|
HVAC Equipment Schedule I Till
<br /> EVAPORATOR FAN ELECTRICAL FILTERS COOLING HEATING (GAS) MIN' `
<br /> EAT I LAT EERWT (Ibs) OFM REMARKS �`G�tt�eGts
<br /> MARK MANUF. & MODEL NO. CFM ESP HP BHP MCA MOCP VOLT f HZ TYPE SIZES Btuh T S EAT LAT WB SEER IEER INPUT OUTPUT EAT LAT AFUE
<br /> 28.9 35 208 (2) 11.0 - EXISTI G U TT: a TUNE UNIT WITH N BELTS, LUBRI TIO and REFRIGERANT C RGE b PROVIDE ERV 10 PLEATED FILTERS
<br /> T EXISTING) CARRIER Model 48HJD006 / / / " " " * c VERIFY EXISTING SUPPLY PLENUM SMOKE DETECTOR (ADD IF MISSING d} (NEW) DEMAND CONTROL VENTILATION (CO2) - FIELD INSTALLED SENSOR.
<br /> 5.0 TON ROOFTOP PACKAGE GAS/AC] 1,950 0.57 1.5 1.17 28.9 35 230 3 60 DERV 10 16 x25 x2 61,000 42,700 80 53.5 65 153 13.0 [--] 72,000 59,040 70 105 s23� 714 350 WEIGHT INCLUDES UNIT, ACCESSORIES (ECONOMIZER & SENSORS) AND CURB ROUTE 3/4'�II CONDENSATE DRAIN TO ROOF DRAIN.
<br /> T [EXISTING) CARRIER Model 48WJD006 28.9 Y35
<br /> 208 (2) 11.0 - (EXISTING) UNIT: a TUNE UNIT WITH N BELTS, LUBRICATION and REFRIGERANT CHARGE b PROVIDE N ERV 10 PLEATED FILTERS M I Architects, Inc.
<br /> " 10 16"x25"x2" 61 000 42 700 80 53.5 65 53 13.0 - 72,000 69,440 70 I 1 Q5 82x 714* 340 * c� VERIFY EXISTING SUPPLY PLENUM SMOKE DETECTOR (ADD IF MISSING d) (NEW) DEMAND CONTROL VENTILATION (CO2) - FIELD INSTALLED SENSOR.
<br /> 2 5.0 TON ROOFTOP PACKAGE GAS AC 2,260 0.57 1.5 1,41 28,9 230 3 60 DERV [- ] WEIGHT INCLUDES UNIT, ACCESSORIES (ECONOMIZER & SENSORS) AND CURB I ROUTE 3/4 1 CONDENSATE DRAIN TO ROOF DRAIN. ARCH I TECTURE
<br /> PLANNING
<br /> MANAGEMENT
<br /> DESIGN
<br /> T 34 45 208 (4) 12 45 - FACTORY OPTIONS: a ECONO IZER + BARO ETRIC RELIEF b) 2 ERV 10 STANDARD FILTER PANI�EL c SUPPLY-AIR SPOKE DETECTOR 2221 OLYMPIC BLVD.,
<br /> NEW) CARRIER Model 48HCIA06G2A50B0A0 " 3 60 ER 10 16"x16 x2" 61,875 32,315 80 53.5 65 53 15.20 [---] 60,004 49,000 701 105 813 775* 380 d DEMAND CONTROL VENTILATION (CO2) �- FACTORY INSTALLED SENSOR e) MODIFY EXISTING ROOF CURB AS REQUIRED (FIELD VERIFY) SUITE 100
<br /> 3 5.0 TON ROOFTOP PACKAGE GAS/AC] 2,104 0.55 1.5 1.37 30 45 230 V I WEIGHT INCLUDES UNIT, ACCESSORIES (ECONOMIZER & SENSORS) AND CURB I ROUTE 3/4"0 CONDENSATE DRAIN TO ROOF DRAIN.
<br /> T 30 45 208 (4) 12.46 - FACTORY OPTIONS: a) ECONO IZER + BARO ETRIC RELIEF b 2 ERV 10 STANDARD FILTER PANEL c SUPPLY-AIR SP OKE DETECTOR WALNUT GREEK, GA
<br /> NEW) CARRIER Model 48HCLA06G2A50BOA4 " 60 E 10 16"x16"x2" 62 380 34 320 80 53.5 65 53 15.20 [--] 60,000 49,000 70 1 105 81% 775* 275 * d DEMAND CONTROL VENTILATION (CO2) -- FACTORY INSTALLED SENSOR e) MODIFY EXISTING ROOF CURB AS REQUIRED (FIELD VERIFY) cl45g5
<br /> 4 5.0 TON ROOFTOP PACKAGE GAS/AC] 2,300 0,72 2.0 1.65 30 45 230 3 M = I ( I WEIGHT INCLUDES UNIT, ACCESSORIES (ECONOMIZER & SENSORS) AND CURB I ROUTE 3/4-0 CONDENSATE DRAIN TO ROOF DRAIN. q25-25'7-H-74 Tel
<br /> q25-143-1581 Fax
<br /> a25-878-8875 Cell
<br /> muthana®miarchitect.com
<br /> vv vmlarchItect.com
<br /> Exhaust Fan EF + bake-Up Air (MUA) Schedule Tenant Space Air Balance Summary
<br /> AIR HSONES
<br /> MARK QTY. MANUF. & MODEL NO. CFM SP TEMP RPM BHP VOLT p1 HZ AMPS WATTS WEIGHT SPEED (Spherical) REMARKS EXHAUST SYSTEMS
<br /> EF (EXISTING) Greenheck Model CUE-100 - (EXISTING) ROOF MOULTED EXHAUST FAN WITH CURB, BACKDRAFT DAMPER, BIRD SCREEN AND INTERNAL MOTOR PROTECTION TO REMAIN. EF-1 GENERAL EXHAUST -750 CFM v
<br /> 1 [Restroom & Storage Exhaust] 750 0.30" -- 1,140 1/6 115 1 60 --- --- 54 lbs 1 N6.2
<br /> KlwF-1 TYPE-1 KITCHEN WOOD -2,760 CFM
<br /> -3,510 CFM v x
<br /> MAKE-UP AIR
<br /> v
<br /> 1,50 - SEE ECON-AIR DRA IIS FOR ADDITIONAL SPECIFICATIONS. HVAC OUTSIDE-AIR RTU-1 +350 CFM
<br /> F ECON-AIR Model EABDUI8 HOOD EXHAUST FAN j Wrap SEE SHEETS M4.1 & M4.2 FOR SPECIFICATIONS.
<br /> 1 2,760 1.20" -- 1,116 208 3 60 -- --- 153 lbs 1 13.5 - WRAP EXHAUST PLE U AN DUCTWORK TO HOOD COLLAR WI 3M Fre Barrier Duct HVAC OUTSIDE-AIR RTU-2 +340 CFM
<br /> � pp �yy TTFF�C -
<br /> [Type 1 Hood Exhaust] 065 - PROVIDE INTERLOCK WITH MUA-1 (MAKE-UR AIR UNIT) FOR SIMULTANEOUS OPERATION. HVAC OUTSIDE-AIR RTU-3 +380 CFM O
<br /> HVAC OUTSIDE-AIR RTU-4 +275 CFM v -
<br /> HOOD MAKE-UP AIR MUA- ) +2,484 CFM
<br /> SEE ECON-_AIR DRAWINGS FOR ADDITIONAL SPECIFICATIONS. +3,829 CFM Q �
<br /> U 075
<br /> 1 CHAMPION Model 650ODM MAKE-UP AIR UNIT 2,484 0.50' -- 446 . 115 1 60 8.1 --- 304 lbs 1 -- - PROVIDE INTERLOCK WrrH KEF-1 (TYPE-I HOOD EXHAUST FAN) FOR SIMULTANEOUS OPERATION. NET AIR BALANCE: +319 CFM
<br /> [Type 1 Hood Make-Up Air
<br /> ��
<br /> NOTE: 2!;������-tttttt
<br /> 1) A CERTIFIED AIR BALANCE IS REQUIRED FOR COMMERCIAL o
<br /> KITCHEN HOOD NOTES_ 1. ENSURE EXHAUST FAN (KEF) TERMINATIONS ARE ADEQUATELY SEPARATED FROM NEW AND EXISTING AIR INTAKE UNITS TO AVOID EXHAUST AIR INTAKE INTO BUILDING - FIELD VERIFY. KITCHENS AND REPLACEMENT AIR PER CMC Section 511.3.1. _
<br /> 2. EXHAUST FAN (EF) AND HOOD MAKE-UP AIR UNITS (MUA) SHALL BE INTERLOCKED FOR SIMULTANEOUS OPERATION. O Q
<br /> 3. GREASE FOOD EXHAUST FAN (KEF) SHALL CONTAIN ALL GREASE - UNDER NO CIRCUMSTANCE MAY GREASE CONTAMINATE THE ROOF. 2) TENANT SPACE IS SLIGHTLY PRESSURIZED [+319 CFM] t�d z
<br /> WHICH IS DESIRABLE FOR RETAIL/FOOD SERVICE OCCUPANCY. o 0 0
<br /> >O
<br /> z
<br /> z
<br /> Mechanical General Notes Duct Smoke Detector Notes:
<br /> 1. ALL WORK SHALL BE EQUAL OR SUPERIOR TO THAT REQUIRED BY 10, ALL RIGID DUCTWORK SHALL BE SEALED AIR TIGHT WITH 6 OUNCE I. THE INSTALLATION OF DUCT SMOKE DETECTORS FOR
<br /> AUTOMATIC SHUT DOWN of AIR MOVING SYSTEMS
<br /> APPLICABLE CODES: CANVAS SOAKED IN AEROBAL OR 4" HARDCAST TAPE.
<br /> - 2016 California Building Code Part 2 NO DUCT TAPE IS APPROVED FOR RIGID DUCT USE. REQUIRED BY CMC See609.0 OR AS REQUIRED
<br /> - 2016 California Electrical Code Part 3 FOR THE OPERATION ofFFIR -SMOKE DAMPERS SHALL t
<br /> ion
<br /> tL
<br /> - 2016 California Mechanical Code Part 4 11. FACTORY-MAKE FLEXIBLE AIR DUCTS AND CONNECTORS SHALL NOT BE COMPLY WITH THE REQUIREMENTS OF CITY OF LATHROP z
<br /> - Part 5 MORE THAN FIVE (5) FEET IN LENGTH AND SHALL NOT BE USED IN FIRE: DEPARTMENT'S GUIDELINES.
<br /> 2016 California Plumbing Code LIEU OF RIGID ELBOWS OR FITTINGS PER 2016 CMC Section 603.4.1.
<br /> - 2016 California Energy Code (Title 24) Part 6 - EXCEPTION' RESIDENTIAL OCCUPANCIES �HERE- 2016 California Fire Code I Part 9 - FLEXIBLE AIR DUCTS AND CONNECTIONS SHALL COMPLY WITH 2. AIR DUCT SMOKE DETECTORS SERVING AIR-
<br /> - 2016 California Green Buildin Standards Part 11 UL 181 A D SHALL BE INSTALLED IN ACCORDANCE WITH OVING SYSTEMS ARE INSTALLED WITHIN CONCEALED
<br /> - Adopted FPA Manuals g I MANUFACTURER'S INSTALLATION INSTRUCTIONS AND "SMACNA SPACES, AND/OR DROP CEILING AREAS, THE DETECTOR O �0 z
<br /> P N SHALL BE PROVIDED WITH A REMOTE ALARM LED m
<br /> -- SMACNA Standards for Ductwork, Materials & Instaliation HVAC Duct Construction Standards �•- Metal and Flexible." DEVICE MOUNTED ON THE CEILING TILE DIRECTLY F" U
<br /> - CONFLICTS SHALL BE BROUGHT TO THE DESIGNER'S ATTENTION FLEXIBLE AIR CONNECTOR LENGTHS SHALL NOT BE MORE
<br /> FOR CLARIFICATION PRIOR TO THE SUBMISSION OF THE BID. THAN FIVE (5) FEET AND SHALL. NOT PENETRATE A WALL, BELOW THE UNIT SERVED. �
<br /> FLOOR OR CEILING PER 2016 CMC Section 603.5. v
<br /> 2. CONTRACTOR SHALL NOT ALLOW OR CAUSE ANY OF HIS WORK TO BE
<br /> 3. SAID REMOTE ALARM LED DEVICE SHALL BE LABELED z i�
<br /> COVERED UP OR ENCLOSED UNTIL IT HAS BEEN REVIEWED AND/OR 12. VOLUME DAMPERS SHALL BE PROVIDED AT ALL SUPPLY AIR BRANCH TO CLEARLY IDENTIFY THE UNIT SERVED (RTU-3, ETC.). w 6
<br /> D BY TAKEOFFS - UNLESS OPPOSED-BLADE-DAMPERS (OBD) ARE SPECIFIED
<br /> TESTS WITNESSED BY OWNERS REPRESENTATIVEAN V 1 O
<br /> GOVERNMENT AUTHORITIES HAVING JURISDICTION OVER HIS/HER WORK. ON THE PLANS. 4. WHERE AIR DUCT SMOKE DETECTORS SERVING AIR- f_z D
<br /> PRIOR TO BIDDING TO 13. ALL RECTANGULAR DUCTWORK ELBOWS SHALL BE PROVIDED WITH
<br /> 3. EXAMINE THE SITE AND PREMISES Rla MOVING SYSTEMS ARE INSTALLED IN CONCEALED SPACES,N AND/OR DROP CEILING AREAS MORE THAT 10 FEET i f l
<br /> DETERMINE CONDITIONS UNDER WHICH THE WORK IS TO BE TURNING VANES. ABOVE THE FINISHED FLOOR, THE DETECTOR SHALL BE
<br /> PERFORMED. NO ALLOWANCE WILL BE MADE FOR EXTRA EXPENSE PROVIDED WITH A REMOTE TEST AND RESET SWITCH.
<br /> INCURRED DUE TO FAILURE TO EXAMINE THE PREMISES OR TO 14. SUBMIT TWO SETS OF OPERATION AND MAINTENANCE MANUALS AND
<br /> DISCOVER SITE CONDITIONS WHICH AFFECT THE WORK. AS--BUILT PLANS TO OWNER'S REPRESENTATIVE AT COMPLETION OF
<br /> PROJECT. 5. SAID REMOTE TEST AND RESET SWITCH SHALL BE
<br /> 4, UPON COMPLETION OF THE WORK, AND AS PRECEDENT TO FINAL ATTACHED TO AN ADJACENT WALL OR STRUCTURAL (�
<br /> PAYMENT, THE SUBCONTRACTOR SHALL DELIVER TO THE OWNER'S 15. CONTRACTOR WILL RETURN ALL WARRANTY CARDS TO APPLICABLE COLUMN AT A MAXIMUM HEIGHT OF 6 FEET ABOVE V U LLLL
<br /> REPRESENTATIVE, ORIGINALS OF ALL DRAWINGS SHOWING THE MANUFACTURER AND WILL LEAVE ONE (1) COPY OF INSTALLATION
<br /> WORK EXACTLY AS INSTALLED. THE SUBCONTRACTOR SHALL ALSO AND SERVICE INSTRUCTIONS FOR ALL EQUIPMENT WITH THE FINISHED FLOOR.
<br /> TO THE OWNER'S REPRESS 1 Q
<br /> DELIVER WN REPRESENTATIVE N ONE ( ) COMPLETE OWNER.
<br /> SET OF REPRODUCIBLE DRAWINGS SHORING THE WORK EXACTLY AS T z Q
<br /> INSTALLED. 16. CONTRACTOR SHALL GUARANTEE ALL MATERIALS AND WORKMANSHIP <Q
<br /> FOR A PERIOD OF ONE (1) YEAR FROM DATE OF ACCEPTANCE.
<br /> 5. AT THE COMPLETION OF THE WORK, CLEAN AND RID THE PROJECT Val
<br /> AND THE SURROUNDING AREAS OF ALL DEBRIS, SCRAP AND 17. CONTRACTOR SHALL AIR BALANCE THE SUPPLY AND RETURN AIR
<br /> SYSTEMS AS SHO 0 PLANS AS REQUIRED BY ALL LOCAL CODES
<br /> MATERIALS RELATED TO HIS/HER WORK. SHOULD THE GENERAL M WN N
<br /> CONTRACTOR BE REQUIRED TO CLEAN MECHANICAL CONTRACTOR'S AND REGULATIONS. Q
<br /> DEBRIS AND MATERIAL, THE MECHANICAL CONTRACTOR MAY BE 18. CONNECTIONS 13" EN METAL DUCTS AND THE INNER CORE OF FLEXIBLE
<br /> CHARGED FOR THIS SERVICE. DUCTS SHALL BE MECHANICALLY FASTENED. OPENINGS SHALL BE SEALED
<br /> 6. ALL MATERIALS SHALL BE NEW AND IN PERFECT CONDITION, WITH MASTIC, TAPE, AEROSOL SEALANT, OR OTHER DUCT-CLOSURE SYSTEM
<br /> EXCEPT AS NOTED OTHERWISE. THAT MEETS THE APPLICABLE REQUIREMENTS OF UL 181, UL 181A, OR
<br /> UL 181B AS PER CEC Energy Efficiency Standards, Section 124(x). �(tOf SS/1
<br /> 7. THERMOSTATS SHALL BE MOUNTED 4'-0" ABOVE FINISHED FLOOR " FOR THE
<br /> �4'��0�'�
<br /> OR AS NOTED ON PLAN. ALL THERMOSTATS SHALL HAVE CLEAR 19. PRIOR TO THE ISSUANCE OFA CERTIFICATE OF OCCUPANCY"
<br /> PLASTIC OR BLANK LOCKING COVERS, PULL A MINIMUM OF 8 BUILDING, OUTSIDE AIR CERTIFICATION OR SYSTEM AIR BALANCING SHALL `�
<br /> WIRES BETWEEN UNIT AND THERMOSTAT TO ALLOW FOR FUTURE. BE COMPLETED AND DOCUMENTED PER CEC Energy Efficiency Standards, M 30514 r•,
<br /> ap s/ao/so y
<br /> Section 121(f).
<br /> 8. GENERAL BUILDING EXHAUST AIR DUCTWORK SHALL BE GALVANIZED 20 DOMESTIC CLOTHES DRYER MOISTURE EXHAUST DUCTS SHALL BE Of METAL
<br /> SHEET METAL OR ALUMINUM FLEX DUCTWORK. PROVIDE BACKDRAFT ��9 FCHANIOP ,
<br /> DAMPERS FOR ALL EXHAUST FANS AND RELIEF VENTS. AND SHALL HAVE SMOOTH INTERIOR SURFACES PER 2016 CMC Section 504.4. �' F Fa
<br /> 9. ALL RIGID SUPPLY AND RETURN AIR DUCTWORK FROM UNITS SHALL
<br /> BE LINED GALVANIZED SHEET METAL OR RIGID FIBERGLASS DUCT
<br /> BOARD, LINING SHALL BE MINIMUM OF 1" THICK (1-1/2" WHEN i5e�FOR PLAN 2Uc K
<br /> OUTDOORS), ATTACHED WITH ADHESIVE AND GRIP-NAIL --
<br /> F�QR
<br /> MECHANICAL FASTENERS. DUCTWORK INSULATION SHALL SATISFY R G
<br /> 15�UED fi'LANhElhMS
<br /> THE REQUIREMENTS OF CHAPTER 6, SECTION 604 OF THE
<br /> CALIFORNIA MECHANICAL CODE. FIBERGLASS DUCT BOARD SHALL BE
<br /> INSTALLED IN ACCORDANCE WITH THE MANUFACTURER'S
<br /> RECOMMENDATIONS. NO. DATET7ESc7RIt'fION
<br /> A DUCT SIZES SHOWN WITH LINED DUCT IS THE INSIDE
<br /> DIMENSION. Consulting
<br /> B. DUCT SIZES SHOWN AS ROUND DUCT IS THE INSIDE
<br /> Engineer
<br /> DIMENSION. The
<br /> C. PAINT INSIDE OF DUCTS VISIBLE THROUGH GRILLE FLAT
<br /> McDermott '
<br /> BLACK.
<br /> roup
<br /> D. ALL RIGID DUCTWORK IN NON--CONDrrIONED SPACES SHALL
<br /> Mechanical
<br /> McDermott
<br /> Design Notes & Schedules
<br /> Valley Energy ConsufLnnEs
<br /> "Fnruix'x vx�wNc �n[u pcxur m�v+cc
<br /> HAVE A MINIMUM R-6 DUCT INSULATION (OR PER TITLE 24).
<br /> ' o MI cHrNICAL CKCWY°°"SU""° PROJECT#: MGD-Ig032
<br /> ENGINEERING
<br /> ENERGY COMPLIANCE DRAWN: MPM CHECKED: MPM
<br /> CONSULTING
<br /> BUILDING SCALE: A6 NOTED DATE:
<br /> DESIGN
<br /> THE McDermott GROUP
<br /> 2201 FRANCISCO DRIVE, SUITE 140-451 M2
<br /> ELDORADO HILLS, CA 95762
<br /> PHONE: (916) 933-5791
<br /> SHEET OF
<br />
|