Laserfiche WebLink
E01 <br /> "�' TECHNICAL BULLETIN <br /> 1% Fft1F* TBO18 <br /> 4*� Franklin Fueling Systems March 1, 2006 <br /> Introducing the MagVFC <br /> FE Petro would like to introduce its next <br /> generation of Variable Frequency Controllers: the <br /> MagVFC. In conjunction with the release of the <br /> MagVFC; we have also introduced the MagShell <br /> 4 HP Variable Speed Pump Motor Assembly <br /> (PMAMVS4), which is the first 4 HP pump motor r 7-Segment <br /> that fits into a 4"tank opening. k-f `, Displays <br /> The MagVFC will also control the existing FE <br /> Petro 2 Horsepower Variable Speed Pump Motor <br /> Assembly (PMAVS2). When the VS4 (4 HP Silence <br /> Variable Speed Pump Motor) is being used the • Button <br /> MagVFC must be powered by 208/230V three <br /> phase input voltage. If the MagVFC is used with a Yellow Com. <br /> 2 HP Variable Speed Motor, it will operate on ==` " LED <br /> single or three phase input power; however, two • R -" - - _ <br /> horsepower performance will be slightly improved - <br /> if three phase input power is used. Reset Button <br /> The MagVFC continues to include the same <br /> popular features as the IST-VFC with several <br /> enhancements. Among these enhancements are: <br /> • Fault Readout - When activated, the <br /> MagVFC will display the last three fault <br /> conditions encountered. . .•- <br /> • Auto Restart from Underload (Dry Run) <br /> Fault-When activated, the MagVFC will attempt to restart and automatically clear the fault on the next hook. <br /> • Extended Run Protection - When activated, the MagVFC will shut the pump off if the pump runs for 60 minutes <br /> with no change in pumping activity. <br /> • Dual seven segment displays that indicate pump operating status and error codes and a yellow LED to indicate <br /> communications activity. <br /> • An audible alarm that indicates fault conditions, but also includes a silence button for acknowledging faults <br /> without clearing them. <br /> • Enhanced serial communication that allows intelligence sharing with INCON fuel management systems. <br /> Compatibility of MagVFC and IST-VFC <br /> • Like the IST-VFC, the MagVFC is only compatible with FE Petro model variable speed motors. <br /> • Although the MagVFC can operate the VS4 and VS2 pump motors, the IST-VFC can only operate the VS2 <br /> models. <br /> • Starting in February of 2006, the MagVFC's communication protocols enable the controller to communicate with <br /> the IST-VFC using a compatibility mode switch setting. This allows both controllers to function in Master/Slave <br /> and Master/Slave Alternating Circuit configurations in cases where an IST-VFC is being replaced by a MagVFC. <br /> This feature is only available on MagVFCs with a software revision of 1.18 or higher. <br /> • Starting in October of 2003, FE Petro's Variable Frequency Controller, the IST-VFC, was replaced by the <br /> MagVFC. <br /> • Please refer to the MagVFC Installation and Owner's Manual for further details regarding installation and <br /> operation of the MagVFC. <br /> • Reference materials are available on our website. Please refer to Service Bulletin 011 and Technical Bulletin <br /> TB0106-1 for further details on compatibility and communication settings. <br /> Please contact Technical Support if we may be of any assistance. <br /> Franklin Fueling Systems • 3760 Marsh Rd. • Madison WI 53718 USA <br /> Tel: +1 608 838 8786 •800 225 9787 • Fax: +1 608 838 6433 •www.franklinfueling.com <br />