|
REVISIONS BY
<br /> SPECIFICATIONS
<br /> 1. SCOPE: THE WORK OF THIS SECTION INCLUDES EVERYTHING NECESSARY GENERAL NOTES GENERAL LIGHTING FIXTURE COMMENTS SYMBOL LIST
<br /> FOR AND INCIDENTAL TO EXECUTING AND COMPLETING ELECTRICAL WORK, 1. ALL WORK SHALL COMPLY WITH THE STATE OF CALIFORNIA, TITLE 24 AND ALL
<br /> EXCEPT AS OTHERWISE HEREINAFTER SPECIFICALLY EXCLUDED. OTHER GOVERNING CODES AND ORDINANCES. 2019 CEC.& 2019 CALIFORNIA 1. All ballasts shall be HPF, C.B.M. - E.T.I. certified, class-
<br /> ENERGY CODE. P equal to universal "Energy saver" VLH series, of quietest HOME RUN
<br /> 2. GUARANTEE: CONTRACTOR SHAH_ PROVIDE TO THE OWNER A WRITTEN sound rating available. Provide low temperature ballasts CONDUIT CONCEALED IN WALL OR CEILING UNLESS NOTED
<br /> GUARANTEE, IN COMPLIANCE WITH DIVISION 1, AGAINST DEFECTS IN 2a. ELECTRICAL SWITCHES AND CONTROLS/MOUNTING HEIGHTS/DISABLED ACCESS: for outdoor mounted fixtures. _ _ _ CONDUIT CONCEALED IN WALL, FLOOR,
<br /> MATERIAL AND WORKMANSHIP FOR ONE (1) YEAR, UPON FINAL ACCEPTANCE 2019 CSC NOW REQUIRES CONTROLS AND SWITCHES INTENDED UNDERGROUND OR UNDER FLOOR UNLESS NOTED
<br /> OF PROJECT BY OWNER. TO BE USED BY OCCUPANTS OF THE ROOM OR AREA TO BE LOCATED: 2. Contractor shall be responsible for ordering proper types of
<br /> 2a.1 NO MORE THAN 48-INCHES, MEASURED FROM THE TOP OF THE OUTLET BOX, trim for all recessed led fixtures and incandescent HOME RUN TO PANEL
<br /> 3. TESTING AND ADJUSTMENT: UPON COMPLETION OF ALL ELECTRICAL WORK, fixtures to fit the ceiling being installed. Finish trims HASH MARKS INDICATE QUANTITY OF CONDUCTORS. k
<br /> ELECTRICAL CONTRACTOR SHALL ADJUST AND TEST ALL CIRCUITS, 2a.2 NO LESS THAN 15 INCHES, MEASURED FROM THE BOTTOM OF THE OUTLET of all recessed led fixtures shall match ceiling #10 NO HASH MARK INDICATES 1/2"C-2#12&1#12GROUND
<br /> OUTLETS, SWITCHES, LIGHTS, MOTORS AND ANY OTHER ELECTRICAL ITEMS finish as directed by architect. 10 INDICATES 10 AWG CONDUCTORS,
<br /> TO INSURE PERFECT OPERATION OF ALL ELECTRICAL EQUIPMENT. ITEMS, BOX, TO THE LEVEL OF THE FINISHED FLOOR OR WORKING PLATFORM. # #
<br /> 3. The contractor shall verify the type of ceiling before SIZE OF CONDUIT SHALL BASE ON N.E. CODE. o T?
<br /> FIXTURES AND PARTS IN NEED OF CORRECTION AND DISCOVERED DURING co rn
<br /> SUCH TESTING SHAD. BE IMMEDIATELY REPAIRED OR REPLACED WITH ALL 2b. ELECTRICAL RECEPTACLE OUTLETS/MOUTING HEIGHTS/DISABLED ACCESS: ordering any fixtures. He is fully responsible to provide all ROOM NUMBER C.O. CONDUIT ONLY
<br /> NEW EQUIPMENT AND THAT PART OF THE SYSTEM SHALL THEN BE RETESTED. 2019 CBC REQUIRES ELECTRICAL RECEPTACLE OUTLETS ON mounting brackets for all ceiling conditions, at no N.I.C. NOT IN CONSTRUCTION c;, o�
<br /> ALL SUCH REPLACEMENT OR REPAIR SHALL BE DONE AT NO ADDITIONAL BRANCH CIRCUITS OF 30 AMPERES OR LESS AND COMMUNICATION SYSTEM extra charge to the owner. � �
<br /> RECEPTACLETO BE LOCATED:
<br /> W.P. WEATHER PROOF N.T.S. NOT TO SCALE
<br /> U
<br /> COST TO THE OWNER. 2b.1 NO MORE THAN 48-INCHES, MEASURED FROM THE TOP OF THE RECEPTACLE 4. All fixtures shall bear U.L label. 5" BOX 4 11/16" SQ.X2 1/8" D.BOX CONDUIT UP z A- ca co
<br /> OUTLET BOX OR RECEPTACLE HOUSING. 5. Acrylic lens shall be 100% pure, virgin, acrylic. V.L. VERIFY LOCATION CONDUIT DOWN � �-
<br /> 4. SITE INSPECTION: THE CONTRACTOR SHAH_ CAREFULLY EXAMINE THE SITE 2b.2 NO LESS THAN 15-INCHES, MEASURED FROM THE BOTTOM OF RECEPTACLE E-+
<br /> AND EXISTING BUILDINGS, SHALL COMPARE THE DRAWINGS WITH THE OUTLET BOX OR RECEPTACLE HOUSING, TO THE LEVEL OF THE FINISHED FLOOR 6. All lighting fixtures shall be installed in accordance with w
<br /> EXISTING ELECTRICAL INSTALLATIONS, AND SHALL THOROUGHLY OR WORKING PLATFORM. the manufacturers Instructions. SINGLE POLE TOGGLE SWITCH SEE NOTE 2a E+ �.
<br /> FAMILIARIZE HIMSELF WITH ALL EXISTING CONDITIONS WITHIN THE SCOPE
<br /> OF THIS WORK. BY THE ACT OF SUBMITTING A BID, THE CONTRACTOR 3. REFER TO THE ARCHITECTURAL REFLECTED CEILING PLAN FOR THE EXACT TYPE 7. Recessed fixtures in fire rated ceiling shall be approved $o,b SINGLE POLE SW,SUBSCRIPT INDICATES OUTLETS CONTR'LD
<br /> WILL BE DEEMED TO HAVE MADE SUCH EXAMINATION AND TO HAVE ACCEPTED AND LOCATION OF LIGHT FIXTURES. for the fire rating of the ceiling. PROVIDE SEPARATE SW. FOR EACH IN GANG ASSEMBLY SEE NOTE 2a o
<br /> SUCH CONDITIONS, AND TO HAVE MADE ALLOWANCE THEREOF IN PREPARING 8. Fixtures in luminous ceiling of ceiling cavities or soffites TWO POLE SWITCH SEE NOTE 2a
<br /> HIS FIGURE. 4. REFER TO THE ARCHITECTURAL POWER AND TELEPHONE PLAN FOR THE EXACT shall be approved for type of installation. THREE WAY SWITCH SEE NOTE 2a w
<br /> LOCATION AND MOUNTING HEIGHTS AND TYPES OF ALL OUTLETS (RECEPTACLES, FOUR WAY SWITCH SEE NOTE 2a 'z' o as
<br /> 5. LOCATIONS AND ACCESSIBILITY: CONTRACTOR SHALL FULLY INFORM TELEPHONES, CRT'S, CLOCKS, ETC.). 9. Stem lengths pendent fixtures shall be one piece without Z -0
<br /> HIMSELF REGARDING PECULIARITIES AND LIMITATIONS OF THE SPACES 5. ALL ELECTRICAL WORK, ITEMS, DEIVCES, ETC. SHALL CONFORM TO THE REQUIRE- couplings, with finish to match canopy and with swivel OCCUPANCY SENSOR SWITCH SEE NOTE 2a
<br /> as 2 .9
<br /> hanger legally approved for weight supported and for SINGLE POLE DIMMER SWITCH SEE NOTE 2a w ' U-�
<br /> AVAILABLE FOR INSTALLATION OF WORK AND MATERIALS FURNISHED AND MENTS OF THE BASE BUILDING SPECIFICATION.
<br /> INSTALLED UNDER THIS DIVISION. DRAWINGS INDICATE DESIRED earthquake protection. Provide wedge type canopy for A a
<br /> • DUPLEX CONVENIENCE OUTLET SEE NOTE 2b H � w
<br /> LOCATION AND ARRANGEMENT OF PIPING, EQUIPMENT, AND OTHER ITEMS, 6. ALL OUTLETS SHALL BE INSTALLED AT THE HEIGHTS INDICATES ON THE SYMBOL fixtures to be installed on sloped ceiling. :�
<br /> AND ARE TO BE FOLLOWED AS CLOSELY AS POSSIBLE. WORK SPECIFIED UST UNLESS OTHERWISE NOTED ON THE DRAWINGS. 10. Outdoor fixtures and fixtures installed in damp location 20A-250V TWISTtOCK RECEPTACLE SEE NOTE 2b w c, w l �' �'a
<br /> AND NOT CLEARLY DEFINED BY DRAWINGS SHALL BE INSTALLED AND shall be approved for wet locations. w `co co
<br /> tx ,�
<br /> ARRANGED IN A MANNER SATISFACTORY TO ARCHITECT, THEY SHAH_ BE 7. EVERY OUTLET HEIGHT SHALL BE VERIFIED ON EACH WALL WITH THE ARCHITECT RECEPTACLE GROUND-FAULT CIRCUIT INTERRUPTER W ® � CQ � ww
<br /> MADE BY CONTRACTOR WITHOUT ADDITIONAL CHARGES, PROVIDED THE OR INTERIOR DESIGNER TO ENSURE THE PROPER HEIGHT AND LOCATION WITH 11. Verify letter size and color of internally illuminated exit J JUNCTION BOX a
<br /> CHANGE IS ORDERED BEFORE WORK IS INSTALLED AND NO EXTRA MATERIAL RESPECT TO CABINET, EQUIPMENT, ETC. signs with local authorities prior to submittal of shop SHOW WINDOW RECEPTACLE
<br /> ARE REQUIRED. drawings. MOTOR
<br /> 8. ALL WORK/MATERIALS SHOWN ON PLANS SHALL BE NEW UNLESS OTHERWISE 12. Recessed fixtures shall be pre-wired to attached J-Box in
<br /> 6. CLEANUP: AFTER COMPLETION OF WORK UNDER THIS SECTION, CLEAN UP INDICATED. accordance with local code requirements. Fixtures shall be TIME CLOCK
<br /> approved for the maximum number of wires going in and out OVERRIDE SWITCH
<br /> ALL RESULTANT DEBRIS FROM THIS WORK AND REMOVE FROM THE SITE.
<br /> 9. UNLESS INSTRUCTED OTHERWISE, THE ELECTRICAL CONTRACTOR SHALL OBTAIN AND of the fixtures as shown on pians. Attached J-Boxes shall ® MAIN SWITCHBOARD
<br /> PAY FOR ALL PERMITS, LICENSES, AND FEES REQUIRED FOR INSTALLATION OF be accessible per C.E.C.
<br /> 7. CUTTING AND PATCHING: THE CONTRACTOR SHALL DO ALL CUTTING AND THE ELECTRICAL WORK. FURNISH FINAL CERTIFICATE OF INSPECTION OR ® POWER PANEL
<br /> PATCHING OF THE EXISTING CONSTRUCTION WORK WHICH MAY BE REQUIRED WRITTEN EVIDENCE OF ACCEPTANCE BY INSPECTION AUTHORITIES FOR ALL WORK 13. ALL LIGHTING FIXTURES ARE TO BE CERTIFIED BY CALIFORNIA FUSE DISCONNECT SWITCH
<br /> FOR THE PROPER INSTALLATION OF THE ELECTRICAL WORK. ALL PATCHING INSTALLED. ENERGY COMMISSION. OCCUPANCY SENSOR
<br /> SHALL BE OF THE SAME MATERIALS, WORKMANSHIP AND FINISH AS, AND SYSTEM SMOKE DETECTOR
<br /> SHALL ACCURATELY MATCH ALL SURROUNDING WORK. 10. BEFORE STARTING ANY WORK, THE ELECTRICAL CONTRACTOR SHALL EXAMINE THE CARBON MONOXIDE DETECTOR
<br /> COMPLETE SET OF DRAWINGS FOR ALL TRADES, INCLUDING ARCHITECTURAL,
<br /> 8. DRAWINGS AND SPECIFICATIONS: ELECTRICAL DRAWINGS ARE HEATING-VENTILATING-AIR CONDITIONING AND PLUMBING. VERIFY ALL DIMEN- PHOTOSENSOR
<br /> DIAGRAMMATIC IN SOME RESPECTS. SIZES AND LOCATION OF EQUIPMENT =O RECEPTACLE 230V 20A UNLESS NOTED
<br /> AND WIRING ARE SHOWN TO SCALE WHERE POSSIBLE, BUT MAY BE SIONS, SPACE REQUIREMENTS AND POINTS OF CONNECTION TO ALL EQUIPMENT. RECEPTACLE NEMA TYPE MATCH WITH EQUIPMENT
<br /> DISTORTED FOR CLARITY ON THE DRAWINGS. FINAL LOCATIONS OF MAKE ANY MINOR ADJUSTMENTS NECESSARY TO AVOID CONFLICT WITH THE EXHAUST FAN
<br /> OUTLETS AND EQUIPMENT SHALL BE AS SHOWN IN ENLARGED DETAILS OR AS BUILDING STRUCTURE AND THE WORK OF OTHER TRADES.
<br /> ® EXIT SIGN
<br /> APPROVED BY THE LIGHTING CONSULTANT. IT IS NOT WITHIN THE SCOPE
<br /> 11. UPDATE PANEL CARDS INDICATING CIRCUIT'S SPECIFIC FUNCTION/LOCATION. DEMAND RESPONSIVE CONTROL SYSTEM
<br /> OF DRAWINGS TO SHOW ALL NECESSARY BENDS, OFFSETS, PULLBOXES, AND EMERGENCY LIGHT
<br /> OBSTRUCTION. IT SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR TO 12. AS-BUILT DRAWINGS SHALL BE MAINTAINED AND REFLECT THE FOLLOWING: WET LOCATION RECEPTACLE.
<br /> INSTALL HIS WORK TO CONFORM TO THE STRUCTURE, PRESERVE HEADROOM
<br /> AND KEEP OPENINGS AND PASSAGEWAYS CLEAR. A. ANY DEVIATION FROM THE CIRCUIT NUMBERS ON WORKING DRAWINGS SHALL CI GFCI WATER PROOF WEATHER RESISTANT EXTRA DUTY.
<br /> BE INDICATED ON AS-BUILTS.
<br /> 9. WIRING AND CONNECTIONS OF EQUIPMENT BY OTHERS: FURNISH AND
<br /> INSTALL WIRING FOR POWER REQUIREMENT AS SHOWN ON DRAWINGS. B. OUTLETS THE ADDITION, DELETION OR RELOCATION OF OUAS SHOWN ON
<br /> COORDINATE WITH OTHER TRADES ON DETAILS OF INSTALLATION. THE WORKING DRAWINGS SHALL BE INDICATED ON TLETSILTS".
<br /> TERM "WIRING" AS USED HEREIN, INCLUDES FURNISHING AND INSTALLING 13. ALL CONDUIT OTHER THAN USED FOR ELECTRICAL WIRING SHALL HAVE #12
<br /> CONDUIT, WIRE, JUNCTION BOXES, DISCONNECTS, AND MAKING GALVANIZED PULL WIRE INSTALLED BY THE ELECTRICAL CONTRACTOR.
<br /> CONNECTIONS. CHECK UGH11NG CONSULTANT AND SPECIFICA11ONS FOR
<br /> EQUIPMENT TO BE INSTALLED BY OTHERS. ELECTRICAL DRAWINGS 14. ALL EXTERIOR RECEPTACLES SHALL BE WEATHER-PROOF TYPE. AND GFCI
<br /> INDICATE IN GENERAL THE INTENT AND SCOPE OF SYSTEMS. CONTRACTOR PROTECTION.
<br /> SHALL BE RESPONSIBLE FOR PROPER WIRING AND NECESSARY ELECTRICAL
<br /> ADJUSTMENTS TO EQUIPMENT TO CONFORM TO SPECIFIED REQUIREMENTS OF 15. ALL WORK SHALL BE DONE IN ACCORDANCE WITH LOCAL & STATE CODES.
<br /> THE EQUIPMENT. 16. THE ELECTRICAL CONTRACTOR SHALL VERIFY THE EXACT LOCATION, DEPTH AND »
<br /> (EXISTING) MS
<br /> 10. SHOP DRAWINGS: WITHIN FOURTEEN (14) DAYS AFTER RECEIPT OF ADEQUACY OF ALL SERVICES BEFORE STARTING AND SHALL NOTIFY THE GENERAL
<br /> CONTRACTOR IF SAID CONNECTION ARE NOT IN THE LOCATION SHOWN OR ARE NOT r----------------1
<br /> CONTRACT, SUBMIT TO ARCHITECT SEVEN (7) COMPLETE SETS OF DRAWINGS
<br /> FOR ALL ELECTRICAL EQUIPMENT AND DEVICES. DO NOT DELIVER THESE OF SUFFICIENT SIZE OR DEPTH TO MAKE THIS CONNECTION IN COMPLIANCE WITH 1 120/208V,30,4W
<br /> I
<br /> I I
<br /> ITEMS TO THE JOB SITE UNTIL SHOP DRAWINGS HAVE BEEN REVIEWED AND THIS PLAN.
<br /> APPROVED BY ARCHITECT AND ELECTRICAL ENGINEER. 17. THESE PLAN INDICATE APPROXIMATE DIMENSION ONLY FOR EQUIPMENT OR FIXTURE.
<br /> EXACT DIMENSIONS MUST BE OBTAINED FROM THE EQUIPMENT MANUFACTURER. I I
<br /> 11. OUTLET BOXES: OUTLET BOXES SHALL BE ONE PIECE PRESS STEEL BOC.
<br /> "4S" MINIMUM SIZE OR LARGER AS REQUIRED PER CODE. 18. THE CONDUIT & PIPING SHOWN ON PLANS ARE SCHEMATIC ONLY. INSTALL DUCT AND i M I
<br /> PIPING TO SUIT THE STRUCTURAL CONDITIONS. PROVIDE ALL NECESSARY
<br /> 12.CONDUIT SHALL BE STANDARD STEEL RIGID, IMC OR EMT (THIN WALL) OFFSETS AS REQUIRED. VERIFY WITH ARCHITECTURAL, STRUCTURAL, HVAC. ( I
<br /> ACCORDING TO CEC CODE AND LANDLORD REQUIREMENTS. FIRE PROTECTION AND PLUMBING DRAWINGS. I
<br /> CONDUIT SHALL BE CONCEALED IN FINISHED AREAS, EXCEPT AS 19. ELECTRICAL CONTRACTOR SHALL PROVIDE ALL ELECTRIC DEVICE, CONTROL VALVES i 200A
<br /> OTHERWISE APPROVED BY ARCHITECT. EMT CONNECTIONS SHALL BE AND ACCESS PANELS, ETC. TO ASSURE AN APPROVED ACCEPTABLE ELECTRICAL
<br /> COMPRESSION OR SET SCREW TYPE. LIQUIDTIGHT FLEXIBLE METAL SYSTEM. ( 3P I
<br /> CONDUIT SHALL BE USED FOR MOTOR CONNECTIONS, AND 20. SEAL ALL OPENINGS AROUND ELECTRIC CONDUITS AND PIPES (WIRES) PENETRATING 11
<br /> COMPLY WITH ARTICLE 350. THE FIRE RATED FLOOR & WALLS WITH APPROVED FIRE RETARDING MATERIALS. (� I
<br /> PVC CONDUIT SHAD_ BE USED ONLY FOR UNDERGROUND CONDUIT. 21. INSTALL EXPANSION JOINTS IN THE CONDUITS AND PIPINGS AND EXPANSION ( p I
<br /> FLEXIBLE METAL CONDUIT SHALL BE INSTALLED PER ARTICLE 348. LOOPS IN THE PIPING AS REQUIRED BY THE LOCAL ADMINISTRATIVE AUTHORITY. I
<br /> MC CABLE SHALL BE SUITABLE FOR INSTALLATION IN CONCEALED AREAS 22. ELECTRICAL CONTRACTOR SHALL COORDINATE HIS WORK CAREFULLY W/ THE I G dip
<br /> SUCH AS ABOVE CEILINGS AND INSIDE WALL CONSTRUC11ON AND PLUMBING, FIRE PROTECTION AND HVAC CONTRACTORS TO AVOID INTERFERENCES.
<br /> COMPLY WITH ARTICLE 330. MINIMUM CONDUIT SIZE SHALL BE 1/2". 23. AU_ CONDUITS & WIRES SUSPENDED IN BASEMENT OR CEILING SHALL BE INSTALLED
<br /> AS HIGH AS POSSIBLE. L___
<br /> 13.WIRE AND CABLE: ALL CONDUCTORS SHALL BE DELIVERED TO THE SITE IN 24. ALL 15 AND 20 AMPERE, 125 AND 250 VOLTS NONLOCKING RECEPTACLES
<br /> THEIR ORIGINAL UNBROKEN PACKAGES, PLAINLY MARKED OR TAGGED AS
<br /> FOLLOWS: SHALL BE LISTED WEATHER-RESISTANT TYPE IN A DAMP OR WET LOCATION EXISTING
<br /> 14. UNDERWRITERS' LABELS. (406. 8(a) &.(B). GROUND = -+I 2"C-4#3/0&1#6GROUND
<br /> SIZE, TYP. AND INSULATION OF WIRE. 25. ALL ELECTRICAL EQUIPMENT SHALL BE LISTED BY U.L OR LOCAL GOVERNMENT 1t1
<br /> NAME OF THE MANUFACTURING COMPANY AND THE TRADE NAME OF THE APPROVED THIRD PARTY TESTING FACILITY. PER SECTION 110.3 (b) D
<br /> WIRE. 26. NO PIPING,DUCTS OR EQUIPMENT FOREIGN TO ELECTRICAL EQUIPMENT SHALL BE
<br /> MONTH AND YEAR WHEN MANUFACTURED WHICH DATE SHALL NOT EXCEED PERMITTED TO BE LOCATED WITHIN THE DEDICATED SPACE ABOVE A (0 �/
<br /> TWO (2) YEARS PRIOR TO THE DATE OF DELIVERY TO THE SITE. THE ELECTRICAL EQUIPMENT.
<br /> 15.CONDUCTORS FOR SIZES #14 THRU #10 SHALL BE SOLID SOFT DRAWN 27• FUSES SHALL BE PROVIDED WITH REJECTION TYPE FUSE HOLDERS. Q
<br /> COPPER, 600 VOLT, TYPE THHN/THWN INSULATION EXCEPT AS 28. UNLESS LISTED OTHERWISE, THE AMPACITY OF 600 VOLTS OR LESS Z
<br /> HEREINAFTER SPECIFIED. CONDUCTORS SHALL BASE ON THE TERMINALS NOT EXCEED 60' C FOR CONDUCTOR Q
<br /> SIZE 12 THRUGH 1 AWG OR 75' C FOR CONDUCTOR SIZES OVER 1 AWG.
<br /> 16.CONDUCTORS FOR SIZES #8 AND LARGER SHALL BE STRANDED COPPER WITH < m M
<br /> 600 VOLT, TYPE THHN/THWN INSULATION. 29. APPLIANCES PROVIDED AND INSTALLED MEETS ENERGY STAR IF AN SINGLE LINE DIAGRAM
<br /> ENERGY STAR DESIGNATION IS APPLICABLE FOR THAT APPLIANCE AND O U rn
<br /> 17.MINIMUM WIRE SIZE SHALL BE #12 A.W.G. UNLESS SPECIFICALLY NOTED SUBJECT TO FIELD VERIFICATION. Q Q
<br /> AS #14. 30. WORKING SPACE: MINIMUM 3FT WORKING SPACE SHALL BE PROVIDED _� U
<br /> UTI TY NOTES: AND MAINTAINED FOR ALL ELECTRICAL PANELS AND EQUIPMENT. PER CEC 110.26. Z U
<br /> 31. SERVICE EQUIPMENT SHALL BE FIELD MARKED WITH THE MAXIMUM AVAUABLE FAULT 00
<br /> 1. ELECTRICAL CONTRACTOR MUST OBTAIN APPROVED CONSTRUCTION CURRENT, INCLUDING THE DATE THE FAULT CURRENT CALCULATION WAS PERFORMED, Q a
<br /> DRAWINGS FROM THE RESPECTIVE UTILITY COMPANIES AND INCLUDE PER C.E.C. ARTICLE 110.24
<br /> ALL MATERIAL AND WORK AS INDICATED THEREON IN THIS BID P TO P FAULT CURRENT CALCULATION M F_32. PROVIDE SEPARATE NEUTRALS FOR ALL SINGLE PHASE SYSTEMS AND ALL THE 7/28/2020
<br /> PRICE. IF UTILITY DRAWINGS ARE NOT AVAILABLE WHEN BIDS ARE MULTI-WIRE BRANCH CIRCUITS, WHERE HANDLE TIE IS NOT PERMITTED, REFER TO
<br /> SUBMITTED. SO INDICATE AND ADVISE ELECTRICAL ENGINEER C.E.C. ARTICLE(S) 215.4 AND 225.7 FOR ADDITIONAL REQUIREMTNTS. FROM TO LENGTH(FEET) Isc FEEDER C VALUE E�.-� f m Isc@Panel
<br /> ACCORDINGLY. F1 MS A 220 65000 #3/0 12844 208 9.27 0. 10 6500 �} LSSI ;
<br /> 33. PROVIDE IDENTIFICATION LABEL INDICATING FEEDER SOURCE AT ALL PANELBOARDS p`� v' � Date 2020 v
<br /> 2. ELECTRICAL CONTRACTOR SHALL VERIFY EXACT LOCATION OF AND SWITCHBOARDS, PER C.E.C. ARTICLE 408.4(8). `x`
<br /> UTILITY PANELS, CONDUITS AND XFMR WITH RESPECTIVE U11LITY 34. CONDUCTORS OF A MULTI-WIRE BRANCH CIRCUIT SHALL ORIGINATE FROM '
<br /> Scale
<br /> COMPANIES PRIOR TO START OF ANY SITE WORK.
<br /> THE SAME PANELI30ARD. THE BRANCH CIRCUIT SHALL BE PROVIDED IN",0
<br /> 3. ELECTRICAL CONTRACTOR SHALL SUBMIT THE MAIN SWITCHBOARD WITH A MEANS THAT WILL SIMULTANEOUSLY DISCONNECT ALL -- .�. f Drawn
<br /> Y. N.
<br /> SHOP DRAWING TO POWER COMPANY REPRESENTATIVE PRIOR TO
<br /> UNGROUNDED CONDUCTORS AT THE POINT WHERE THE BRANCH CIRCUIT r
<br /> ��T"���� �-r,"��'�\' �
<br /> START OF ANY WORK AND OBTAIN APPROVED DRAWINGS. ORIGINATES. (210.4,240.15(8)(1)). Job�} l� # F 2 0 - 7 91
<br /> 4. GENERAL CONTRACTOR SHALL SUBMIT SINGLE LINE DIAGRAM, 35. SWITCHBOARD AND PANEL BOARDS SHALL BE FIELD MARKED
<br /> SITE PLAN AND LOAD INFORMATION DRAWINGS TO UTILITY POWER TO WARN QUALIFIED PERSONS OF POTENTIAL ELECTRICSheet
<br /> N
<br /> COMPANY TO OBTAIN SERVEIC REPORT INDICATING THE AVAILABLE ARC FLUSH HAZARDS (110.16). LL
<br /> FAULT CURRENT AND SERVICE ROUTING. E=1
<br /> Of 5 Sheets
<br />
|