INSTALL_2021 - Laserfiche WebLink

Home Browse Search

VEEDER ROOT CARBON CANISTER VAPOR POLISHER COMPLIANCE AND INSTALLATION NOTES THESE NOTES ARE APPLICABLE TO NEW AND RETROFIT INSTALLATIONS LOCATION OF VAPOR PROCESSING EQUIPMENT CA FIRE CODE: CFC 2010 §2206.7.9.2.2 LOCATION EQUIPMENT VAPOR -PROCESSING EQUIPMENT SHALL BE LOCATED AT OR ABOVE GRADE. SOURCES OF IGNITION SHALL BE LOCATED NOT LESS THAN 50 FEET (15240MM) FROM FUEL -TRANSFER AREAS AND NOT LESS THAN 18 INCHES (457.2MM) ABOVE TANK FILL OPENINGS AND TOPS OF DISPENSER ISLANDS. VAPOR -PROCESSING UNITS SHALL BE LOCATED NOT LESS THAN 10 FEET (3048MM) FROM THE NEAREST BUILDING OR PROPERTY LINE OF A PROPERTY WHICH CAN BE BUILT UPON. EXCEPTION: WHERE THE REQUIRED DISTANCES TO BUILDINGS, PROPERTY LINES OR FUEL -TRANSFER AREAS CANNOT BE OBTAINED, MEANS SHALL BE PROVIDED TO PROTECT EQUIPMENT AGAINST FIRE EXPOSURE. ACCEPTABLE MEANS INCLUDE: 1. APPROVED PROTECTIVE ENCLOSURES, WHICH EXTEND AT LEASE 18 INCHES (457.2MM) ABOVE THE EQUIPMENT, CONSTRUCTED OF FIRE-RESISTANT OR NON-COMBUSTIBLE MATERIALS OR 2. FIRE PROTECTION USING AN APPROVED WATER -SPRAY SYSTEM. VAPOR -PROCESSING EQUIPMENT SHALL BE LOCATED A MINIMUM OF 20 FEET (6096MM) FROM DISPENSING DEVICES. PROCESSING EQUIPMENT SHALL BE PROTECTED AGAINST PHYSICAL DAMAGE BY GUARDRAILS, CURBS, PROTECTIVE ENCLOSURES OR FENCING. WHEN APPROVED PROTECTIVE ENCLOSURES ARE USED, APPROVED MEANS SHALL BE PROVIDED TO VENTILATE THE VOLUME WITHIN THE ENCLOSURE TO PREVENT POCKETING OF FLAMMABLE VAPORS. ADDITIONAL INSTALLATION NOTES: 1. ALL INSTALLATIONS OF VEEDER ROOT CARBON CANISTER VAPOR POLISHER INSTALLATIONS SHALL BE REVIEWED BY BP LOGISTICS FOR APPROVAL PRIOR TO SUBMITTALS TO AUTHORITIES HAVING JURISDICTION AND RE -REVIEWED BY BP LOGISTICS AFTER PERMIT APPROVALS ARE OBTAINED. ADDITIONALLY INDIVIDUAL SITE PLANS NEED TO BE REVIEWED BY THE ECS TO MAKE SURE THERE ARE NO SENSITIVE RECEPTORS WITHIN 1000 FEET OF THE EQUIPMENT LOCATION. 2. ON EXISTING FACILITIES CONTRACTOR TO PERFORM LIQUID AND VAPOR TIGHTNESS TEST ON VENT LINES PRIOR TO PROCEEDING WITH INSTALLATION OF THE VEEDER ROOT SYSTEM, REPORT TO BP PRODUCT MANAGER WITH RESULTS. 3. THE VENT DISCHARGE SHALL BE LOCATED AND DIRECTED SO THAT VAPORS WILL DISPERSE. VAPORS SHALL BE DIRECTED UPWARD AND HORIZONTALLY AWAY FROM ADJACENT WALLS. VENT OUTLETS SHALL BE LOCATED SO AS NOT TO BE TRAPPED BY EAVES OR OTHER OBSTRUCTIONS AND SHALL BE AT LEAST 5 FEET FROM BUILDING OPENINGS. DISCHARGE SHALL NOT BE LESS THAN 12' FROM FINISH GRADE. VENTS SHALL BE INSTALLED IN ACCORDANCE WITH NEPA 30 (2012). 4. VENT RISERS SHOULD STAND NO LESS THAN 3' FROM THE OUTSIDE OF CURB. 5. THE CONTRACTOR IS RESPONSIBLE FOR SHORING AND THE PROTECTION IN PLACE OF EXISTING FACILITIES. IF A DOWNSLOPE EXISTS TOWARD THE LOCATION OF THE VAPOR -PROCESSING 6. MAINTAIN 5 FEET CLEAR AROUND CARBON CANISTER VAPOR POLISHER UNIT FROM A FUEL -TRANSFER AREA, THE CHIEF IS AUTHORIZED TO REQUIRE FOOTPRINT TO GRADE. ADDITIONAL SEPARATION BY DISTANCE AND HEIGHT. CFC 2010 §2206.7.9.2.3 INSTALLATION VAPOR -PROCESSING UNITS SHALL BE SECURELY MOUNTED ON CONCRETE, MASONRY OR STRUCTURAL STEEL SUPPORTS ON CONCRETE OR OTHER NON-COMBUSTIBLE FOUNDATIONS. NOTE: BP DOES NOT PERMIT THE VAPOR -PROCESSING EQUIPMENT TO BE INSTALLED ON ROOFS OF BUILDINGS OR CANOPY STRUCTURES. SEE ALTERNATE MOUNTING DETAILS FOR EXISTING SITES WHERE VENT RISERS AR MOUNTED AT ROOFS. EXISTING CONDITIONS: THE CONTRACTOR SHALL BE RESPONSIBLE FOR DETERMINING THE EXISTING CONTROLLING SITE CONDITIONS AND FOR COMPLIANCE WITH LOCAL ORDINANCES AND CURRENT CALIFORNIA BUILDING CODES. APPLICABLE CODES: ALL WORK SHALL BE IN STRICT ACCORDANCE WITH THE LATEST EDITION OF THE CALIFORNIA BUILDING CODE AND REFERENCED STANDARDS. PLANS AND PERMITS: THE CONTRACTOR SHALL OBTAIN ALL NECESSARY ENCROACHMENT PERMITS AND SHALL POSSESS APPROVED PLANS PRIOR TO BEGINNING OF CONSTRUCTION. UTILITY LOCATIONS: THE CONTRACTOR WILL BE REQUIRED TO NOTIFY MEMBERS OF UNDERGROUND SERVICE ALTER (U.S.A.) 48 HOURS IN ADVANCE OF PERFORMING EXCAVATION WORK BY CALLING THE TOLL-FREE NUMBER (800)-227-2600. EXCAVATION FOR THE PURPOSE OF THIS REQUIREMENT, IS DEFINED AS BEING 18" OR MORE IN DEPTH BELOW THE EXISTING SURFACE. 7. BALL FLOAT VALVES ARE CURRENTLY INSTALLED AS BP STANDARD PRACTICE FOR PROTECTION OF WETTING OF THE VENT AND STAGE II VAPOR PIPING. CONTRACTOR TO CONFIRM THE EXISTING INSTALLATION AND REPLACE ALL BALL FLOAT VALVES AT EXISTING FACILITIES. 8. CONTRACTOR SHALL CONFIRM AND LABEL ALL VENT STACKS WITH CORRECT PRODUCT VENT TIE IN TO AVOID PRODUCT CONTAMINATION AND IMPROPER PROCESSOR TIE-IN. PROVIDE CONFIRMATION ON PIPE AND TANK CHECKLIST (LABEL MAKER OK). "DO NO INSTALL ON DIESEL" 9. THERE SHALL BE NO POCKETS OR LIQUID TRAPS IN ANY OF THE CONNECTED PIPING FROM THE VEEDER ROOT CARBON CANISTER VAPOR POLISHER TO THE VENT STACK TIE-IN POINT. 10. THE VENT STACK RACK AND RISERS SHALL BE GROUNDED. TIE THE GROUND WIRE FROM THE VENT STACKS TO THE UST SYSTEM GROUND. 11. PRIOR TO PERFORMING MAINTENANCE, TEST PORT VALVE MUST BE VENTED TO ATMOSPHERE. 12. VEEDER ROOT SYSTEM TO BE LEAK -TESTED PRIOR TO START-UP TO AVOID LEAKAGE TO ATMOSPHERE. 13. ANY SPENT CARBON FROM CANISTER SHALL BE TREATED AS HAZARDOUS WASTE AND DISPOSED OF PROPERLY 14. INSPECT FOR VEEDER ROOT CARBON CANISTER VAPOR POLISHER FOR DAMAGE PRIOR TO START UP OR RE-COMMISIONING AFTER SERVICE. ELECTRICAL INSTALLATION NOTES: 1. ALL ELECTRICAL INSTALLATIONS ARE TO BE PER NEC/CEC CODE FOR THE AREA INSTALLED. INSTALLATION IN A CLASSIFIED AREA IS AN EXCEPTION TO THE NORMAL SITING AND SHALL REQUIRE FURTHER REVIEW OF BP PROJECT MANAGER. 2. ENSURE THE VEEDER ROOT CARBON CANISTER VAPOR POLISHER IS BONDED AND GROUNDED TO THE SITE SYSTEM AND TO THE SITE TANK GROUNDING SYSTEM TO ELIMINATE THE POSSIBILITY OF ELECTRICAL DISCHARGE AS AN IGNITION SOURCE. 3. BONDING AND GROUNDING: BONDING AND GROUNDING GUIDELINES FOR CONSTRUCTION REGARDING DISPENSING EQUIPMENT ARE TO BE IN PLACE AND IN ACCORDANCE WITH PETROLEUM EQUIPMENT INSTITUTE (PEI). ADDITIONAL INSTALLATION NOTES AT DISPENSERS: 1. SOME DISPENSER NOZZLES HOLSTERS ARE NOT COMPATIBLE WITH THE CURRENT VST DESIGN. CONSULT WITH BP PROJECT MANAGER FOR A LIST OF DISPENSERS THAT ARE NOT COMPATIBLE WITH THE DESIGN AND DO NOT INSTALL VST AT LOCATIONS WHERE THESE DISPENSERS EXIST. 2. THE PRESSURE SENSOR LOCATED IN THE DISPENSER SUMP CLOSEST TO THE TANK FARM SHALL BE PREFERABLY MOUNTED OUTSIDE THE DISPENSER CONTAINMENT SUMP OR ABOVE THE HIGHEST PENETRATION FITTING. DURING CONTAINMENT SUMP CERTIFICATION TESTING CONTRACTOR TO REMOVE THE PRESSURE SWITCH TO AVOID POSSIBLE WATER DAMAGE. 3. THE PRESSURE SENSOR MUST BE INSTALLED IN THE VERTICAL POSITION, SENSING PORT POINTING DOWN, AND WHEN REQUIRED BY AUTHORITY HAVING JURISDICTION, THE CONNECTION TO THE VAPOR LINE MUST BE BELOW THE SHEAR VALVE 4. THE 3 -WAY VALVE TEST PORT ON THE PRESSURE SENSOR IN THE DISPENSER CLOSEST TO THE TANK FARM SHALL BE "CAR SEALED" WITH LABELS INDICATING CORRECT OPERATING POSITION. VALVE TO REMAIN CLOSED FOR NORMAL OPERATION TO AVOID FALSE PRESSURE READING BY THE ISD SOFTWARE. 5. THE DISPENSERS MUST BE A BALANCE TYPE DISPENSER. 6. THE DISPENSERS MUST BE CARB APPROVED UNIHOSE TYPES UNLESS PERMITTED BY AUTHORITY HAVING JURISDICTION. 7. THERE SHALL BE NO FLOW LIMITERS ALLOWED FOR THE VST SYSTEM. 8. FOLLOW PEI RP -400 FOR ELECTRICAL CONTINUITY OF HANGING HARDWARE 9. THE VST HANGING HARDWARE IS CAPABLE OF LONGER HOSE LENGTHS. MAXIMUM HOSE LENGTH WHEN CONNECTED IS LIMITED TO 15'-0" CONSULT WITH DISPENSER MANUFACTURER FOR EXTENDED HOSE REACH DESIGN ALTERNATIVE. TESTING NOTES: PER CARB E.O. VR -204 ALL EXISTING SINGLE WALL VENT AND VAPOR PIPING INSTALLATIONS AND NEW DOUBLE WALL VENT AND VAPOR INSTALLATIONS SHALL HAVE THE FOLLOWING TESTS TO BE COMPLETED WITHIN 60 DAYS AFTER START-UP AND AT LEAST ONCE IN EACH 12 MONTH PERIOD USING THE FOLLOWING TEST PROCEDURES. TP -201.3 DETERMINATION OF 2 -INCH WC STATIC PRESSURE PERFORMANCE OF VAPOR RECOVERY SYSTEMS OF DISPENSING FACILITIES (March 17, 1999); TP -201.4 DYNAMIC BACK PRESSURE (July 3, 2002) IN ACCORDANCE WITH THE CONDITION LISTED IN ITEM 1 OF THE VAPOR COLLECTION SECTION OF EXHIBIT 2 OF THE VR -204 EXECUTIVE ORDER; IN ADDITION BP PROCEDURES REQUIRE THE EXECUTION OF METHODOLOGY 6 EXHIBIT 4 OF THE VR -204 EXECUTIVE ORDER, REQUIRED ITEMS IN CONDUCTING TP -201.3; ARCO BP WEST COAST PRODUCTS, LLC EXHIBIT 5 OF THE VR -204 EXECUTIVE ORDER, LIQUID REMOVAL TEST PROCEDURE; 01/18/2021 BID PACKAGE EXHIBIT 6 OF THE VR -204 EXECUTIVE ORDER, HYDROCARBON SENSOR VERIFICATION TEST; EXHIBIT 8 OF THE VR -204 EXECUTIVE ORDER, VAPOR PRESSURE SENSOR VERIFICATION TEST; EXHIBIT 9 OF THE VR -204 EXECUTIVE ORDER, DETERMINATION OF VST PROCESSOR ACTIVATION PRESSURE; AND EXHIBIT 11 OF THE VR -204 EXECUTIVE ORDER, OPERABILITY TEST PROCEDURE FOR THE VEEDER-ROOT ISD FLOW METER. SHORTER TIME PERIODS MAY BE SPECIFIED IN ACCORDANCE WITH LOCAL DISTRICT REQUIREMENTS. NOTIFICATION OF TESTING, AND SUBMITTAL OF TEST RESULTS, SHALL BE DONE IN ACCORDANCE WITH LOCAL DISTRICT REQUIREMENTS AND PURSUANT TO POLICIES ESTABLISHED BY THAT DISTRICT. ALTERNATIVE TEST PROCEDURES, INCLUDING MOST RECENT VERSIONS OF THE TEST PROCEDURES LISTED ABOVE, MAY BE USED IF DETERMINED BY THE ARB EXECUTIVE OFFICER OR EXECUTIVE OFFICER DELEGATE, IN WRITING, TO YIELD EQUIVALENT RESULTS. IT IS FURTHER ORDERED THAT THE FOLLOWING REQUIREMENTS ARE MADE A CONDITION OF CERTIFICATION. THE OWNER OR OPERATOR OF THE VST PHASE II EVR SYSTEM INCLUDING VEEDER-ROOT ISD SHALL CONDUCT, AND PASS, THE FOLLOWING TESTS NO LATER THAN 60 DAYS AFTER STARTUP USING THE FOLLOWING TEST PROCEDURE: EXHIBIT 10, NOZZLE BAG TEST PROCEDURE. NOTIFICATION OF TESTING, AND SUBMITTAL OF TEST RESULTS, SHALL BE DONE IN ACCORDANCE WITH LOCAL DISTRICT REQUIREMENTS AND PURSUANT TO THE POLICIES ESTABLISHED BY THAT DISTRICT. ALTERNATIVE TEST PROCEDURES, INCLUDING MOST RECENT VERSIONS OF THE TEST PROCEDURES LISTED ABOVE, MAY BE USED IF DETERMINED BY THE ARB EXECUTIVE OFFICER OR EXECUTIVE OFFICER DELEGATE, IN WRITING, TO YIELD EQUIVALENT RESULTS. CLIENT: 4: bp 'Ad & 11F ARCO BP WEST COAST PRODUCTS, LLC NO. DATE DESCRIPTION 0 01/18/2021 BID PACKAGE 0 0 0 0 0 0 0 io SEAL: FESS /0 Cf-�gp�l NO. 36475 * XP. 6-30-22 ATF � CAUF�� z LU w •Q Co U zoo 0 Z z~�- 0v7rn� mZ UOQ �QU LU Cr QLLI I I w w �Z}LL 0 O z o �Z UzOrn (I II zUUo zz Q p Z N wz0-- �w LLJ< z Lo Q -- 06 z . t Z � Q Lu 00 w z (D z 0 2 0- z g oL DEVELOPMENT INFORMATION: SITE ADDRESS: ADDRESS 2510 S. STATE HWY 99 W. FRONTAGE ROAD SAN JOAQUIN COUNTY, CA 95205 DESIGNED BY: CHECKED BY: DRAWN BY: DATE: PROJECT NO: DRAWING TITLE: DESIGN INTENT: VEEDER-ROOT CARBON CANISTER VAPOR POLISHER COMPLIANCE AND INSTALLATION NOTES (CALIFORNIA ONLY) SHEET NO: