SR0082410 - Laserfiche WebLink

Home Browse Search

to anchor points,and the two strap halves are connected to each other 1.3.7.3.2.The particular configuration of hardware will be determined at the top of the tank.See Figure 1.5. by the contractor,the owner or the owner's representative,but is to adhere 1.3.7.2.11.MOH anchor straps are to be installed in the following way: to the following: Anchoring hardware must be manufactured to industry standards ure 1-5 and dimensions,and sized according to Table 1.3. _ _ • All exposed metal on the anchoring system must be coated IIII- Load Binder Strap Tee IIIII=IIIII or galvanized to protect against corrosion. III II—IIIII Assembly I—IIIII • If the hardware used isnot provided by us,contact the hardware IIIII—I IIIII—IIIII manufacturer or supplier forspecific information on hardware and its use. IIIII=IIIII II=IIIII - IIIII-II MOH IIIII-IIIII Minimum Turnbuckle IIIII—IIIII Strap III—IIIII Tank Diameter(by Type) Minimum Wire Diameter ILII—III IIIII—IIIII Hook Jaw Eye Rope Diameter IIIII=IIIII IIII=IIIII afoot 3/4u 'h1' �h" _3/811 IIIII-1111 ;z� bead'man IIIII=IIIII „ „ „ ° e 6-foot 3/4 1/2 1 1/2 3/8 — — — — —IhIll—M11111E=E9 8-foot 3/a" 3/4" • Iiftthe strap with the hook end down and the hook facing away fro m the tank - • lower the hook end of the strap between the tank and the anchor 10-foot 11/4" 3/a" 3/a" 1h" point,and hook the strap to the anchor point12 foot 1/a" 3/a" 3/4" • put a washer and a blind nut(acorn nut)on one end of the threaded rod. • Feed the rod through the hole in the strap-end connector 1.3.7.3.3.When D-ring/D-ring straps are shipped and turnbuckles • put a washer and a nut on the other end of the threaded rod are ordered from us,we may ship extra hardware that may or may not • centerthe wear plate on the top center line of the marked ribs be necessary with alternate deadmen placement. • lowerthe threaded rod,washer and nut into the channel section 1.3.7.3.4.Locate the anchor points as shown in Figure 1-6 and on the strap-end connector,taking care to place the washer and Table 1-4.Refer to dimensions in Table 1.4.Align(within a tolerance nut on the outside of the connector • hand-tighten the nuts of±1 inch)all anchor points. 1.3.7.2.12.Repeat the bulleted items in 1.3.7.2.12 for the second rod of the assembly. IIIII=IIIII ` I=IIIII 1.3.7.2.13.After the two threaded rods are placed,tighten the threaded IIIII=I IIIII—IIIII rods,using a torque wrench to tighten to 25.30 foot-pounds,or until snug. IIIII=IIIII I I=IIII 1.3.7.2.14.Repeat the bulleted items in 1.3.7.2.12 for each of the load binder assemblies. 1111114111 _____ IIIII=IIIII � III=IIIII 1.3.7.3. HARDWARE AND ANCHOR POINTS IIIII—III IIIII—IIIII 1.3.7.3.1.When our anchoring hardware is not being used,the installing IIIII—IIIII 8 D A IIII=IIII contractor is responsible for providing hardware and anchor pointsIIIII-IIII •°' • • IIIII-IIIII of sufficient size and strength forthe tank being installed. 12" Deadman IIII =IIIII Nominal Tank Diameter A:Strap Eye g:Alternate Dimension C:Strap Length D:Center of Tank To Anchor Point to Center of Deadmen 4-foot 10"[25 cm] not reccommended 100"[254 cm] 31"[79 cm] 6-foot 23"[58 cm] not reccommended 145"[368 cm] 43"[111 cm] 8-foot(Red Tank) 29"[74 cm] 17"[43 cm] 181"[460 cm] 53"[135 cm] 8-foot(Green Tank) 30"[76 cm] 18"[46 cm] 195"[495 cm] 57"[145 cm] 10-foot(Red Tank) 38"[97 cm] 26"[66 cm] 236"[600 cm] 70"[178 cm] 10-foot(Green Tank) 39"[100 cm] 27"[69 cm] 236"[600 cm] 71"[180 cm] 12-foot 46"[117 cm] 34"[86 cm] 271"[688 cm] 88"[224 cm] 10