|
A UASTAR NG Pr
<br />pool products in►
<br />VGB SERIES
<br />SUBMERGED, MULTIPLE AND SINGLE SUCTION OUTLET INSTRUCTIONS
<br />IMPORTANT SAFETY INSTRUCTIONS FOR
<br />10AVRxxx, 10AVxxx, SUN18xxx, SUNA18xxx, SUN 18HPHxxx, WAV24xxx, 24xxx,1216xxx, R1216xxx,
<br />914xxx, R914xxx, ABRxxx, ABxxx, 8AVxxx, LPBAVxxx, RFS9xxx, RFS12xxx, RWAV9xxx, RWAV12xxx,
<br />SUN9xxx, SUN12xxx, WAV9xxx, WAV12xxx, WAV18xxx, Al ORCFRxxx, 8FUWxxx
<br />(ON BACK PAGE:6HPxxx, 4HPxxx, 8HPxxx, RBHPxxx)
<br />(xxx = COLOR SUFFIX)
<br />MEETS OR EXCEEDS ASME/ANSI All 12.19.8b-2009 IASME
<br />ANTI-ENTRAPMENT/ANTI-VORTEX 1 /j91
<br />• • • • • ,AYla1a=8--
<br />�a.I
<br />zam
<br />IMPROPER INSTALLATION OR USE OF THIS PRODUCT MAY PRESENT A RISK OF HAIR OR BODY ENTRAPMENT AND
<br />DROWNING. Install this equipment in accordance with the instructions provided. Use only with the components and
<br />mounting hardware provided. FAILURE TO FOLLOW THESE INSTRUCTIONS AND/OR USE WITH COMPONENTS NOT
<br />PROVIDED BY AQUASTAR POOL PRODUCTS AND INTENDEDTO BE USED WITH THIS PRODUCT MAY RESULT IN IMPROPER
<br />POSITIONING OR FUNCTIONING OF SUCTION OUTLET AND MAY CAUSE SEVERE PERSONAL INJURY OR DEATH.
<br />SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
<br />If not a single, unblockable outlet, in the event of one suction • SPECIAL NOTES:
<br />outlet being completely blocked, the remaining suction outlets pool finish should never exceed top of frame.
<br />serving the system shall have a flow rating capable of the full
<br />flow of the pump(,) or the specific suction system. If in doubt • Taper pool finish down and away from top (or lower) of frame.
<br />about the ratinggor spa professional anaior ourrespective- and/or head loss curve of your system, consult
<br />a qualified poofTo of rate should nevar be installed lower than pool
<br />ysh.9
<br />equippment manufacturer(s). Also, double check with your local fin
<br />building/health authorities regarding single vs. multiple drain . Take special notice when retrofitting into an existing frame
<br />installations, etc. where ossible existing multiple layers of re -plastering have
<br />All sizes of connecting ppipe are acceptable, ending velocity created a concave situation, either chip or grind down old
<br />and GPM calculations. he larger, the betterPDO NOT exceed surface or install new frame at higher level. Use of bushing kit
<br />maximum flow rate(s) of cover or pipe(s) flow rate(s), whichever may also be required to achieve proper elevation.
<br />is less.
<br />• Replace cover and screws within 5 years.
<br />Pipe Size P/z" 2" 216" 3"
<br />\ Flow Rate in GPM I 45 80 110 160
<br />Q ALL MODELS LISTED BELOW = ANTI-ENTRAPMENT/ANTI-VORTEX AND FOR SINGLE OR MULTIPLE USE
<br />Rev 083111
<br />MAX •
<br />• •UTLET) MOUNTING •• • • ••
<br />Model
<br />WAV24xxx
<br />24xxx
<br />1216xxx
<br />914xxx
<br />SUN18HPHxxx
<br />10AVRxxx'.
<br />ABRxxx
<br />ABRxxx
<br />BAVxxx
<br />(and
<br />(and
<br />(min 6'pipe size)
<br />(and l OAVRDDSBM,,
<br />(and AaRSOxn,
<br />(with solid riser
<br />(and RF59xxx,
<br />R1216xxx)
<br />R914xxx)
<br />I OAVRDDxxx)(with
<br />A8R5BACmx,AeRDDSBxxx,
<br />ring)
<br />8511m, BSBACxxx,
<br />solid riser ring)
<br />ABRDDxm, RA814xx)
<br />(Sumpless)
<br />BSBVM)
<br />(min 2" pipe size)
<br />(with solid riser ring)
<br />(with vented riser
<br />(min 2" pipe size)
<br />ring)
<br />Floor
<br />1444 GPM
<br />1531 GPM
<br />460 GPM
<br />560 GPM
<br />1000 GPM
<br />.8 fps
<br />145 GPM
<br />140 GPM @
<br />88 GPM @ 2.0 fps
<br />@1.3 fps
<br />@IAfps
<br />@1.46 fps
<br />@2.1 fps
<br />@3.1 fps
<br />@2.9 fps
<br />2.8 fps
<br />Wall
<br />1444 GPM
<br />1531 GPM
<br />445 GPM
<br />300 GPM
<br />644 GPM
<br />96 GPMqr 2.8 fps
<br />84 GPM
<br />84 GPM @ 1.7
<br />70 GPM @ 1.6 fps
<br />@1.3 fps
<br />I @IAfps
<br />@1.4 fps
<br />@1.2 fps.
<br />@2.0 fps IQ
<br />@1.7 fps
<br />fps
<br />Rev 083111
<br />
|