CORRESPONDENCE_2017-2018 - Laserfiche WebLink

Home Browse Search

s 0 FIELDWORK HEALTH & SAFETY PLAN (HASP) FOR FIELD INVESTIGATIONS OF PETROLEUM DISTILLATE FUELS Drilling • The drill rig is not to be operated in inclement weather. • The driller is to verify that the rig is properly leveled and stabilized before raising the mast. • Personnel should be cleared from the sides and rear of the rig before the mast is raised. • The driller is not to drive the rig with the mast in the raised position. • The driller must check for overhead power lines before raising the mast. A minimum distance of 10 feet between mast and overhead lines (<50 kV) is required. Increased separation may be required for lines greater than 50 kV. • Personnel should stand clear before rig startup. - 6 - Revision: 7 — June 2013 Down Hole Surveys/Cameras safe work procedures, PPE, training Batteries -jumping, servicing safe work procedures, training, PPE Tire Changing safe work procedures, training, PPE Maintenance Engine Maintenance safe work procedures, training, PPE, lockout Refueling safe work procedures, training, PPE Servicing Pressure Systems safe work procedures, training, PPE, lockout Night Work(visibility) proper lighting, safe work practices Misc. - Chemical Hazards PPE, training, safe work practices These Noise engineering, administration, PPE types of hazards Dust engineering, administration, PPE may be Working at Height PPE, training, safe work procedures found in Equipment Fires training, safe work procedures, safety inspections some or all Welding / Cutting PPE, training, safe work procedures of the Wire Roe PPE, training, safe work procedures operations Housekeeping safe work procedures, safety inspections listed above. Manual Handling training, safe work procedures Sampling Traffic and forklift traffic to and from laboratory Coordinate work closely between all site personnel. All lift trucks must have operating backup with samples. alarm. Strain or crushing injury from moving heavy Use proper lifting and unloading techniques. Use proper equipment and caution when objects. unloading or moving heavy objects. Wear leather gloves when moving heavy objects. Failing objects and overhead hazards. Wear hardhat at all times. Be aware of potential overhead equipment. Slip/trip/fall on uneven surfaces or debris in the Use caution and be aware of your surroundings. Maintain a clean work area. Wear steel toe work area. work boots. Contusions, lacerations or strain from use of Use the right tools for the job. Use tools that are in good working order. Wear leather gloves hand tools. when using hand tools. Projectiles, eye irritation from blowing dust and Wear proper PPE face during sampling or chemical hazards Exposure to chemical contaminants Wear specified PPE. Follow site control procedures. Follow decontamination and hygiene procedures. Traffic hazard during mobilization of and Coordinate work closely between CDLP and all other on-site personnel. All heavy equipment operation of equipment must have operating backup alarm. All personnel must watch for traffic between buildings. Strain or crushing injury from unloading or Use proper lifting and unloading techniques. Use proper equipment and caution when moving heavy objects. unloading or moving heavy objects. Non essential personnel to stay clear of areas where hea objects are beingmoved. Wear leather loves when movingheavyobjects. Decontamin ation of Slip/trip/fall surfaces or debris in the Use caution and be aware of your surroundings. Maintain a clean work area. Wear steel toe surfaces work area. . Nail stiuneven down And pipe work boots and hard hats. hanging Contusions, lacerations or strain from use of Use the right tools for the job. Use tools that are in good working order. Wear leather gloves hand tools. when using hand tools. Noise near operating machinery Use hearing protection per "Arms Length Rule." Eye irritation from dust during cleaning Wear safety glasses at all times during cleaning of petroleum and oils. Full face respirator operation required when cleaning areas containing metal dusts. Fall hazards if climbing on roll -offs Avoid climbing on roll -offs. Repetitive motion injuries Evaluate work station. Design work station to fit the individual. Vary work when possible. Take breaks. Utilize proper keyboards. Use phone headsets. Strain or crushing injury from moving objects. Use proper lifting and unloading techniques. Use proper equipment and caution when unloading or moving heavy objects. Wear leather gloves when moving heavy or rough Office Work objects. Falling objects and overhead hazards. Do not store heavy objects over head height. Utilize proper equipment such as ladders to reach high objects. Clear personnel from surrounding area during overhead work. Slip/trip/fall on uneven surfaces or debris in the Use caution and be aware of your surroundings. Maintain a clean work area. Keep file work area. cabinet drawers closed. Drilling • The drill rig is not to be operated in inclement weather. • The driller is to verify that the rig is properly leveled and stabilized before raising the mast. • Personnel should be cleared from the sides and rear of the rig before the mast is raised. • The driller is not to drive the rig with the mast in the raised position. • The driller must check for overhead power lines before raising the mast. A minimum distance of 10 feet between mast and overhead lines (<50 kV) is required. Increased separation may be required for lines greater than 50 kV. • Personnel should stand clear before rig startup. - 6 - Revision: 7 — June 2013