COMPLIANCE INFO_2021 - Laserfiche WebLink

Home Browse Search

Certificate Number:02-019A24 Page 2 of 19 Gilbarco,Inc. Retail Motor Fuel Dispenser(RMFD)/Nxx Series Application: For use in dispensing standard fuels such as gasoline, gasoline with up to 15% ethanol and gasoline with up to 15% methanol blend types and diesel fuel,fuel oil,kerosene and up to 20%biodiesel products as indicted in Section C. "Product Families for Meters" table in NCWM Publication 14,Measuring Devices at retail service stations, attended or unattended,with approved and compatible equipment.Units equipped with the T19976-GX or V3 meter are additionally rated for up to E25.Units equipped with the Gilbarco T9796 G5 meter are additionally approved for dispensing alternate fuels such as gasoline with greater than 25%Ethanol and diesel with greater that 20%biodiesel(i.e.up to 100%Ethanol and 100%Bio-diesel).The Ultra High series with the LC M5 meter are approved to dispense gasoline and diesel fuels. These dispensers are approved for use with Phase E vapor recovery equipment and approved booted or bootless nozzles when the system and components are certified and comply with the zero-set-back interlock requirements.Gilbarco self-contained dispensers(unit with a pump and a motor)are provided with onboard automatic air elimination. Gilbarco remote dispensers(units do not have motor and pump)require the use of a remotely located pump. These remote dispensers require automatic air elimination at the remote pump/STP,or the use of a low product cut off that will prevent air from entering the pump if the fluid level in the tank falls below a point that air could be ingested into the system or the use of other automatic means to prevent air from entering the system. Identification: The identification badge,metal or a self-destructive badge is on the lower base plate below the access panel covering the hydraulics cabinet or located behind the locked main options door.Optional features are indicated on the identification plate. Sealin : The Encore Series device has no remote configuration capability and is classified as a Category 2 device. Access to all metrological features and functions are controlled through the use of a sealable security switch. The security switch has two positions, "normal/sealed" and "calibration/configuration." When the security switch is in the "calibration/configuration" position, sealable parameters including meter calibration,gallon/liter settings,and blend ratio settings can be accessed.Access to sealable parameters is prevented by placing the security switch in the "normal/sealed" position and threading a wire security seal through the cover,which fits over the security switch.The wire security seal must be broken in order to lift the hinged cover and to move the security switch to the "calibration/configuration" position. The security switch and Manager's keypad are located behind the locked main options door. Access to the security switch and Manager's keypad requires opening the options door. Due to security concerns and theft issues, many stations have removed the Manager's Keypad from the unit. W&Ms officials may need to contact station personnel to obtain this keypad. Gilbarco will provide Manager's keypad(s)to each site. The Gilbarco T20453-GX ECO meter or M07300A001, M07300A002, M07300A003, M0730OA005 or M0730OA006 E-Meter Model (NTEP CC 02-040A3) is located in the side column, and does not have any adjustable or metrological calibration features. Gilbarco provides a factory installed, tamper evident decal/seal containing the Gilbarco Inc. name, Trademark or logo, and a non- repetitive serial number.(See Operation) Encore "S" series may also have a user provided lock that must be accessed. The locked lower hydraulics door must be removed to access the user provided lock.This locks a"tool box"type latch that secures the main door.To access features located behind the main door first remove the lower hydraulics door,then unlatch the main door's"tool box"latch,then open the main door. The main door is secured with a lock/key and the lock is located on the left side of the door. Electronic calibration (E-cal): Access to the electronic calibration feature is through the security switch described above. With the switch in the "calibration/configuration" position, a calibration code and the volume of the volumetric standard are entered into the keypad next to the security switch.Product is then dispensed into the standard,a delivery error is determined in cubic inches, and the error value is entered into the keypad. The security switch is then returned to the normal operating("normal/sealed")position and the switch cover is sealed with a wire security seal. Gallon/Liter setting: Access to the gallon/liter setting is through the security switch described above. With the switch in the "calibration/configuration" position, a conversion factor is used to program all Encore® Series dispensers to indicate in gallons or liters. Gallon/Liter setting information can also be viewed without entering the configuration mode. With the switch in the "normal/sealed" position, the number of times that the conversion factor has been changed since the initial installation can be displayed in the main"Volume" display by pressing "ENTER" on the manager's keypad. Press any other key to revert to the normal display.See"examples"shown below. Blend ratio setting:Access to the blend ratio setting is through the security switch described above.On customer-selectable and fixed- blenders,the individual blend ratios for each grade may be programmed at the dispenser. Blend ratio information can also be viewed