|
authorized, substances or components, soil or other CAUTION
<br /> surface or subsurface conditions, or fire, flood, storm , Do not remove elastic band from around float until
<br /> lightning, earthquake, accident or any other conditions, instructed to do so, as damage to valve may result.
<br /> events or circumstances beyond OPW`s control . WARNING
<br /> THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER Failure to properly connect delivery hose and el-
<br /> WARRANTIES, EXPRESS OR IMPLIED, AND ALL OTHER bow, and/or disconnecting a liquid filled delivery
<br /> WARRANTIES INCLUDING, WITHOUT LIMITATION, THE hose or elbow will result in a hazardous spill, which
<br /> WARRANTIES OF MERCHANTABILITY AND FITNESS FOR may result in personal injury, property damage, fire,
<br /> A PARTICULAR PURPOSE, ARE HEREBY EXCLUDED. explosion, and water and soil pollution .
<br /> OPW shall have no other liability whatsoever, whether . Make sure all connections, including the hose and
<br /> based on breach of contract, negligence, gross negli- elbow connections, between storage tank and
<br /> Bence, strict liability or any other claim, including, with- transport are securely coupled .
<br /> out limitation, for special , incidental, consequential or
<br /> exemplary damages or for the cost of labor, freight, ex- • Make sure the lip seal and/or all gaskets in the deliv-
<br /> cavation , clean -up, downtime, removal, reinstallation , ery elbow are properly in place to prevent spills ,
<br /> loss of profit, or any other cost or charges , No person or o Do not operate with damaged or missing parts,
<br /> entity is authorized to assume on behalf of OPW any which prevent tight connections.
<br /> liability beyond this limited warranty. This limited war-
<br /> ranty is not assignable. Normal Operation : A Hose "Kick" and reduced flow
<br /> signal that the tank is full. Close transport delivery
<br /> ** Date of manufacture on this product is located on valve and drain hose into tank before disconnecting
<br /> the flat area of the valve body, under float. any hose fitting .
<br /> Overfilled Tank: Failure of the hose to drain after clos-
<br /> GENERAL INSTRUCTIONS ing the delivery valve signals an overfilled tank. Do Not
<br /> The OPW 71 SO Overfill Prevention Valve is designed for Disconnect any delivery hose fitting until the liquid lev-
<br /> tight fill, gravity drop applications to help prevent acci- el in the tank has been lowered to allow the hose to
<br /> dental or intentional overfilling of underground storage drain into the tank.
<br /> tanks . It is installed in the UST drop tube in place of a WARNING
<br /> standard drop tube . In the event you are splashed with fuel remove wet
<br /> The main 71 SO valve closes when liquid reaches the clothing immediately. Skin contact with gasoline
<br /> initial shut off point. A small bypass valve remains open can cause chemical burns and may result in inhala-
<br /> to allow the delivery hose to drain at 3-5 gallons per tion of vapors that may be fatal . Never go inside
<br /> minute. If the delivery truck valve is not closed after confined areas after being splashed and never go
<br /> initial shut-off, the bypass valve will close and will re- near ignition sources.
<br /> strict all fuel delivery to ensure that the top of the tank IMPORTANT
<br /> is not wetted per EPA requirements. Determine if the underground storage tank is equipped
<br /> The 71 SO models of the 71 SO are designed to be in- with a ball float vent valve, as illustrated in Figure 24. In
<br /> stalled with the following OPW products: Face Seal all systems, the shut-off point of the 71 SO must be
<br /> Adaptor, OPW Spill Container or Multi- port, Jack Screw reached before the ball float reduces flow to ensure
<br /> Kit, Rotatable Product Adaptor, and Product Cap . proper overfill valve operation .
<br /> j IMPORTANT TOOLS NEEDED FOR INSTALLATION AND ASSEM
<br /> IRead these assembly and installation instructions com- BLY;
<br /> pletely and carefully prior to starting . Check to make 1 : 7150-TOOL or 71 SO-TOOLC or
<br /> sure all parts have been provided . Use only the parts
<br /> supplied , substitution of parts may cause product fail- 71 SO-TOOLCT (includes the following)
<br /> ure. • Sharp 3/ 16" drill bit with stop
<br /> Failure to follow instructions may cause improper prod- . Punch
<br /> uct operation or premature failure which may permit NOTE: Testable 71 SO models ending with a "T" re-
<br /> storage tank overfill . An overfilled storage tank may quire the 71 SO-TOOLCT or modified 71 SO-TOOL or
<br /> create hazardous conditions and/or environmental con- 71 SO-TOOLC
<br /> tamination .
<br /> 2
<br />
|