Laserfiche WebLink
ARB Approved IOM — Executive Orders VR-201 - G and VR-202 -G ( Swivel Breakaway — 807 ) ITEM #90 <br /> Healy Model 807 Swivel Breakaway <br /> 1/301 <br /> Rv <br /> wmw <br /> IMPORTANT : This sheet must be left with service station manager, <br /> HEALY STAGE II VAPOR RECOVERY MODEL NOZZLE END <br /> 807 SWIVEL BREAKAWAY (HOSE BREAK) <br /> ASSEMBLY & INSTALLATION INSTRUCTIONS <br /> N The Healy Swivel Breakaway is delivered loosely assembled. Handle <br /> carefully to avoid dropping and /or losing the precision parts. N <br /> ■ Failure to remove the Shear screw ( Item 9 ) as described in <br /> Step 1 below could result in fracturing or shearing of the screw <br /> The Shear screw will require replacement if damaged . <br /> ■ Be sure to assemble parts in the exact sequence as shown below , <br /> w � <br /> ■ Be sure to lubricate all o— rings and quad seals where indicated. <br /> Use of ordinary motor oil is sufficient. <br /> ■ Do not use thread — sealing compounds on straight threads. <br /> ■ This Breakaway shall be installed between the product hose <br /> and the nozzle end ( threaded onto nozzle) . <br /> N <br /> V <br /> V <br /> O <br /> ASSEMBLY INSTRUCTIONS <br /> ( refer to diagram at right) <br /> SEE <br /> NOTE <br /> 1 . Remove the Shear Screw ( Item 9) and the packing materials. <br /> Separate the halves of the breakaway assembly, retaining the .--- o <br /> loose internal valve, ( Item 6 ) and the spring (Item 11 ) inside <br /> the halves. <br /> 2. Install the male threaded half of the 807 into the Healy Nozzle. <br /> Lubricate the o— rinq seals (Items 17 & 21 and tiqhten to rn <br /> 35 to 70 foot pounds . Be sure the vapor tube fitting slides easily into <br /> the nozzle before final tightening . <br /> 3. Select the delivery hose, lubricate the o— ring seals and straight <br /> thread . Assemble the non — swivel end of the Breakaway on the <br /> hose. Tighten to 35 to 70 foot pounds. Be sure the valve and spring <br /> (items 6 & 11 ) are in place before final tightening . <br /> 4. Carefully fit both halves of the Breakaway together. Utlizing <br /> the alignment pin, fully compress both halves and insert the HOSE END <br /> Shear Screw ( Item 9 ) and hand tighten . Final tighten to 20 <br /> inch pounds. Tools should not be necessary to initially start <br /> the screws. NOT FIELD REPLACEABLE <br /> 27 2 4125-514GJ QUAD III MINNISOTA RUBBER 80727 <br /> 21 1 1-025 O-RING, PRECISION #5747 13-2 <br /> 20 1 1-122 G-PoNG, PRECISION /9727 709 <br /> 19 2 1-024 O-RING, PRECISION 05747 UPI <br /> i8 1 1-117 O-RING, PRECISION #9727 708 <br /> ® * 17 6 1-012 O-Rl PRECISION 0747 75414 <br /> 16 1 1 -009 0-11 PRECISION #9727 753 <br /> 11 1 A8701-752 SPRING, CONICAL 752 <br /> 9 2 80701 -707 SCREW, SHEAR 787-1 <br /> 8 1 A8701-748 VALVE, DISPENSING END 748 <br /> 4 i 88701 -BIO SH G $10 <br /> O 2 1 CS701 -805 SYAVEL, FEMALE, (MACHINED) 805 <br /> 1 1 66701 -809 BODY, DISPENSER END BOB <br /> NOTE; SHEAR SCREW INSTALLS 45° FROM SPARE, ITEM No, QTY OWG N0. DESCRIPTION Pm <br /> UST OF MATERIAL <br /> HEALY SYSTEMS, INC . healy <br /> 18 Hampshire Drive Hudson, New Hampshire 03051 the SMART Stage II solution <br /> ( 603) 882- 2472 Telephone* (603) 882- 5189 FAX <br /> A8701 .807-INST•M <br /> 11I16�00 REV. Y <br /> Franklin Fueling Systems Website : http : lf/www, fErariklinfuelina , com <br /> 3760 Marsh Road Email : sales@franklinfueling . com <br /> Madison , Wisconsin 53718 USA Telephone : 800-225-9787 <br /> ARB Approved Installation , Operation and Maintenance Manual Fax : 608-838-6433 <br /> HEALY <br /> QFf 0 Franklin Fueling Systems <br />