COMPLIANCE INFO_2021 - Laserfiche WebLink

Home Browse Search

W.O.# NW1-2349677 Overfill Protection Testing Scope This procedure will provide a Need.,Root ATG calified technicians pro-tivra in safely teat rank event, Protection Reference Documents •Veedar-Root Ti Operators Manuel(576013310) • Veeder•Root TLS-3XX Setup Mai lY(576013.623) •Vaeder-Root TLS-450 Setup end Opwatlon Screen.Manuel(677013-940) •Veadar-Ract TLS-450PLUS/TL54 Operator's Manuel(677014-110) •Veedar-Root TL54 Ouick Shed(577014,034) •Veedar-Root Overfill Alarm Installation Guide(676013-539) Consoles TLS-450PLUS,TLS4c,TL84i,TLS-450 and TLS3XX Requirements TLS-460PLU5,TL54a,TLS41.TLS-460:Automatic Event:Device Task programmed to trigger on Tank Overfill and close a relay leading-Uge to the Ove 1111 alarm device. TLS-3XX:Output relay programmed to close a relay on.Tank Overfill alarm teaseling voltage to the Overfill elan, device. Testing procedure 1. Inspection a.Varity the levels in the tank to make aura there is product in the tank and that the tank is enabled. b.H the site is mart ntly receiving adelivery,welt until the delivery is complete. c.If the ankle performing a SLD lank teat,atop the teat. 2. Preparation a.Turn Alarm filtering off,as this will allow you to clear alarms quicker.Refer to TLS•3XX Setup menual (576013.623)or TLS4XX on-line help. b.Program Datil delay to 1 minute,this will allow the delivery to be completed quicker, 1.Note the customers original value,so you can.esces It after the teat. 24 Overfill PM len manta renrng Protech, c.PnM the Tank Inventory Report. d.Teat the relay assigned to the a#emal Ovarfll alarm(if present)to insure the Overfill alarm works. 1.If the Overrll alarm does not sound,repair the device before continuing testing, 3. Testing a.Tum off power to the cense,¢. h.Disconnect the probe from the field viring and remove it from the near. 1.g you ere lasting mare than one tank remove all the probes from their Asara. c.Lay the probe safely on the ground and reattach the field wiring. d.Position the water float at the bottom of the probe and the product float 25%up from the bottom of the probe. e.Power the-,sole back on. f. Simulate a delivery as follow.: 1.Move the float towards the top of the probe at seats of 1-2"per len aecands. 2.Continua moving the float to festal of the probe at a rate of 1.21 par tan seconds for the nod 50 second.,the probe is now in delivery mode. 3.Slid,the float at a moderate speed to the top of the probe.Note to not alarm the float against the head of the probe,this can damage the,,oat. g.Once the float reaches the overfill level the Overall alarm,including.stern.,Overfill alarm(if present),will sound. h.Silence the Overfill alarm on the TLS and asternal Ovelill el.rm(if present)by acknowledging it. ,. Move the float down to the bottom of the probe.The TLS will clear the Overfill alarm ante the delivery delay lime it,complete. j, Repeat 31-3,for the other probes. 4. Test Completion e.Print out the delivery report for all tanks tested. It.Power off the epnaola, c.Replacethe probe.back Into the tank;before mauling into riser,ensure that the 1losis are positioned at the bottom of the probe. d.Power on the console. e.If the console is running BIR enter a manual adjustment for the emeu,t of the delivery. f. If the site is not running BIR give the delivery report to the were manager so they can log the delivery as part of the overfill tasting.