|
260500 ELECTRICAL WORK FOR COMMON RESULTS: D. WEATHERPROOF BOXES SHALL BE APPLETON FD SERIES AND FITTED WITH GASKETED CAST 6. INSTALL NO CONDUCTORS UNTIL WORK WHICH MIGHT CAUSE DAMAGE TO SUCH CONDUCTORS 262726.02, DEVICE PLATES:
<br /> 1. ELECTRICAL INSTALLATION SHALL COMPLY WITH TITLE 24, CALIFORNIA COVERS. OR THE CONDUIT HAS BEEN COMPLETED,
<br /> CODE OF REGULATIONS, INCLUDING THE FOLLOWING: E1. ALL DEVICE PLATES FOR INDOOR USE SHALL BE NYLON.
<br /> . VOICE/DATA OUTLET BOXES SHALL BE 4_11116"50.x2_118"DEEP MINIMUM, FITTED WITH PLASTER 7. KEEP ALL CONDUITS AT LEAST SIX INCHES AWAY FROM THE COVERING ON HOT WATER OR STEAM
<br /> TITLE 24, CCR, PART 2, 2019 CBC RINGS. PIPES.
<br /> TITLE 24, CCR, PART 3, 2019 CEC 2. ALL DEVICE BOXES WHICH ARE INSTALLED IN FIRE RATED WALL ASSEMBLY AND IS PROVIDED WITH
<br /> A FIRE-STOPPING PUTTY PAD SHALL HAVE A BRUSHED STAINLESS STEEL COVERPLATE IN ACCORDANCE
<br /> TITLE 24, CCR, PART 4, 2019 CMC
<br /> TITLE 24, CCR, PART 9, 2019 CFC F. BOXES FOR SPECIAL EQUIPMENT SHALL BE SUITABLE FOR THE PARTICULAR EQUIPMENT. 8. CAP RACEWAY ENDS DURING CONSTRUCTION. CLEAN OR REPLACE CONDUITS IN WHICH WATER WITH THE REQUIREMENTS OF THE PUTTY PAD.
<br /> OR FOREIGN MATTER HAVE ACCUMULATED, TO THE SATISFACTION OF THE ARCHITECT.
<br /> TITLE 24, CCR, PART 6, 2019 CALIFORNIA ENERGY CODE G. BOXES SHALL BE LOCATED AND PLACED ACCORDING TO ARCHITECTURAL AND STRUCTURAL 3. DEVICE COVERS FOR SURFACE MOUNTED BOXES SHALL BE 112" RAISED STEEL PLATES.
<br /> ALL APPLICABLE LOCAL CODES
<br /> TITLE 24, CCR, PART 11, 2019 CALIFORNIA GREEN BUILDING STANDARDS CODE REQUIREMENTS. 9. CONDUITS SHALL BE SUPPORTED WITH STRAPS, WITH GALVANIZED MALLEABLE SPLIT RING AND
<br /> ROD FOR INDIVIDUAL RUNS OR WITH KINDORF OR UNISTRUT CHANNEL SUPPORTS FOR MULTIPLE RUNS, 4. DEVICE COVERS FOR DEVICES LOCATED IN DAMP LOCATIONS SHALL COMPLY WITH CEC 406.9(A).
<br /> 2. ELECTRICAL CONTRACTOR SHALL VERIFY POWER, TELEPHONE AND CABLE TV SERVICES AT SITE PRIOR
<br /> 260550. WIRING METHODS: LINE„VOLTAGE SYSTEMS (120V AND ABOVE): DISTANCE BETWEEN SUPPORTS SHALL NOT EXCEED 10 FEET. CONDUITS SHALL BE SUPPORTED
<br /> 9
<br /> DEVICE COVERS FOR DEVICES LOCATED IN WET LOCATIONS SHALL COMPLY WITH CEC 406. (8).
<br /> TO BIDDING. SERVICES TO CONFORM TO UTILITY COMPANY REQUIREMENTS. ELECTRICAL CONTRACTOR 1. ALL WIRING SHALL BE INSTALLED IN CONDUITS. CONDUITS SHALL BE RUN CONCEALED IN WALLS INDEPENDENTLY OF ONE ANOTHER. 5. wnn
<br /> SHALL ARRANGE FOR SERVICE INSTALLATIONS PER UTILITY COMPANY REQUIREMENTS AND PAY ALL AND CEILINGS WHERE FEASIBLE,ALL CONDUITS INSTALLED SURFACE ON WALL SHALL BE PAINTED TO 10. CONDUITS CONNECTED TO BOXES AND CABINETS SHALL BE FITTED WITH TWO LOCKNUTS AND ` ' ' ' `
<br /> CUSTOMER CHARGED SERVICE COSTS. COORDINATE WITH OWNER AND UTILITY COMPANY FOR SERVICE MATCH WALL FINISH. MOUNT EXTERIOR CONDUITS ON WALL ON GALVANIZED UNISTRUTS.ALL SURFACE INSULATED BUSHING, OA"A"SERIES. 262729. DISCONNECT SWITCHES:
<br /> INSTALLATION. CONDUIT INSTALLATION/RUNS SHALL BE APPROVED BY THE ARCHITECT PRIOR TO INSTALLATION.
<br /> 11. CONDUITS NOT CONNECTED WITH LOCKNUTS AND BUSHINGS SHALL BE FITTED WITH GROUNDING INDICATED ON THE DRAWINGS, OR AS REQUIRED BY CODE. SWITCHES AND FUSES SHALL BE AS REQUIRED
<br /> 3. 1. UNITS SHALL BE HEAVY DUTY FUSED DISCONNECT SWITCHES, TWO OR THREE POLE TYPE, WHERE ARCHITECTS
<br /> CONTRACTOR SHALL PROCURE AND PAY FOR ALL PERMITS, LICENSES, ETC. REQUIRED TO CARRYON 2. ALL CONDUITS RUN WITHIN INTERIOR FINISHED SPACES SUCH AS OFFICES, BREAKROOM, BUSHINGOZ"BL"SERIESU. L. . BY THE LOADS SERVING.
<br /> AND COMPLETE THE WORK. RESTROOM ETC. SHALL BE RUN CONCEALED, , , APPROVED AND BANDED
<br /> 12. CONDUIT STRAPS FOR INDIVIDUAL RUNS SHALL BE SECURED BY TOGGLE BOLTS ON HOLLOW 2. DISCONNECTS FOR FRACTIONAL HORSE POWER MOTORS SHALL BE MOTOR-RATED TOGGLE TYPE 5757 Pacific 4. PROVIDE ALL LABOR, MATERIALS,TOOLS, PLANT EQUIPMENT, TRANSPORTATION AND PERFORM ALL 3. ALL CONDUITS RUN IN DEDICATED ELECTRICAL AND MECHANICAL ROOMS SHALL BE RUN MASONRY, EXPANSION ANCHORS ON SOLID CONCRETE OR MASONRY, MACHINE SCREWS OR BOLTS ON fic Avenue
<br /> OPERATIONS NECESSARY FOR ANY REASONABLE INCIDENTAL TO PROPER EXECUTION AND COMPLETION EXPOSED. DISCONNECTS, Suite 226
<br /> OF ALL"ELECTRICAL WORK"WHETHER SPECIFICALLY MENTIONED OR NOT;ALL A5 INDICATED, SPECIFIED METAL SURFACES AND WOOD SCREWS ON WOOD CONSTRUCTION. THE USE OF NAILS TO ANCHOR
<br /> STRAPS PE WOOD CONSTRUCTION ISP AL Al IZE STRAPS SHALL A TWO HOLE MALLEABLE IRON OR 3. DISCONNECTS FOR SINGLE PHASE MOTORS SHALL BE SINGLE PHASE AND NOT THREE PHASE, Stockton, CA 96207
<br /> HEREIN,AND/OR IMPLIED THEREBY TO CARRY OUT THE APPARENT INTENT THEREOF. 4. MINIMUM CONDUIT SIZE SHALL BE 1I2"ABOVE GRADE AND 314" UNDERGROUND. SNAP-TYPE STEEL WITH RIBBED BACK, GALVANIZED OR CADMIUM PLATED. THE USE
<br /> 5. ALL MATERIALS SHALL BE NEW AND LISTED WITH THE UNDERWRITERS' LABORATORIES, INC., SHALL 5. MINIMUM ACCEPTABLE CONDUITS ARE: 4. LOCATE DISCONNECTS IN ACCORDANCE WITH CEC 430.102. ENSURE ALL CODE-REQUIRED
<br /> MEET THEIR REQUIREMENTS AND SHALL BEAR THEIR LABEL WHEREVER STANDARDS HAVE BEEN 13. PLACEMENT OF ALL BOXES SHALL BE GOVERNED BY APPLICABLE ARCHITECTURAL AND CLEARANCES. 2000 L Street
<br /> STRUCTURAL REQUIREMENTS. Suite 126
<br /> ESTABLISHED AND LABEL SERVICE IS REGULARLY FURNISHED BY THAT AGENCY, A. GALVANIZED RIGID STEEL-FOR USE ON:
<br /> 6. ELECTRICAL DRAWINGS ARE ESSENTIALLY DIAGRAMMATIC AND ALTHOUGH THE SIZE AND LOCATIONS
<br /> (1) EXTERIOR WALL SURFACES, 14. CONDUIT FITTINGS: EXCEPT WHERE OTHERWISE NOTED, CONDUIT FITTINGS SHALL BE APPLETON 265100. LIGHTING: Sacramento, CA 95811
<br /> OR APPROVED EQUAL. UNILETS SHALL BE MALLEABLE IRON AND FITTED WITH COVERS AND GASKETS.
<br /> OF EQUIPMENT ARE SHOWN TO SCALE WHEREVER POSSIBLE, CONTRACTOR SHALL MAKE USE OF ALL DATA B. GALVANIZED STEEL EMT FOR USE: 1. ALL LUMINARIES SHALL BE CERTIFIED BY THE MANUFACTURER TO THE CALIFORNIA ENERGY
<br /> IN ALL CONTRACT DOCUMENTS AND VERIFY THIS INFORMATION AT THE SITE. CONTRACTOR SHALL BE (1) CONCEALED IN INDOOR FINISHED SPACES. 15. TELEPHONE AND SIGNAL CONDUIT BENDS WHERE REQUIRED SHALL HAVE A RADIUS OF TEN TIMES COMMISSION: T 209.944.9110
<br /> RESPONSIBLE FOR LAYING OUT AND INSTALLING HIS WORK TO AVOID INTERFERENCE WITH OTHER TRADES. (2) EXPOSED INSIDE ELECTRICAL&MECHANICAL ROOMS. THE CONDUIT TRADE SIZE. F 209.944.5711
<br /> 7. WORK SHOWN ON THE DRAWINGS TO BE INSTALLED UNDERGROUND SHALL BE INSTALLED AT LEAST 24" C. LIQUID TIGHT STEEL FLEX: ALL LUMINARIES SPECIFIED ON THIS PROJECT SHALL BE AS NOTED IN THE"LIGHT FIXTURE 1NWW.wmbarchitects.com
<br /> BELOW GRADE UNLESS OTHERWISE NOTED. BACKFILL IN 6"THICK, PROPERLY MOISTENED LAYERS, 16. PROVIDE PULL TAPE IN ALL EMPTY CONDUITS. SCHEDULE"ON THESE PLANS. NO SUBSTITUTES ARE PERMITTED WITHOUT WRITTEN APPROVAL OF THE
<br /> (1) FOR FINAL CONNECTION TO OUTDOOR EQUIPMENT. LENGTH SHALL NOT EXCEED 36 . ENGINEER.
<br /> SOLIDLY PACKED AND IRON TAMPED TO A DENSITY NOT LESS THAN THAT OF ADJACENT, UNDISTURBED
<br /> EARTH. RESTORE SURFACES, ROADWAYS, WALKS, CURBS, WALLS AND EXISTING UNDERGROUND D. FLEXIBLE STEEL CONDUIT: 260800. TESTING: ALL INTERIOR LUMINARIES SHALL BE PROVIDES WITH 0-10V DIMMING LED DRIVERS.
<br /> INSTALLATIONS TO ORIGINAL CONDITION IN AN ACCEPTABLE MANNER. (1) FOR INDOOR FINAL CONNECTION TO RECESSED LIGHT FIXTURES. LENGTH SHALL NOT EXCEED 72". 1. THE ENTIRE ELECTRICAL INSTALLATION SHALL BE FREE FROM SHORT CIRCUITS AND IMPROPER
<br /> 8. ALL ELECTRICAL EQUIPMENT EXPOSED TO THE WEATHER SHALL BE LISTED FOR EXTERIOR USE. (2) FOR INDOOR FINAL CONNECTION TO HVAC EQUIPMENT. LENGTH SHALL NOT EXCEED 36". GROUNDS. TEST ALL WIRING AND CONNECTIONS FOR CONTINUITY AND GROUNDS BEFORE ANY FIXTURES ALL EXTERIOR LUMINARIES SHALL BE PROVIDED WITH 0-10V DIMMING LED DRIVERS WITH
<br /> E. "PVC" SCHEDULE 40:
<br /> OR EQUIPMENT ARE CONNECTED AND WHERE SUCH TESTS INDICATE FAULTY INSULATION OR OTHER INTEGRAL MOTION SENSORS WHERE SO NOTED.9. ALL U.L. LISTED EQUIPMENT SHALL BE INSTALLED AS PER THEIR LISTING OR LABELING. (1) FOR CONDUITS RUN UNDERGROUND AND FOR UNDER BUILDING SLAB. DEFECTS, THEY SHALL BE LOCATED, REPAIRED AND RETESTED AT THE CONTRACTOR'S EXPENSE.PROVIDE ALL INSTRUMENTS TO MAKE SUCH TESTS.
<br /> (2) CONDUIT STUBUPS THROUGH THE FLOOR OR GRADE SHALL BE IN PVC WRAPPED RIGID STEEL
<br /> 10. IN LOCATIONS WHERE ELECTRICAL EQUIPMENT WOULD BE EXPOSED TO PHYSICAL DAMAGE, CONDUIT. PVC WRAPPING SHALL EXTEND 6"ABOVE FINISHED FLOOR OR GRADE.
<br /> ENCLOSURES OR GUARDS SHALL BE SO ARRANGED AND OF SUCH STRENGTH AS TO PREVENT SUCH (3) NOT PERMITTED FOR WIRING ABOVE FINISHED FLOOR INSIDE BUILDINGS 2, DEMONSTRATE TO THE OWNER AND THE ARCHITECT,THAT THE ENTIRE INSTALLATION IS
<br /> DAMAGE. COMPLETE, IN PROPER OPERATING CONDITION AND THAT THE CONTRACT HAS BEEN PROPERLY AND
<br /> F. ALUMINUM CONDUITS, IMC CONDUITS OR ALUMINUM FITTINGS ARE NOT APPROVED FOR USE ON FULLY EXECUTED.
<br /> 11. CONFLICTS BETWEEN SPECIFICATIONS AND PLANS: THIS PROJECT.
<br /> 260800.01. CERTIFICATE OF COMPLETION:
<br /> a. ANY CONFLICT BETWEEN ELECTRICAL SPECIFICATIONS AND ELECTRICAL PLANS; OR BETWEEN G. ALL CONDUIT FITTINGS SHALL BE MALLEABLE IRON/STEEL. . ACCEPTANCE OF THE CONTRACT FOR THIS WORK INCLUDES THIS GUARANTEE: THE CONTRACTOR
<br /> ELECTRICAL PLANS AND PLANS OF ANOTHER DISCIPLINE SHALL BE BROUGHT TO THE ATTENTION OF THE 1
<br /> . GUARANTEES THAT HE HAS PERFORMED THE WORK IN ACCORDANCE WITH THE CONTRACT DOCUMENTS.
<br /> ENGINEER AND A RESOLUTION RECEIVED PRIOR TO PROCUREMENT OR INSTALLATION OF THE ITEM IN H. COUPLING: CONTRACTOR AGREES TO REPLACE OR REPAIR, AS NEW ANY DEFECTIVE WORK, MATERIALS, OR PART
<br /> QUESTION. (1) EMT COUPLING- -APPLETPLETONON
<br /> N TW-CC-CS SERIES WHICH MAY APPEAR WITHIN ONE YEARS (1) OF FINAL ACCEPTANCE, IF, IN THE OPINION OF THE
<br /> (2) EMT CONNECTOR-CONNECTOR
<br /> ON TW CSI SERIES ARCHITECT OR THE OWNER, THE DEFECT IS DUE TO WORKMANSHIP OR MATERIAL.
<br /> b. IF THE CONTRACTOR PROCEEDS WITH THE WORK WITHOUT RECEIVING ANY RESOLUTION TO THE (3) FLEX CONDUIT CONNECTOR-T&B TITE BITE", INSULATED
<br /> CONFLICT HE/SHE DOES SO AT HIS/HER OWN RISK AND SHALL RECTIFY THE WORK TO THE SATISFACTION (4) LIQUID TIGHT FLEX CONDUIT CONNECTOR-APPLETON"STB"SERIES UP TO 2","ST'SERIES OVER 2". Michael's Pizza
<br /> OF THE ENGINEER AT NO ADDITIONAL COST TO THE OWNER OR ENGINEER. 260800.02. WARRANTIES GUARANTEES, CERTIFICATES, ETC.: Remodel
<br /> I. RIGID STEEL CONDUIT CONNECTED TO BOXES AND CABINETS SHALL BE FITTED WITH TWO 1. WARRANTIES, GUARANTEES, CERTIFICATES, ETC.THAT ARE FURNISHED AND AVAILABLE FOR 2300 W Alpine Ave
<br /> 260500.02. SUBMITTALS: LOCKNUTS AND INSULATING BUSHING, OA"A"SERIES. PROVIDE GROUNDING BUSHING OZ"BL"SERIES EQUIPMENT AND MATERIALS FURNISHED AND INSTALLED UNDER THIS SECTION SHALL BE PROPERLY P
<br /> WHERE LOCKNUTS AND BUSHING IS NOT USED. CONDUITS CONNECTED TO BOXES EXPOSED TO Stockton, CA 95204
<br /> WEATHER/MOISTURE SHALL BE FITTED WITH WATERTIGHT SEALING HUBS OF STEEL OR MALLEABLE FILLED OUT AS OF DATE OF ACCEPTANCE OF THE WORK BY THE OWNER AND SHALL BE DELIVERED TO
<br /> 1. PROVIDE THE FOLLOWING SUBMITTALS FOR REVIEW AND APPROVAL. EACH SHALL BE SUBMITTED IRON WITH SEALING RING AND INSULATED THREAT, T&B 370 SERIES. THE ARCHTITECT.
<br /> SEPARATELY TO AVOID DELAYS IN THE REVIEW OF ONE SUBMITTAL IN HOLDING UP REVIEW OF THE
<br /> REMAINDER. J. TYPE NM AND NMC CABLES SHALL NOT BE USED ON THIS PROJECT. 260943. INTERIOR LIGHTING CONTROL SYSTEM:
<br /> a. SERVICE SWITCHBOARD
<br /> d. LIGHTING CONTROL PANEL.
<br /> K. THE PROJECT DRAWINGS ARE LAID OUT USING SOLID CONDUITS AND CABLES PULLED THROUGH 1. PROVIDE A COMPLETE AND FULLY OPERATIONAL INTERIOR LIGHTING CONTROL SYSTEM FOR e. LIGHTING CONTROLS SUCH CONDUITS. MC CABLES MAY BE UTILIZED AS DESCRIBED BELOW,WITH RESTRICTIONS NOTED, INTERIOR LIGHTING AS SPECIFIED HEREIN AND SHOWN ON THE DRAWINGS.
<br /> b• PANEL BOARDS
<br /> (1) PRIOR APPROVAL OF OWNER/ARCHITECT OR ENGINEER REQUIRED. 2. THE COMPLETE SYSTEM, INCLUDING ALL DEVICES SHALL BE IN COMPLIANCE WITH THE 2016
<br /> f. BASIC ELECTRICAL MATERIALS
<br /> c. LIGHT FIXTURES (2) MC CABLES SHALL BE AS MANUFACTURED BY SOUTHWIRE TYPE EZ-MC DURACLAD TYPE WITH LIGHT CALIFORNIA ENERGY CODE. GENERAL NOTES
<br /> WEIGHT STEEL ARMOR AND INSULATED GREEN GROUNDING CONDUCTORS OR APPROVED EQUAL.. 3. THE COMPLETE SYSTEM SHALL BE AS MANUFACTURED BY NLIGHT, WATTSTQPPER, OR
<br /> 260500.03. WORKING CLEARANCES FOR ELECTRICAL SWITCHGEAR' GREENGATE CONSISTING OF:
<br /> 1. PROVIDE WORKING SPACES FOR ELECTRICAL PANELS AND SWITCHGEAR TO COMPLY WITH CEC (3) SHALL BE USED FOR BRANCH CIRCUITS ONLY AS NOTED BELOW.
<br /> 110.26. (a) CANNOT BE USED ANYWHERE EXPOSED. A. LUMINARIES WITH 0-10V DIMMING LED DRIVERS.
<br /> 2. ELECTRICAL CONTRACTOR SHALL COORDINATE WITH ALL TRADES INVOLVED TO ENSURE THE B. WALL DIMMER SWITCHES THAT COMMUNICATE THROUGH ROOM CONTROLLERS.
<br /> CLEARANCES REQUIRED BY ITEM 1 ABOVE ARE PROVIDED. (b) LIGHTING:VERTICAL DROPS IN WALL FOR LIGHT SWITCHES FORM JBOX IN CEILING. HORIZONTAL_
<br /> RUNS IN CEILING SHALL BE IN SOLID STEEL CONDUITS. C OCCUPANCY SENSORS THAT COMMUNICATE THROUGH ROOM CONTROLLERS.
<br /> 260526. GROUNDING:
<br /> (c) POWER RECEPTACLES: D WHERE LIGHT FIXTURES FALL UNDER THE PRIMARY AND SECONDARY DAYLIT ZONES AS DEFINED
<br /> 1. GROUND AND BOND ALL EQUIPMENT AS REQUIRED BY GOVERNING CODES AND SPECIFICALLY BY SECTION 130.1(d) AND THE TOTAL INSTALLED GENERAL LIGHTING POWER IN THE PRIMARY DAYLIT ZONE
<br /> INCLUDING SWITCHBOARD, PANELBOARDS, MOTOR CASES, METAL PIPING SYSTEMS, STRUCTURAL STEEL, (A) FOR UNDERGROUND HOMERUNS: SOLID CONDUIT VERTICAL RISER IN WALL FROM UNDERGROUND IS NOT LESS THAN 120W(EXCEPTION#1 TO SECTION 130.1(d)2) SUCH LIGHT FIXTURES SHALL BE PROVIDED
<br /> ETC.
<br /> CONDUIT TO FIRST RECEPTACLE JBOX. THEN HORIZONTAL RUNS WITHIN WALLS TO OTHER WITH AUTOMATIC DAYLIGHITNG CONTROLS IN ACCORDANCE WITH SECTION 130.1(d)(2)(D).
<br /> RECEPTACLE BOXES IN MC CABLE.
<br /> 2. PROVIDE GROUND WIRES IN ALL FEEDERS AND BRANCH CIRCUITS, SIZE PER CEC TABLE 250.122 (B) FOR OVERHEAD HOMERUNS: VERTICAL DROPS FROM JBOX IN CEILING THEN HORIZONTAL RUNS E. PROVIDE A DEMAND RESPONSIVE CONTROLS FOR THE INTERIOR LIGHTING SYSTEM PER CEC
<br /> WITHIN WALLS TO OTHER RECEPTACLES. HORIZONTAL RUNS IN CEILING SHALL BE IN SOLID STEEL SECTION 130.5(e). PROVIDE A GATEWAY DEVICE TO ACHIEVE THIS. SET UP DEVICE SUCH THAT WHEN IT
<br /> 3. ALL GROUND WIRES SHALL BE INSULATED GROUND WIRES. CONDUITS. RECEIVES AN OPEN AUTOMATIC DEMAND RESPONSE (ADR)2.0 SIGNAL IT TRANSMITS THE ADR SIGNAL TO
<br /> EACH OTHER AND TO THE ROOM LIGHTING CONTROLLERS. THE ROOM CONTROLLERS SHALL DIM THE
<br /> (d) NO OTHER USE IS PERMITTED WITHOUT SPECIFIC WRITTEN APPROVAL OF THE ARCHITECT OR LIGHT FIXTURES TO REDUCE ENERGY CONSUMPTION BY AT LEAST 15%, BUT NOT MORE THAN 50%WHEN
<br /> 260529. INSTALLATION OF SUPPORT SYSTEMS ENGINEER. THE SIGNAL IS RECEIVED-
<br /> 1.
<br /> ECEIVED_1. RACEWAYS, CABLE ASSEMBLIES, BOXES, CABINETS,AND FITTINGS SHALL BE SECURELY FASTENED (4) ALL FITTINGS AND TERMINATIONS FOR THE MC CABLING SYSTEM SHALL BE METAL AND SUITABLE F. TIME BASED GATEWAY DEVICE THAT PROVIDES TIME-BASED SIGNAL TO ROOM CONTROLLERS FOR
<br /> IN PLACE PER CEC ARTICLE 300.11. SUPPORT WIRES THAT DO NOT PROVIDE SECURE SUPPORT SHALL NOT AND LISTED FOR SUCH USE. ALL SPACES THAT CONTROLLED BY MOTION SENSORS TO AUTOMATICALLY SHUT-OFF LIGHTS AT THE END
<br /> BE PERMITTED AS THE SOLE SUPPORT. SUPPORT WIRES AND ASSOCIATED FITTINGS THAT PROVIDE OF DAY
<br /> SECURE SUPPORT AND THAT ARE INSTALLED IN ADDITION TO THE CEILING GRID SUPPORT WIRES SHALL BE {5) ALL SUPPORTS,ATTACHMENTS SPACING SHALL BE PER CEC 330.30.
<br /> PERMITTED AS THE SOLE SUPPORT. WHERE INDEPENDENT SUPPORT WIRE ARE USED,THEY SHALL BE 4. ALL SYSTEM COMPONENTS SHALL BE UL LISTED.ALL SYSTEM CONTROL_COMPONENTS SHALL BE
<br /> SECURED AT BOTH ENDS. CABLES AND RACEWAYS SHALL NOT BE SUPPORTED BY CEILING GRIDS. (6) FOR MULTI-WIRE BRANCH CIRCUITS SUCH CABLES SHALL HAVE MULTIPLE NEUTRALS, ONE FOR APPROVED BY THE CALIFORNIA ENERGY COMMISSION.
<br /> EACH CIRCUIT.
<br /> 2. FURNISH ALL NECESSARY FOUNDATIONS, SUPPORTS, BACKING, ETC., FOR ALL ELECTRICAL 5. ALL EQUIPMENT AND ITEMS OF CONTROL SHALL BE INSTALLED AND WIRED IN ACCORDANCE WITH
<br /> ENCLOSURES, CONDUITS AND EQUIPMENT. 6. CONDUCTORS SHALL BE COPPER CONDUCTORS TYPE THHN/THWN UNLESS OTHERWISE NOTED MANUFACTURER'S REQUIREMENTS. PUBLISH HISTORY:
<br /> OR REQUIRED BY CODE.
<br /> LEVEL AUTOMATIC"ONVAUTOMATIC"OFF"AS SHOWN,
<br /> 3. ATTACH ALL BOXES, CABINETS, ETC. TO WOOD WITH WOOD OR LAG SCREWSTO METAL WITH DATE REVISION
<br /> 6. PROVIDE WALL OCCUPANCY SENSOR LIGHT SWITCHES WHERE SO SHOWN ON PLANS. SUCH Np.
<br /> -a 7. ALL DEVICES, CONDUITS, RACEWAYS AND CABLES SHOWN ARE NEW TO BE PROVIDED UNLESS OCCUPANCY SENSOR SWITCHES SHALL BE SINGLE MACHINE SCREWS OR BOLTS AND TO CONCRETE WITH EXPANSION ANCHORS AND MACHINE SCREWS OR OTHERWISE NOTED.
<br /> c BOLTS. ON PLANS. SENSORS SHALL COMPLY WITH SECTION 110.9 OF THE ENERGY CODE. 08.19.20 PERMIT SET
<br /> 2. RIGID STEEL CONDUIT SHALL BE SUPPORTED AT INTERVALS NOT GREATER THAN 10 FT, ELECTRICAL 8. FLASH AND COUNTERFLASH ALL ITEMS PASSING THROUGH THE ROOF. 7. THE SYSTEM SHALL AUTOMATICALLY SWITCH OFF ALL LIGHTS WHEN CONTROLLED SPACE
<br /> E METALLIC TUBING AT INTERVALS NOT GREATER THAN 5 FT. BECOMES UNOCCUPIED AND SWITCH ON LIGHTS WHEN THE SPACE IS RE-OCCUPIED. ALL SENSORS SHALL
<br /> 9. THE OWNER RESERVES THE RIGHT TO RELOCATE ALL LIGHTING, OUTLETS AND SWITCHES BEFORE BE PROVIDED WITH USER ADJUSTABLE TIME DELAY(15 SEC. TO 20 MINUTES) FOR"SWITCH-OFF" FUNCTION
<br /> C14THEY ARE ROUGHED IN AT NO EXTRA COST,
<br /> 0 3. A SUPPORT SHALL BE PROVIDED NOT MORE THAN 3 FT. FROM ANY CHANGE IN DIRECTION. AND ADJUSTABLE SENSITIVITY.
<br /> r ADDITIONAL SUPPORTS TO THOSE SPECIFIED ABOVE SHALL BE INSTALLED WHERE REQUIRED TO SUIT JOB 10. SEPARATION OF WIRING OF DIFFERENT VOLTAGE CLASSIFICATIONS: 8. LOW VOLTAGE WIRING IS NOT REQUIRED TO BE IN CONDUIT EXCEPT IN HARDLID CEILINGS WHERE
<br /> I CONDITIONS AND TO PROVIDE A SECURE INSTALLATION. ALL HANGERS AND SUPPORTS SHALL BE THE SUCH WIRES SHALL BE RUN IN CONDUIT.
<br /> o PRODUCTS OF ONE MANUFACTURER. A. WIRING FOR DIFFERENT VOLTAGE CLASSIFICATIONS SHALL BE INSTALLED IN ENTIRELY SEPARATE
<br /> C4 RACEWAYS/CONDUITS SYSTEM AND ENCLOSURES/BOXES, 262726. WIRING DEVICES:
<br /> C-4 260533. PULL OR JUNCTION BOXES:
<br /> 1. INSTALL WHERE INDICATED, OR AS REQUIRED BY CODE, PULL BOXES AND JUNCTION BOXES OF CLASSIFICATION 1 -0 TO 30V 1. UNITS SHALL BE EQUAL TO THE DEVICES SET FORTH HEREIN, IN STANDARD COLORS (BROWN,
<br /> SUFFICIENT SIZE AND CAPACITY TO FACILITATE ALL WIRING. BOXES SHALL BE SIZED TO PROPERLY CLASSIFICATION 2 - 100 TO 250V WHITE, GREY, BEIGE OR IVORY)AS SELECTED BY THE ARCHITECT:
<br /> ACCOMMODATE ALL CONDUCTORS ENTERING SAME. CLASSIFICATION 3 -251 TO 500V A. WIRING DEVICES LEVITON# HUBBELL# P&S#
<br /> SINGLE POLE SWITCH, 15A 1201-2 HBL1201 PS15AC1
<br /> B. PARTICULAR ATTENTION SHALL BE PAID TO THE WIRING FOR DOUBLE POLE SWITCH, 15A 1202-2 HBL1202 PS15AC2
<br /> 2, BOXES SHALL BE OF THE SHAPE AND SIZE BEST SUITED FOR THE PARTICULAR APPLICATION AND THREE WAY SWITCH, 15A 1203-2 HBL1203 PS15AC3
<br /> SHALL BE SUPPORTED DIRECTLY TO STRUCTURAL MEMBERS, FRAMING OR BLOCKING BY MEANS OF 1. ROOF TOP CONVENIENCE OUTLETS FOR SERVICING ROOF TOP EQUIPMENT. DUPLEX CONV. OUTLET, 15A 5262 HBL5262 5262
<br /> SCREWS,ANCHORS, BOLTS OR EMBEDDED IN MASONRY.
<br /> DUPLEX CONV. OUTLET, 20A 5362 HBL5362 5362
<br /> o A. SWITCH AND RECEPTACLE BOX SHALL BE ONE PIECE DRAWN OR STAMPED STEEL BOXES 2. LINE VOLTAGE CONTROLS FOR ROOF TOP MVAC AND OTHER REQUIREMENTS. DUPLEX CONV. GFI OUTLET, 15A 6599 GF15 1595E
<br /> j MINIMUM SIZE SHALL BE FOUR INCHES (4")SQUARE. BOXES SHALL BE FITTED WITH FLUSH DEVICE DUPLEX CONV. GFI OUTLET, 20A 6899 GF15 2095L
<br /> N COVERS, PLASTER RINGS, OR TILE SWITCH RINGS IN MASONRY IN AREA WHERE EXPOSED WIRING IS C. DISCONNECTS SHALL NOT BE USED AS THROUGH RACEWAYS FOR WIRING NOT DIRECTLY
<br /> PERMISSIBLE, BOXES SHALL BEFITTED WITH SURFACE TYPE COVERS. SERVING THE DISCONNECTS. SERVICING OUTLETS SHALL NOT BE MOUNTED ON DISCONNECTS. 2. THE CONTROLLED OUTLET SHALL HAVE PERMANENT UNIQUE MARKING PROVIDED BY THE
<br /> CL
<br /> MANUFACTURER OF THE RECEPTACLE.
<br /> 4) B. LIGHTING OUTLETS SHALL BE FOUR INCHES (4")OCTAGON, MINIMUM. 260551. INSTALLATION OF RACEWAYS AND FITTINGS
<br /> 3. THE MOUNTING HEIGHTS OF LIGHT SWITCHES, RECEPTACLES AND CONTROLS SHALL BE MAXIMUM
<br /> WMB PROJECT:
<br /> � C. FLOOR BOXES: SHALL BE SINGLE SERVICE OR MULTI-SERVICE AS NOTED ON PLANS. BOXES 1. CONCEAL RACEWAYS WITHIN CEILINGS, WALLS,AND FLOORS EXCEPT WHERE EXPOSED 48"MEASURED TO THE TOP OF BOXES OR MINIMUM 16"TO THE BOTTOM OF BOXES. SEE"LEGEND" FOR
<br /> E SHALL BE FULLY ADJUSTABLE BEFORE AND AFTER CONCRETE POUR. BOXES SHALL BE FURNISHED RACEWAYS ARE SPECIFICALLY PERMITTED. ACTUAL MOUNTING HEIGHTS OF DEVICES.VERIFY HEIGHT WITH ARCHITECT WHERE AN ACTUAL MOUNTING 20-03�
<br /> WITH ALL REQUIRED ACCESSORIES FOR A COMPLETE AND WORKING INSTALLATION, INCLUDING DEVICE HEIGHT IS NOT CALLED OUT ON PLANS.
<br /> MOUNTING BRACKETS, BOTH POWE=R AND COMMUNICATIONS,TRIM RING/COVERPLATE OR FLOOR PORT 2. WHERE CONDUIT IS ALLOWED TO BE EXPOSED, INSTALL THE CONDUIT PARALLEL WITH OR AT
<br /> oACTIVATION KIT. PROVIDE POWER DEVICES AND TERMINATIONS. SINGLE SERVICE BOX SMALL BE RIGHT ANGLES TO STRUCTURAL_MEMBERS, WALLS,AND LINES OF THE BUILDING. 4. SINGLE RECEPTACLE SERVED BY INDIVIDUAL 20A BRANCH CIRCUIT DEDICATED TO THE OUTLET
<br /> HUBBELL, NON-METALLIC, CONCRETE FLOOR BOX TYPE PFB1 WITH FLUSH BRASS ROUND COVERPLATE SHALL BE 20A RATED PER CEC 210.21(13)(1).ALL OTHERS SHALL BE 15A RATED.
<br /> AS HUBBELL#S3925, FLANGE AS HUBBELL#53082 AND DUPLEX 120V, 15A OUTLET. MULTI-SERVICE 1 INSTALL WHERE INDICATED, OR AS REQUIRED BY CODE, PULLBOXES AND JUNCTION BOXES OF
<br /> FLOOR BOXES SHALL BE AS HUBBELL SYSTEM ONE AS FOLLOWS: SUFFICIENT SIZE TO FACILITATE WIRING. BOXES SHALL BE SIZED TO PROPERLY ACCOMMODATE ALL 5. ALL 15A AND 20A, 120V OUTLETS IN KITCHEN SHALL BE GFCI PER CEC 210.8(B)(2). LOCATE SUCH
<br /> a CONDUCTORS ENTERING SAME. OUTLETS SO THAT THEY ARE ACCESSIBLE AFTER APPLIANCES THAT ARE PLUGGED INTO THE OUTLETS ARE
<br /> N a} ON-GRADE-CASTIRON#S1CF6 IN PLACE. �O■
<br /> o b) UPPER CONCRETE FLOORS-STEEL#S1 SFB 4. DO NOT INSTALL CONDUIT OR TUBING WHICH HAS BEEN CRUSHED OR DEFORMED.
<br /> DROP E SSIpH
<br /> N c) AV BOX-#S1IC 1 AV
<br /> #S 5. RUN CONDUCTORS OF SAME CIRCUIT IN SAME CONDUIT. RUN CONDUCTORS OF DIFFERENT C ALL RECEPTACLES INSTALLED OUTDOORS SHALL BE WEATHERPROOF AND HAVE GROUND FAULT 4512 Feather River Cr#F.Stockton.CA 95219 4� R� c• s
<br /> d) NON-METALLIC 1 #S1 PFB PROVIDE COVERPLATE AND FLANGE, FINISH PER ARCHITECT. PROVIDE CIRCUIT INTERRUPTER PROTECTION. 2p9-478-8270 I www.hcs-eng.com ���\G,�,P
<br /> MINIMUM (1) DUPLEX OUTLET AND A4-PORT MULTISERVICE COMMUNICATIONS FRAMES. VERIFY EXACT VOLTAGE SYSTEMS IN SEPARATE CONDUITS. y Z
<br /> REQUIREMENT WITH OWNER PRIOR TO PROCUREMENT ACS 7. 120V, 15A AND 20A RECEPTACLES ARE NOW SUBJECT TO CALIFORNIA ENERGY CODE, SECTION No. El 4.303
<br /> 130.5(4).ALL SUCH OUTLETS SHALL BE CONSIDERED AS UNCONTROLLED EXCEPT THOSE WHICH ARE EngineeringH Richard G Srn)th,PE richard@hcs-eng.com xp, 6-30-21
<br /> path://john/1714
<br /> ❑Bhupendra Patel.PE bhupendraofts-e 50 years �Efizabcth Aguilar elizabeth@hcseng.c
<br /> PARAGRAPH BELOW.
<br /> SPECIFICALLY CALLED OUT ON THE PLANS AS CONTROLLED. SEE"CONTROLLED 120V RECEPTACLES" 9T<FC TR1
<br /> o�
<br /> PROJECT is 2020.232 8/1112020 7:00:47 AM Copyright WMI3,Inc.
<br />
|