ground as EMS panelMOUNTING LOCATION: N/APOWERCOMSIGNAL(3) TYP.INDOOR LIGHT SENSORS (ILS)24 VDCEMS PANEL+-341716AUXILIARY I/O PANEL(RED)(BLACK)(YELLOW)19182120-+-+3rd ILS-+4th ILS(BLACK)(YELLOW)(BLACK)(YELLOW)12ALARMOUTRTU CONNECTION DETAILSCALE: NoneCABLING: 18/2 (Electrical Install)FROM: EM-3 Terminal StripINSTALLATION: Special Instructions1.Terminal designations are for economizer actuator motors. If hvac units do not haveeconomizer section or do not have iaq/dcv option, then do not terminate wires andmake note on survey form.2.Daisy chain to next sales floor hvac unit, as requiredMOUNTING LOCATION: N/AAQAQ1RTUDAMPERMOTOR1015RTUTB1CARRIER/YORKWIRE TO BE LANDED ONECONOMIZERBOARD HH63AW001 (W7212), ASSHOWNLENNOX L SERIESWIRE TO BE LANDED ONTERMINAL TB1, AS SHOWN-+-+P1PRTUQ769CYORK (option 2) WIRE TO BELANDED ON INTERFACEBOARD Q769C AS SHOWN-+12RTUP28TRANE WIRE TO BE LANDEDON TERMINALS,AS SHOWN-+72727272EMPLOYEEOVERRIDE1312EXTERIOROVERRIDE1514EMPLOYEEOVERRIDEEXTERIOROVERRIDECABLING: 18/2 (Electric Install)INSTALLATION: N/AMOUNTING LOCATION: To be determined by customerFROM: EM-3 Terminal Strip433(RED)3(RED)STANDARDOVERRIDEOPTION*OVERRIDEBUTTONDETAILSCALE: None+VD-D+GndShldPHILIPSSERVICE 19FRONT VIEWUNDER COVEREMPLOYEEEXTERIOR20212218CABLING: 18/4 (Electric Install)FROM: EM-3 Terminal StripINSTALLATION: TO BE USED WITH SUBNET 3OVERRIDE COMMUNICATION PORTSMOUNTING LOCATION: To be determined by customer#ANTUMBRAOVERRIDEOPTIONOVERRIDEBUTTONDETAILSCALE: NoneILS WIRING DETAILSCALE: NoneCABLING: 18/4 (Electrical Install)FROM: EM-3 ESC TB1·INSTALLATION: Typical for 1 sensor connectingto terminals in eSC/IFP.MOUNTING LOCATION: I/O connectionsPOWERCOMSIGNAL TERMINALS BLOCK(RED)(BLACK)(YELLOW)34451st (ILS)2nd (ILS)TELETROL SYSTEMS INC. 286 Commercial Street Manchester, NH 03101 DOLLAR TREE FIELD WIRING (FOR REFERENCE ONLY)EM-4 of 4ENERGYMANAGEMENTPLANDRAWN:CHECKED:W.P.C.R.S.R.REVISION: (PART NUMBER 94-327)DATE:10/11/13ADD NEW CONTROLLER TODESIGN (ECN 2167)6/26/14INTERCONNECTION INFORMATION FORAUXILIARY I/O PANEL, 01-451.(ECN 2234)8/13/14ADD ANTUMBRA OPTION.(ECN 2239)*#OVERRIDE WIRING LEGENDDETAIL TAGOVERRIDE USECONNECTION TOTO BE USED WITHSTANDARD OVERRIDEOVERRIDE COMMUNICATIONSUBNETESC I/0 TERMINALSTO BE USED WITHANTUMBRA OVERRIDE