Laserfiche WebLink
PF Series 6d -Hz, 4 -inch (1 00 -mm) <br />Submersible Effluent Pumps <br />Applications <br />Our 4 -inch (100 -mm) Submersible Effluent Pumps are designed to <br />transport screened effluent (with low TSS counts) from septic tanks or <br />separate dosing tanks. All our pumps are constructed of lightweight, <br />corrosion -resistant stainless steel and engineered plastics; all are field - <br />serviceable and repairable with common tools; 60 -Hz PF Series models <br />are CSA certified to the U.S. and Canadian safety standards for effluent <br />pumps, meeting UL requirements, <br />Orenco's Effluent Pumps are used in a variety of applications, includ- <br />ing pressurized drainfields, packed bed filters, mounds, aerobic units, <br />effluent irrigation, effluent sewers, wetlands, lagoons, and more. These <br />pumps are designed to be used with a Biotube° pump vault or after a <br />secondary treatment system. <br />Franklin <br />Liquid End <br />Franklin <br />Super Stainless <br />Motor <br />ca- <br />usc <br />LR80980 <br />LR2053896 <br />Discharge Connection <br />Bypass Orifice <br />Suction Connection <br />Powered by <br />Franklin Electric <br />Features/Specifications <br />To specify this pump for your installation, require the following: <br />• Minimum 24-hour run -dry capability with no deterioration in pump life <br />or performance' <br />• Patented A -inch (3 -mm) bypass orifice to ensure flow recirculation <br />for motor cooling and to prevent air bind <br />• Liquid end repair kits available for better long-term cost of ownership <br />• TRI-SEALTM floating impeller design on 10, 15, 20, and 30 gpm <br />(0.6, 1.0, 1.3, and 1.9 Usec) models; floating stack design on 50 and <br />75 gpm (3.2 and 4.7 Usec) models <br />• Franklin Electric Super Stainless motor, rated for continuous use and <br />frequent cycling <br />• Type SCOW 600-V motor cable <br />Not applicable for 5 -hp (3.73 kW models <br />Standard Models <br />See specifications chart, pages 2-3, for a list of standard pumps. For <br />a complete list of available pumps, call Orenco. <br />Product Code Diagram <br />PF❑❑❑❑❑'❑ <br />Tord length, ft (m):' <br />Blank = 10 (3) 20 = 20 (6) <br />30 = 30 (9) 50 = 50 (15) <br />Check valve: <br />Blank = no internal check valve <br />CV = internal check valve' <br />Voltage, nameplate: <br />1 = 115' 200 = 200 <br />2 = 230 4 = 460 <br />Frequency: <br />1 = single-phase 60 Hz <br />3 = three-phase 60 Hz <br />Horsepower (kw): <br />03 = rh hp (0.25) 05 = Ys hp (0.37) <br />07 = - hp (0.56) 10 = 1 hp (0.75) <br />15 = 1 Ys hp (1.11) 20 = 2 hp (1.50) <br />30 = 3 hp (2.24) 50 = 5 hp (3.73) <br />Nominal flow, gpm (Usec): <br />10 = 10 (0.6) 15 = 15 (1.0) <br />20 = 20 (1.3) 30 = 30(1.9) <br />50 = 50 (3.2) 75 = 75(4.7) <br />Pump, PF Series <br />Yrhp (0.37k% only <br />Available for 10 gpm (0.6 Usec), 1/2 hp (0.37 kW) only <br />Note: 20 -ft cords are available only for single-phase pumps through 114 hp <br />Orenco Systems® Inc. , 814 Airway Ave., Sutherlin, OR 97479 USA • 800-348-9843 • 541-4594449 • www.orenco.com NTD-PU-PF-1 <br />Rev. 5.0, ® 03/17 <br />Page 1 of 5 <br />